最新ABB robotstudio使用详细步骤资料.docx
《最新ABB robotstudio使用详细步骤资料.docx》由会员分享,可在线阅读,更多相关《最新ABB robotstudio使用详细步骤资料.docx(27页珍藏版)》请在冰豆网上搜索。
![最新ABB robotstudio使用详细步骤资料.docx](https://file1.bdocx.com/fileroot1/2023-2/26/dae01e15-43da-4986-8751-d561bbb03a2f/dae01e15-43da-4986-8751-d561bbb03a2f1.gif)
最新ABBrobotstudio使用详细步骤资料
搬运码垛工作站建模
1、创建机器人系统
2、创建动态输送链
3、创建动态夹具
4、工作站逻辑连接
5、添加IO(设置好需重启)
6、示教目标点(同步到RAPID)
7、RAPID编程
一、创建机器人系统
1、创建空工作站
2、导入IRB260机器人模型
3、从布局创建机器人系统,勾选Chinese和709-1网络
二、创建动态输送链
1、添加输送链并修改位置
2、创建600*400*200的物料并修改位置
3、添加一个smart组件
4、添加source组件
5、设置物料本地原点
6、添加LINEMOVER和QUEUE组件
7设置LINEMOVER属性
8、添加面传感器组件
9、设置输送链不能被传感器检测
10、设置SC_输送链的属性连接
11、设置信号连接
12、添加信号处理组件,用于检测传感器下降沿
13、传感器下降沿触发source进行copy
14、传感器与SC输送链的输出联系
15、添加仿真开始结束组件,用于激活传感器
16、添加置位复位组件,对仿真开始结束信号进行保持
17、
18、进行仿真设定选择SC——输送链进行验证
三、创建动态夹具
1、先制作一个吸盘模型,然后设置成工具,并安装到机器人法拉盘
2、添加SMART组件
3、添加ATTACHER和DETACHER组件
4、设置属性
5、添加一个线传感器组件
6、线传感器设置属性
7、设置吸盘工具不能被传感器检测
8、把线传感器安装到吸盘(不更新位置,保持当前位置)
9、设置属性连接
10、添加信号及连接
11、添加信号处理取非和锁定组件
12、继续信号连接
13、添加一个示教物料
14、应用手动线性验证SC_工具
四、工作站逻辑连接
五、参考代码
MODULEMainMoudle
PERStooldatatGrip:
=[TRUE,[[0,0,200],[1,0,0,0]],[25,[0,0.00109327,116.889],[1,0,0,0],0,0,0]];
!
吸盘工具数据
PERSloaddataLoadEmpty:
=[0.01,[0,0,1],[1,0,0,0],0,0,0];
PERSloaddataLoadFull:
=[40,[0,0,50],[1,0,0,0],0,0,0];
!
有效载荷数据
PERSrobtargetpHome:
=[[1620.00,-0.00,1331.59],[1.27986E-06,-0.707107,-0.707107,1.27986E-06],[0,0,1,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];
!
基准点
PERSrobtargetpActualPos:
=[[1620,-1.87531E-14,1331.59],[1.27986E-06,-0.707107,-0.707107,1.27986E-06],[0,0,1,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];
!
实际点
PERSrobtargetpPick1:
=[[1488.007792464,376.826660408,476.964684195],[0,0.707106307,0.707107256,0],[0,0,1,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
!
1路拾取目标点
PERSrobtargetpPlace1:
=[[-292.446,1263.27,55.4492],[0,0.707107,0.707106,0],[1,0,2,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];
!
1路放置基准点
PERSrobtargetpBase1_0:
=[[-292.446294945,1263.272085268,55.449220723],[0,0.707107387,0.707106176,0],[1,0,2,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
!
1路放置0度姿态
PERSrobtargetpBase1_90:
=[[-391.976797324,1362.469634994,55.449159414],[0,1,-0.000030621,0],[1,0,3,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
!
1路放置90度姿态
PERSrobtargetpPick2:
=[[1488.013130905,-358.406014736,476.965039287],[0,0.707106307,0.707107256,0],[-1,0,0,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
PERSrobtargetpPlace2:
=[[-317.378,-1857.99,55.449],[0,0.707108,0.707106,0],[-2,0,-1,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];
PERSrobtargetpBase2_0:
=[[-317.378137718,-1857.993871961,55.448967354],[0,0.707107745,0.707105817,0],[-2,0,-1,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
PERSrobtargetpBase2_90:
=[[-407.525988074,-1755.902485322,55.449282402],[0,1,-0.000031217,0],[-2,0,0,0],[9E9,9E9,9E9,9E9,9E9,9E9]];
PERSspeeddataMinSpeed:
=[1000,300,5000,1000];
PERSspeeddataMidSpeed:
=[2500,400,5000,1000];
PERSspeeddataMaxSpeed:
=[4000,500,5000,1000];
!
