螺柱焊现场故障代码及报警.docx
《螺柱焊现场故障代码及报警.docx》由会员分享,可在线阅读,更多相关《螺柱焊现场故障代码及报警.docx(15页珍藏版)》请在冰豆网上搜索。
螺柱焊现场故障代码及报警
螺柱焊报警分析
故障分类:
螺柱焊故障,根据报警信息可以分为以下几大类。
1.焊头故障
2.送料器故障
3.功率单元故障
4.控制器故障
5.通讯故障
出现故障的局部会在报警信息中出现。
在编程器的故障查询中会显示。
常见故障报警:
Fault1:
“WeldheadremainsinR-position“
故障1:
焊枪不在起始位置
E*planation:
Afterasuccessfulweldstarttheweldheadsliderailremainsinbackposition(internalsliderailcontrol).
解释:
启动焊接信号后焊枪仍然停留在滑板起始位置〔控制内部滑轨〕
Cause:
•pressed-airsupplyinterrupted.
原因:
压缩空气供给中断
•Feederfault(i.e.defectivemagneticsolenoidvalve).
送料器故障〔例如:
电磁阀损坏了〕
•Weldheadfault(i.e.weldheadgotjammed).
焊头故障〔例如:
焊头被卡住了〕
Remedy:
•ResetFault.
措施:
故障复位
•Checkpressedairsupply.
检查压缩空气供给
•CheckfuseintheFeeder.
检查送料器保险丝
•Replacefeederorweldhead.
更换送料器或焊头
•Notifyserviceengineer!
专业人员处理
Fault2:
“NoSOW“
故障2:
无接触信号
E*planation:
AfterasuccessfulweldstartSOWwasnotdetected.Thereforeweldingisnotpermitted.
解释:
启动焊接信号后无接触信号,导致无法焊接
Cause:
•Nostudincollet.
原因:
夹套里没有焊钉
•Feederwithoutweldstuds.
送料器里没有焊钉
•Stabilizerincorrectlysetorcontaminated.
支撑脚或喷嘴调整不当或太脏
•Weldcircuitinterrupted.
焊接回路中断
•Weldheadfault(i.e.weldheadgotjammed).
焊头故障〔例如:
焊头被卡住了〕
•Colletdefective.
夹持器损坏了
Remedy:
•Removeloadingfault.
措施:
排除送钉故障
•Checkadjustingofstabilizer.
检查支撑脚或喷嘴的调整状态
•Checkweldingcircuit.
检查焊接回路
•Studfeeding.
送一次钉
•Repeatweldcycle.
重复一次焊接
•Replacecollet.
更换夹持器
•Notifyserviceengineer!
专业人员处理
Fault3:
“Weldtoolnotinbackposition“
故障3:
焊头没有在焊接位置
E*planation:
Pro*imityswitchforbackpositionnotconfigured,defectiveorpowersupplymissing.
解释:
焊接位置的接近开关没有被盖住或接近开关被损坏或者没有电压
Cause:
•Dropinpressed-airsupply.
原因:
压缩空气供给气压缺乏
•Cablepackagedefective.
管线总成损坏
•Monitoringtimeafterweldingwase*ceeded.
焊接之后的检测时间超差
•Weldheaddefective.
焊头损坏
•Feederdefective.
送料器损坏
•Colletweldedtoworksurface.
把夹持器焊在工件外表了
Remedy:
•Checkpressedair.
措施:
检查压缩空气供给装置
•Checkcablepackage.
检查管线总成
•Checkweldhead-sliderailmotion.
检查焊头运动滑轨
•Checkorreplaceweldhead.
检查或更换焊头
•Checkfeeder.
检查送料器
•CheckfeederfusesF1-F3.
检查送料器保险丝F1-F3
•Resetfault.
故障复位
•Replacecollet.
更换夹持器
•Notifyserviceengineer!
专业人员处理
Fault5:
“Weldproceduresequencefault“
故障5:
焊接程序顺序故障
E*planation:
Duetoamalfunctiontheweldsequenceisnotterminatedcorrectly.
