思科路由的26个大体实验.docx
《思科路由的26个大体实验.docx》由会员分享,可在线阅读,更多相关《思科路由的26个大体实验.docx(37页珍藏版)》请在冰豆网上搜索。
思科路由的26个大体实验
cisconet实验一修改cisco路由器的名称及路由器密码命令操作
实验要求:
1.路由器名:
cisconet
2.设置password为cisconet,secret为cisconet,vty为cisconet,
3.并要求所有密码都加密。
实验进程:
cisconet> enable
cisconet# configure terminal
cisconet(config)#hostname cisconet 设置路由器名
cisconet(config)# enable password cisconet 设置password
cisconet(config)# enable secret cisconet 设置secret
cisconet(config)# line vty 0 4
cisconet(config-line)#login 要求密码验证
cisconet(config-line)#password cisconet 设置vty密码
cisconet(config-line)#exit 退出线路配置模式
cisconet(config)#service password-encryption 对密码加密
cisconet实验二配置路由器端口ip地址/标识及保留当前的配置操作
实验要求:
1:
在路由器的端口下配置ip地址
掩码 2:
配置路由器提示信息 welcome to cisconet cisconet lab
3:
配置路由器接口提示信息 this is a serial port
4:
保留当前的配置
cisconet>enable
cisconet# configure terminal
cisconet(config)# interface fastethernet 0/0
cisconet(config-if)# ip address
对以太网口fa0/0配置IP
cisconetkeji(config-if)# no shutdown 开启端口
cisconet(config-if)exit
cisconet(config)#banner motd “
cisconet(config)#welcome to cisconet cisconet lab” 提示信息
以上几部是设置登岸提示信息
cisconet(config)# interface serial 0
cisconet(config-if)# description this is a serial port 端口描述信息
cisconet(config-if)#end
cisconet#copy running-config startup-config 对配置进行保留
cisconet实验三CDP命令操作
实验要求:
1.路由器名:
cisconet一、 cisconet二、 cisconet3.
2.设置password为cisconet,secret为cisconet,vty为cisconet,,并要求所有密码都加密.
3.配置各路由器.
实验进程:
配置路由器1
router(config)#hostname cisconet1 设置路由器名
cisconet1(config)enable password cisconet 设置password
cisconet1(config)enable secret cisconet 设置secret
cisconet1(config)line vty 0 4
cisconet1(config-line)#login 要求密码验证
cisconet1(config-line)#password cisconet 设置vty密码
cisconet1(config-line)end
cisconet1(config)#service password-encryption 对密码加密
cisconet1(config)#interface serial 0
cisconet1(config-if)#ip address 设置s0的IP地址和子网掩码
cisconet1(config-if)#clock rate 56000 设置时钟频率
cisconet1(config-if)#no shutdown 开启端口
路由器2和路由器3的配置和路由器1类似,只是各接口的IP地址设置不同,同时要
在路由器3的serial 1接口上配置时钟频率,而路由器2的两个接口上不需配置时钟.
在路由器2上操作:
cisconet2#show cdp 显示CDP信息
cisconet2#show cdp neighbors 显示相连的CDP邻居汇总信息
cisconet2#show cdp neighbor detail 显示相连的CDP邻居详细信息
cisconet2#show cdp traffic 显示CDP所用的数据包的信息
cisconet2#show cdp entry * 显示所有相邻路由器的所有信息
cisconet2#show cdp entry cisconet1(路由器名) 显示特定邻居(cisconet1)的详细信息
cisconet实验四环回接口的利用和创建
实验要求:
1.路由器名为cisconet,通过路由器的CONSOLE口直接用反线与PC上的COM口相连;
2.在路由器上将密码设置为cisconet后,保留配置;
3.从头启动路由器将密码破解.
实验进程:
在cisconet上的配置:
router(config)#hostname cisconet 将路由器名设置为cisconet
cisconet(config)#enable secret cisconet 设置路由器的特权密码
cisconet(config)exit
cisconet#copy running-config startup-config 保留配置
cisconet#reload 从头启动路由器
从头启动是按键盘的CTRL+BREAK键,进入ROMMON模式
> o/r 0x2142 更改寄放器的值,使路由器启动后直接进入会话模式
> i 从头启动路由器
路由器启动直接进入会话模式后,不进行任何配置,进入IOS
router#copy startup-config running-config 将配置载入到RAM中
cisconet#configure terminal
cisconet(config)#no enable secret 删除密码
cisconet(config)exit
cisconet#copy running-config startup-config 保留配置
从头启动再进入特权模式就再也不需要密码了
cisconet实验五配置TELNET远程登岸
实验要求:
1.路由器命名为cisconet1和cisconet2;
2.在cisconet2上设置特权密码和VTY 密码;
3.从cisconet1上TELNET到cisconet2;
4.在cisconet2上查看已经TELNET到本设备上的其它用户。
实验进程:
Cisconet2上的配置
Cisconet2(cinfig)#password secret cisconet 设置特权密码
Cisconet2(cinfig)#line vty 0 4 进入线路配置模式
Cisconet2(cinfig-line)#password cisconet 设置VTY密码
Cisconet2(cinfig-line)#login 要求进行密码验证
Cisconet2(cinfig-line)#exit
Cisconet2(cinfig)#interface serial 0
Cisconet2(cinfig-if)#ip address 配置IP地址
Cisconet2(cinfig-if)#clock rate 72000 配置时钟频率
Cisconet2(cinfig-if)#no shutdown 启用接口
Cisconet1上的配置
Cisconet1(cinfig)#interface serial 0
Cisconet1(cinfig-if)#ip address 配置IP地址
Cisconet1(cinfig-if)#no shutdown 启用接口
配置完成后就可以够从cisconet1上TELNET到cisconet2对其进行控制管理.