搬运速度定义
PERSboolbPalletFull1:
=FALSE;
PERSboolbPalletFull2:
=FALSE;
!
逻辑布尔量,拾取后为UE,放置后为FALSE
PERSnumnCount1:
=1;
PERSnumnCount2:
=1;
!
输送链计数
PROCMain()
rInitAll;
WHILETRUEDO
IFdiBoxInPos1=1ANDdiPalletInPos1=1ANDbPalletFull1=FALSETHEN
rPick1;
rPlace1;
ENDIF
IFdiBoxInPos2=1ANDdiPalletInPos2=1ANDbPalletFull2=FALSETHEN
rPick2;
rPlace2;
ENDIF
WaitTime0.1;
ENDWHILE
ENDPROC
PROCrInitAll()
ResetdoGrip;
pActualPos:
=CRobT(\tool:
=tGrip);
pActualPos.trans.z:
=pHome.trans.z;
MoveLpActualPos,MinSpeed,fine,tGrip\WObj:
=wobj0;
MoveJpHome,MidSpeed,fine,tGrip\WObj:
=wobj0;
bPalletFull1:
=FALSE;
nCount1:
=1;
bPalletFull2:
=FALSE;
nCount2:
=1;
ENDPROC
PROCrPick1()
MoveJOffs(pPick1,0,0,400),MaxSpeed,z50,tGrip\WObj:
=wobj0;
MoveLpPick1,MinSpeed,fine,tGrip\WObj:
=wobj0;
SetdoGrip;
WaitTime0.3;
GripLoadLoadFull;
MoveLOffs(pPick1,0,0,400),MinSpeed,z50,tGrip\WObj:
=wobj0;
ENDPROC
PROCrPick2()
MoveJOffs(pPick2,0,0,400),MaxSpeed,z50,tGrip\WObj:
=wobj0;
MoveLpPick2,MinSpeed,fine,tGrip\WObj:
=wobj0;
SetdoGrip;
WaitTime0.3;
GripLoadLoadFull;
MoveLOffs(pPick2,0,0,400),MinSpeed,z50,tGrip\WObj:
=wobj0;
ENDPROC
PROCrPlace1()
rPosition1;
MoveJOffs(pPlace1,0,0,400),MidSpeed,z50,tGrip\WObj:
=wobj0;
MoveLpPlace1,MinSpeed,fine,tGrip\WObj:
=wobj0;
ResetdoGrip;
WaitTime0.3;
GripLoadLoadEmpty;
MoveLOffs(pPlace1,0,0,400),MidSpeed,z50,tGrip\WObj:
=wobj0;
MoveJOffs(pPick1,0,0,400),MaxSpeed,z50,tGrip\WObj:
=wobj0;
nCount1:
=nCount1+1;
IFnCount1>20THEN
bPalletFull1:
=TRUE;
ENDIF
ENDPROC
PROCrPlace2()
rPosition2;
MoveJOffs(pPlace2,0,0,400),MaxSpeed,z50,tGrip\WObj:
=wobj0;
MoveLpPlace2,MinSpeed,fine,tGrip\WObj:
=wobj0;
ResetdoGrip;
WaitTime0.3;
GripLoadLoadEmpty;
MoveLOffs(pPlace2,0,0,400),MidSpeed,z50,tGrip\WObj:
=wobj0;
MoveJOffs(pPick2,0,0,400),MaxSpeed,z50,tGrip\WObj:
=wobj0;
nCount2:
=nCount2+1;
IFnCount2>20THEN
bPalletFull2:
=TRUE;
ENDIF
ENDPROC
PROCrPosition1()
TESTnCount1
CASE1:
pPlace1:
=Offs(pBase1_0,0,0,0);
CASE2:
pPlace1:
=Offs(pBase1_0,600+10,0,0);
CASE3:
pPlace1:
=Offs(pBase1_90,0,400+10,0);
CASE4:
pPlace1:
=Offs(pBase1_90,400+10,400+10,0);
CASE5:
pPlace1:
=Offs(pBase1_90,800+20,400+10,0);
CASE6:
pPlace1:
=Offs(pBase1_0,0,600+10,200);
CASE7:
pPlace1:
=Offs(pBase1_0,600+10,600+10,200);
CASE8:
pPlace1:
=Offs(pBase1_90,0,0,200);
CASE9:
pPlace1:
=Offs(pBase1_90,400+10,0,200);
CASE10:
pPlace1:
=Offs(pBase1_90,800+20,0,200);
CASE11:
pPlace1:
=Offs(pBase1_0,0,0,400);
CASE12:
pPlace1:
=Offs(pBase1_0,600+10,0,400);
CASE13:
pPlace1:
=Offs(pBase1_90,0,400+10,400);
CASE14:
pPlace1:
=Offs(pBase1_90,400+10,400+10,400);
CASE15:
pPlace1:
=Offs(pBase1_90,800+20,400+10,400);
CASE16:
pPlace1:
=Offs(pBase1_0,0,600+10,600);
CASE17:
pPlace1:
=Offs(pBase1_0,600+10,600+10,600);
CASE18:
pPlace1:
=Offs(pBase1_90,0,0,600);
CASE19:
pPlace1:
=Offs(pBase1_90,400+10,0,600);
CASE20:
pPlace1:
=Offs(pBase1_90,800+20,0,600);
DEFAULT:
TPErase;
TPWrite"theCounterofline1iserror,pleasecheckit!
";
Stop;
ENDTEST
ENDPROC
PROCrPosition2()
TESTnCount2
CASE1:
pPlace2:
=Offs(pBase2_0,0,0,0);
CASE2:
pPlace2:
=Offs(pBase2_0,600+10,0,0);
CASE3:
pPlace2:
=Offs(pBase2_90,0,400+10,0);
CASE4:
pPlace2:
=Offs(pBase2_90,400+10,400+10,0);
CASE5:
pPlace2:
=Offs(pBase2_90,800+20,400+10,0);
CASE6:
pPlace2:
=Offs(pBase2_0,0,600+10,200);
CASE7:
pPlace2:
=Offs(pBase2_0,600+10,600+10,200);
CASE8:
pPlace2:
=Offs(pBase2_90,0,0,200);
CASE9:
pPlace2:
=Offs(pBase2_90,400+10,0,200);
CASE10:
pPlace2:
=Offs(pBase2_90,800+20,0,200);
CASE11:
pPlace2:
=Offs(pBase2_0,0,0,400);
CASE12:
pPlace2:
=Offs(pBase2_0,600+10,0,400);
CASE13:
pPlace2:
=Offs(pBase2_90,0,400+10,400);
CASE14:
pPlace2:
=Offs(pBase2_90,400+10,400+10,400);
CASE15:
pPlace2:
=Offs(pBase2_90,800+20,400+10,400);
CASE16:
pPlace2:
=Offs(pBase2_0,0,600+10,600);
The鍏畾Ma愪wreathChen?
CASE17:
The鎴愭湰鎺у埗pPlace2:
=Offs(pBase2_0,600+10,600+10,600);
CASE18:
pPlace2:
=Offs(pBase2_90,0,0,600);
CASE19:
pPlace2:
=Offs(pBase2_90,400+10,0,600);
CASE20:
pPlace2:
=Offs(pBase2_90,800+20,0,600);
TheChenヤ綅鍣ㄥ叿DEFAULT:
TPErase;
TPWrite"theCounterofline1iserror,pleasecheckit!
";
Stop;
ENDTEST
ENDPROC
The鍖coaxs垎totieupу埆PROCrModify()
TheQi濊瘉鏃ユ湡閫佸埌MoveJpHome,MinSpeed,fine,tGrip\WObj:
=wobj0;
The鏈€?
珮Chui濇姷鎶and?
MoveJpPick1,MinSpeed,fine,tGrip\WObj:
=wobj0;
MoveJpBase1_0,MinSpeed,fine,tGrip\WObj:
=wobj0;
MoveJpBase1_90,MinSpeed,fine,tGrip\WObj:
=wobj0;
TheXuanHao綅鏍draftMoveJpPick2,MinSpeed,fine,tGrip\WObj:
=wobj0;
MoveJpBase2_0,MinSpeed,fine,tGrip\WObj:
=wobj0;
MoveJpBase2_90,MinSpeed,fine,tGrip\WObj:
=wobj0;
ENDPROC
The鎻愯Chuai鏂Gui紡
TheYue氬埗鐗╂祦ENDMODULE
TheCong㈠崟鍒嫞Lu?