解释:
由于一个错误功能使焊接过程没有按照程序进展到底
Cause:
•FeederorSMPSmalfunction.
原因:
送料器或电源故障
Remedy:
•Resetfault.
措施:
故障复位
•Checkwelding(ifnecessaryrepeatwelding).
检查焊接〔重新焊接〕
•Notifyserviceengineer!
专业人员处理
Fault6:
“Programnoselected“
故障6:
缺少程序
E*planation:
Theweldunitdoesnotdetectanyprogramnumber.
解释:
焊接单元不识别程序
Cause:
•Programno.is0.
原因:
程序为0
•Transfersignalhasnotbeenset.
没有设置承受信号
•Datalinedefective.
数据线被损坏了
Remedy:
•Customerinterface(orinterfaceprogram)mustbeverified.
措施:
检查用户接口〔或接口程序〕是否编写
•Notifyserviceengineer!
专业人员处理
Fault7:
“Programnotactive“
故障7:
程序没有激活
E*planation:
Theselectedweldprogramisnotactiveandthereforecannotbee*ecuted.
解释:
由于被选择的焊接程序没有被激活,因此无法实施焊接
Cause:
•Weldunitincorrectlyprogrammed.
原因:
焊接单元程序编写错误
•Faultcustomercontrol.
用户控制端错误
•Datalinedefective.
数据线被损坏了
Remedy:
•Checkweldprogramandactivateorselectanactiveweldprogram.
措施:
检查焊接程序并激活或者选择一个已经激活的程序
•Notifyserviceengineer!
专业人员处理
Fault13:
“SMPS:
Liftfault“
故障13:
电源:
没有拉弧
E*planation:
Weldunitisunabletoidentifyliftviameasurementlines.
解释:
焊机通过它的测量线不能确定拉弧过程
Cause:
•Incorrectlysequenceofliftmovement.
原因:
拉弧过程的顺序不正确
•Weldconditionsprohibitlift.
焊接条件阻碍了拉弧
•Cablepackagedefective.
管线总成损坏
•Weldheaddefective.
焊头被损坏
•Defectivefeeder.
送料器被损坏
•Internalprocesscyclefault.
设备内部运行故障
Remedy:
•Checkweldconditions.
措施:
检查焊接条件
•Checkweldhead.
检查焊头
•Checkfeeder.
检查送料器
•Studfeeding.
送一次钉
•Checkfeederconnection.
检查送料器连接线
•Repeatweldcycle.
重复一次焊接
•ForcedWC.
启动焊接完成信号
•Notifyserviceengineer!
专业人员处理
Fault15:
“Dropdowntimeout“
故障15:
下落时间超时
E*planation:
Ma*.droptimewase*ceededandweldingwasstopped.
解释:
下落时间超出最大允许值,焊接被中断
Cause:
•Airgapincorrectlyadjusted.
原因:
间隙调整错误
•Weldcircuitresistancetoohigh.
焊接回路电阻过高
•Measurementline-groundmissing.
没有连接地线测量线
•SKK/PKdefective.
自动焊头或焊枪损坏
Remedy:
•Resetfault.
措施:
故障复位
•checkmeasurementline(ifnecessary,reduceweldcircuitresistance)
检查测量线〔降低焊接回路电阻值〕
•ChecksettingofSKK-/PK.
检查自动焊头或焊枪状态
•Notifyserviceengineer!
专业人员处理
Fault16:
“Opencircuit,noarc“
故障16:
空载焊接
E*planation:
E*tinguishingofthearcduringweld,resp.theweldcurrentisbelowI=80A.
解释:
焊接过程中拉弧被断开,或焊接回路电流小于80A
Cause:
•Airgaptoolarge.
原因:
间隙过大
•Gunwasremovedatthebeginningoftheweld.
焊枪在开场焊接时被提起
•E*tremelyimpureworksurface.
焊接外表油污太多
•FaultSMPS.
电源故障
Remedy:
•Repeatweldcycle.