Cisconet1(cinfig) #telnet 远程TELNET到cisconet2
登岸到cisconet2时按要求输入VTY密码和特权密码后完全登岸成功,
在cisconet2上利用show users 命令查看telnet到本设备的用户。
cisconet实验六环回接口的利用和创建
实验要求:
1.路由器名为cisconet1和cisconet2;
2.在每一个路由器上创建一个环回接口,并给其分派IP地址;
3.删除环回口
实验进程:
1.环回接口是路由器上的一个逻辑、虚拟接口。
路由器上默许没有任何环回接口,但能够创建,
正常情形下路由器的接口不像互换机那么多,有时在做某些实验时,比如在上面的拓扑图上
两个PC在做某些实验时能够通过创建两个loopback(环回)接口来代替。
loopback接口在路
由器上与物理接口一样对待,能够给他们分派寻址信息。
loopback接口利用普遍,因为该接口
默许是起用的,除非用shutdown命令关闭.
2.创建环回接口
cisconet1#configure terminal 进入全局配置模式
cisconet1(config)#interface loopback 0 创建loopback 0并进入接口配置模式
cisconet1(config-if)#ip address 给环回口分派IP地址
cisconet1(config-if)#end
cisconet1#show interface loopback 0 查看环回口信息
cisconet1#configure terminal
cisconet1(config)#no interface loopback 0 删除环回口
cisconet实验七静态路由和默许路由的配置
实验要求:
1.设置路由器名为cisconet一、cisconet二、cisconet3;
2.在路由器cisconet1和cisconet3上配置默许路由;
3.在cisconet2上配置静态路由;
4.设置PC的IP地址和默许网关.
Router(config)#hostname cisconet1 设置路由器名
Cisconet1(config)#interface ethernet 0 进入e0端口
Cisconet1 (config-if)#ip address 添加e0口的IP
Cisconet1 (config-if)#no shutdown 打开e0口
Cisconet1 (config-if)#exit
Cisconet1 (config)#interface serial 0 进入s0端口
Cisconet1 (config-if)#ip address 添加s0口的IP
Cisconet1 (config-if)#clock rate 56000 设置时钟
Cisconet1 (config-if)#no shutdown 打开s0口
Cisconet1 (config-if)#exit
Cisconet1 (config)#ip route 0.0.0.0 添加缺省路由
Router(config)#hostname cisconet2 设置路由器名
cisconet2 (config)#interface serial 0 进入s0端口
cisconet2 (config-if)#ip address 添加s0口的IP
cisconet2 (config-if)#no shutdown 打开s0口
cisconet2 (config-if)#exit
cisconet2 (config)#interface serial 1 进入s1端口
cisconet2 (config-if)#ip address 添加s1口的IP
cisconet2 (config-if)#no shutdown 打开s1口t
cisconet2 (config-if)#exit
cisconet2 (config)#ip route 添加静态路由
cisconet2 (config)#ip route 添加静态路由
Router(config)#hostbane cisconet3
cisconet3 (config)#interface ethernet 0 进入e0端口
cisconet3 (config-if)#ip address 添加e0口的IP
cisconet3 (config-if)#no shutdown 打开e0口
cisconet3 (config-if)#exit
cisconet3 (config)#interface serial 1 进入s1端口
cisconet3 (config-if)#ip address 添加s1口的IP
cisconet3 (config-if)#no shutdown 打开s1口t
cisconet3 (config-if)#exit
cisconet3 (config)#ip route 0.0.0.0 添加缺省路由
PC 上的配置为:
PC1:
IP为 网关:
:
IP为 网关:
实验八RIP动态路由的配置
实验要求:
1.路由器名为cisconet一、 cisconet2;
与PC1相连,cisconet2与PC2相连,cisconet1的so口与jiande2的so口相连;
3.各接口的IP地址如拓扑图所示,cisconet1为DCE,cisconet2为DTE;
4.在两路由器上起用RIP协议;
5.查看路由表并验证各网段之间的连通性.
实验进程:
1.按拓扑图的需要配置各路由器端口的IP地址,用no shutdown命令起用各端口;
2.在cisconet1的S0端口利用clock rate 64000命令配置时钟频率;
3.配置各PC的ip地址和默许网关;
4.在两路由器上利用show ip route命令查看路由表,只能看到与该路由器直连的网段;
5.起用RIP协议并将各网段加入路由进程
在cisconet1上:
cisconet1(config-router)#router rip 起用路由协议
cisconet1(config-router)#network 将网段加入路由进程
cisconet1(config-router)#network 将网段加入路由进程
cisconet1(config-router)#end
cisconet1#show ip route 查看路由表
在cisconet2上 cisconet1(config-router)#router rip 起用路由协议
cisconet1(config-router)#network 将网段加入路由进程
cisconet1(config-router)#network 将网段加入路由进程
cisconet1(config-router)#end
cisconet1#show ip route 查看路由表
配置RIP协议后,路由表中能够看到通过RIP协议学习到的非直连的网段的路由条款,
在PC1上利用PING 测试到PC2的连通性,测试成功。
cisconet实验九通过IGRP路由协议实现非等价带宽的负载均衡
实验要求:
1.路由器名为cisconet1和cisconet2;
2.两路由器用双绞线(10M)和串行线连接(1.544M);
3.在两路由器上创建两各环回接口模拟与路由器直连的PC机;
4.利用命令实现非等价负载均衡。
实验进程:
1.路由器cisconet1的配置
ci