措施:
重复一次焊接
•Studfeeding.
送一次钉
•Checkadjustingoftheweldgun.
检查焊枪的调整
•Checkweldingconditions.
检查焊接条件
•Checkworkpiececonditions.
检查工件外表
•Notifyserviceengineer!
专业人员处理
Fault17:
“Measurementlinebroken“
故障17:
测量线中断
E*planation:
Measurementlinesignalnotanylongerdetected.
解释:
测量线信号没有被捕捉到
Cause:
•Measurementlinebrokenorincorrectlyconnected.
原因:
测量线损坏或连接错误
•Reversedmeasurementline-groundandmeasurementline.
地线测量线和测量线接反了
•SOWpowerfailure.
和工件的接触电压中断
•Weldlineinterrupted.
焊接电缆中断
Remedy:
•Checkfusesonfrontpanel.
措施:
检查面板上的保险丝
•Resetfault.
故障复位
•Checkweldingcable.
检查焊接线
•Checkmeasuringline.
检查测量线
•Checkground-measurementline
检查地线测量线.
•Checkfeederfuses.
检查送料器的保险丝
•Notifyserviceengineer!
专业人员处理
Fault23:
“Handgunsequencenotfollowed“
故障23:
手枪焊接启动条件
E*planation:
Correctsequencewhenweldingwithagun(PK/PLM)wasnotobserved.
解释:
在用手枪焊接时没有遵守正确的焊接顺序
Cause:
•Angularityswitchby-passedorincorrectlyadjusted.
原因:
角度开关被桥接或调整错误
•Triggerstartby-passed.
启动开关被桥接
•Correctsequence"SOW-ANG-START"notobserved.
没有遵守SOW(接触信号)-WS(角度开关)-START(焊接)的焊接顺序
Remedy:
•Observesequence"SOW-ANG-START".
措施:
遵守SOW(接触信号)-WS(角度开关)-START(焊接)的焊接顺序
•CheckPKforcorrectsettingofangularity.
检查角度开关的调整情况
•Releasetriggerandrestart.
松开启动开关并重新启动
•Notifyserviceengineer!
专业人员处理
Fault25:
“Wrongstudloaded“
故障25:
焊钉输送错误
E*planation:
Thesuppliedstudisnotthespecifiedstudrequiredbyunitcontrol.
解释:
所提供的焊钉不是焊机指定的焊钉
Cause:
•Theweldunitidentifiedanincorrectstudintheweldheadviatheliftmeasuringsystemorthestudverificationtest.
原因:
焊机只识别通过拉弧测量系统或者通过焊钉检验的焊钉的焊头
Remedy:
•Resetfault.
措施:
故障复位
•Repeatstudfeeding.
重新送一次钉
•Verifycorrectstudlengthinthefeeder.
检验送料器里焊钉的长度
•Checkprogramming.
检查程序
Fault30:
“Weldoutoftolerance〞
故障30:
焊接参数超差
E*planation:
Collectivefaultforthee*ceededtolerances.
解释:
一般性超差
Cause:
•Thefollowingtolerancesareoutofparameter:
weldcurrent,weldtime,Vp,Vw,Pen,Varcpeak,Varcdroporweldenergy.
原因:
超出公差的参数:
焊接电流,焊接时间,拉弧电压,焊接电压,焊接深度,电压峰值,电压降或焊接能量
•DefectiveSMPSorweldingtool.
电源或焊接工具损坏
Remedy:
•Resetfault.
措施:
故障复位
•Checktolerances.
检查公差设定值
•Checkweldcircuitandweldconditions.
检查焊接电流和焊接条件
•CheckSMPSandweldingtool.
检查电源和焊接工具
Fault100:
“Feeder:
Nopowertoau*.supply“
故障100:
送料器:
没有电压
E*planation:
Thefeederidentifiesnovoltagesupply.
解释:
送料器没有电压供给
Cause:
•Defectivefeederfuse.
原因:
送料器保险丝损坏
•Defectivefeeder.
送料器损坏
Remedy:
•Replacefeederfuse.
措施:
更换送料器保险丝
•Checkfeeder.
检查送料器
•Notifyserviceengineer!
专业人员处理
ault102:
“Feeder:
Feedrailnotfilledintime“
故障102:
送料器:
焊钉传送错误
E*planation:
Fillingoftherailwayisnotensured.
解释:
焊钉传送过程中出现故障
Cause:
•Sufficientstudlevelintheseparatingdrumnotreached.
原因:
焊钉卡在了滑道上
•Mechanicaldefectoftheescapementrails
滑道上有机械故障
•Wrongadjustingonthestudinletdish.
焊钉口调整错误
•Wrongadjustedordefectivepro*imityswitch"Min".
最小接近开关调整错误或损坏
Remedy:
•Checkadjusting.
措施:
检查送料器调整
•Replenishweldstuds.
加满焊钉
•Removeblockage.
去除滑道上焊钉
•Adjustpro*imityswitchor/andreplace.
调整接近开关或更换
•Notifyserviceengineer!
专业人员处理
Fault106:
“Feeder:
Feedtubelockingswitchopen“
故障106:
送料器:
送料管被锁紧
E*planation:
Thesignalforfeedhoselockingatthestudfeederisnotconfigured.
解释:
送料器锁紧信号开关没有被盖上
Cause:
•Feedtubenotconnected(gun).
原因:
送料管没有连接
•Nobridgeforfeedtubelocking(head).
送料管锁紧开关没有连上
•Defectivecablepackage.
管线总成损坏
•DefectivefuseF5onPCBETFCPUE510.
中央处理器E510电路板保险丝F5损坏
Remedy:
•Connectingfeedtube.
措施:
连接送料管
•Checklockingswitch.
检查紧锁开关
•Checkcablepackage.
检查管线总成
•Replacefuse.
更换保险丝
•Notifyserviceengineer!
专业人员处理
Fault109:
“Feeder:
Feedcycletimeout“
故障109:
送料器:
送料循环超时
E*planation:
Theweldunitindicatesanincorrectlyperformedfeedcycle.
解释:
焊机显示一个错误的送料循环
Cause:
•Thefeederdoesnotterminateafeedcycleinthema*imum
monitoringtime.
原因:
送料器没有把送料循环锁定在最大的监控时间内
Remedy:
•Checkfeeder.
措施:
检查送料器
•Repeatstudfeeding.
重复一次焊接
•Notifyserviceengineer!
专业人员处理
Fault118:
“Feeder:
+5VKeypadnotdetected“
故障118:
送料器:
控制面板没有+5V电压供给
E*planation:
Thevoltagesupply5Vforthekeypadmunicationismissing.
解释:
控制面板通信的+5V电压没有
Cause:
•DefectivefuseF3onPCBETFCPUE510.
原因:
中央处理器E510电路板保险丝F3损坏
•DefectiveoptocoupleronthePCBETFCPUE510.
E510电路板上的光耦合器损坏
Remedy:
•Replacefuse.
措施:
更换保险丝
•ReplacePCBETFCPUE510.
更换E510电路板
•Notifyserviceengineer!
专业人员处理
Fault119:
“Feeder:
LM/Solenoidundervoltage“
故障119:
送料器:
自动焊枪/电磁阀缺乏
E*planation:
Thevoltagesupplyforthelinearmotor/solenoidislessthan90Volt
解释:
直流电机/电磁阀的供电电压低于90V
Cause:
•DefectivefuseF2onETFPCBAmplifierE512.
原因:
放大器E512电路板保险丝F2损坏
•DefectiveETFPCBamplifierE512.
放大器E512电路板损坏
Remedy:
•ReplacefuseF2.
措施:
更换保险丝F2
•ReplaceETFPCBAmplifierE512.
更换放大器E512电路板
•Notifyserviceengineer!
专业人员处理
Fault121:
“Feeder:
LM/Solenoidovervoltage“
故障121:
送料器:
自动焊枪/电磁阀电压超出
E*planation:
T