电池参考规格书00WIPT000401.docx
《电池参考规格书00WIPT000401.docx》由会员分享,可在线阅读,更多相关《电池参考规格书00WIPT000401.docx(24页珍藏版)》请在冰豆网上搜索。
电池参考规格书00WIPT000401
File.No立项编号:
00WIPT0004-01
Version版本:
A/0
Date日期:
2012-11-20
Customer’sName客户名称:
Type(类型):
Li-ionPolymerBattery(锂离子电池)
Model(型号):
18650/4400mAh/7.4V
CustomerApproval
(客户确认)
CheckedBy/Date
审核/日期
ApprovedBy/Date
批准/日期
CompanyStamp
(公司印章)
SHENZHENWIPTENERGYTECHNOLOGYCO.,LTD
(深圳市沃普泰能源科技有限公司)
PreparedBy/Date
编制/日期
CheckedBy/Date
审核/日期
ApprovedBy/Date
批准/日期
楚鹏
2012/11/20
/
Address:
5Building,WuwuScienceandTechnology网址(Website):
Park,LonghuaTown,BaoanDistrict,Shenzhen电话(Tel):
+86-755-23469919
地址:
深圳市宝安区龙华镇伍屋科技园5栋传真(Fax):
+86-755-223469909
AmendmentRecords
(修正记录)
Edition
(版本)
Description
(记述)
Preparedby
(编制)
Approvedby
(批准)
Date
(日期)
A/0
FirstEdition
首次发行
ProductSummary产品概要
1、Scopeandstandard适用范围及依据标准
1.1Scope适用范围
ThisspecificationisappliedtobatterymanufacturedbyShenzhenWiptElectronicsCo.,Ltd.
本产品规格书适用于深圳市沃普泰能源科技有限公司提供的锂离子电池。
1.2Standard依据标准
本产品依据标准:
中华人民共和国国家标准GB/T18287-2000《蜂窝电话用锂离子电池总规范》。
ThisproductcomplieswithNationalStandardGB/T18287-2000“CellPhoneLithium-ionBatteryGeneralSpecifications”ofPRC.
2、Productiondescription产品描述
2.1Name名称:
Li-ionBattery(锂离子电池)
2.2Mode型号:
18650/4400mAh/7.4V
2.3Cell采用电芯:
18650/2200mAh/3.7V
2.4StructureDrawing电池结构图:
(mm)
图示只标识沃普泰设计尺寸。
2、Specification主要技术参数
NO序号
Items项目
Parameter参数
Remarks备注
2.1
RatedCapacity
标称容量
4400mAh
Discharge:
0.2C
放电
cut-offvoltage:
5.6V
截止电压
MinimumCapacity
最小容量
4360mAh
2.2
Energy能量
32.56Wh
2.3
NominalVoltage
标称电压
7.4V
2.4
OpenVoltage
出厂电压
7.2V~7.8V
2.5
LoadVoltage负载电压
≥7.2V
10Ω
2.6
InternalImpedance内阻
≤200mΩ
AC1KHzafterstandardcharge
标准充电后AC1KHz测试
2.7
Chargevoltage充电电压
8.4V
2.8
Standardchargecurrent
标准充电电流
2200mA
0.5C
2.9
Maxchargecurrent
最大充电电流
4400mA
1.0C
2.10
Standarddischargecurrent
标准放电电流
880mA
0.2C
2.13.75
Maxdischargecurrent
最大放电电流
4400mA
1.0C
2.12
Dischargecut-offvoltage
放电截止电压
5.6V
2.13
OperatingTemperature
工作温度
0~+45℃
Charge充电
-20~+60℃
Discharge放电
2.14
StorageTemperature
贮存温度
-20℃~+60℃
Lessthan1month
小于一个月
-20℃~+30℃
Lessthan6months
小于六个月
2.15
Weight重量
About180g
3.Batteryconfiguration电池组成
NO
序号
Item
项目
Criteria
标准
Remarks
备注
3.1
Cell电芯
18650/2200mAh/3.7V
3.2
PCM保护板
WIPT-2S-G2N+MOS1870
2S
3.3
Breaker温度开关
/
3.4
PTC自恢复保险丝
/
4.BatteryPerformanceTest电池性能检查及测试
4.1Appearance外观和结构
Thereshallbenosuchdefectasscratch,burandothermechanicalscratch,andtheconnectorshouldbenorustdirt.Thestructureanddimensionsseeattacheddrawingofthebattery.
电池的表面应无明显的划痕毛刺及其其它机械划伤,外露的金属端子应无锈蚀污垢。
结构尺寸见电池的外形尺寸图。
(见附件:
电池结构图)
4.2TestEquipment测试设备要求
(1)DimensionMeasuringInstrument尺寸测量设备
Thedimensionmeasurementshallbeimplementedbyinstrumentswithaccuracynolessthan0.01mm.
测量尺寸的仪器的精度应不小于0.01mm
(2)Voltmeter电压表
Classwithnationalstandardormoresensitiveclasswithinnerimpedancenotlessthan10KΩ/V.
国家标准或更灵敏等级,内阻不小于10KΩ/V.
(3)Ammeter电流表
Classwithnationalstandardormoresensitiveclass.Totalexternalresistanceincludingammeterandwireislessthan0.01Ω.
国家标准或更灵敏等级,外部总体内阻包括电流表和导线应小于0.01Ω.
(4)ImpedanceMeter内阻测试仪
ImpedanceshallbemeasuredbyaACimpedancemethod(AC1kHzLCRmeter).
内阻测试仪测试方法为交流阻抗法(AC1kHzLCR).
4.3StandardTestCondition标准的测试条件
Testshouldbeconductedwithnewbatterieswithinonemonthaftershipmentfromourfactoryandthecellsshallnotbecycledmorethanfivetimesbeforethetest.Unlessotherwisedefined,testandmeasurementshallbedoneundertemperatureof20±5℃andrelativehumidityof45~85%.
测试电池必须是本公司出厂时间不超过一个月的新电池,且电池未进行过五次以上充放电循环。
除非其它特殊要求,本产品规格书规定的测试的环境条件为:
温度20±5℃,相对湿度45%~85%。
4.4StandardCharge标准充电
0.5C=2200mAFullchargecondition:
Constantcurrent0.5C,Constantvoltage8.4Vfor4hoursinallat20±5℃.
0.5C=2200mA8.4V(CC-CV)总充电时间不超过4小时,其中在20±5℃环境下充电。
4.5CommonPerformance产品的常规性能
No
Items/项目
Testingmethodanddeterminantstandard/测试方法和判定标准
1
ChargePerformance
充电性能
Thebatterycanbechargedwhenusingtheoriginalcharger.Thestandardchargemode:
underthetemperatureof20±5℃,chargethebatterywiththecurrentof0.2Cuntilthevoltagereachesupto8.4V,thenchargewithconstantvoltageuntilthechargecurrent≤0.05C,thenstopcharging.
使用原装充电器能够充电。
标准充电模式:
在20±5℃条件下,电池用0.2C充电,当电池电压达到8.4V时改为恒压充电,直到充电电流小于或等于0.05C时停止充电。
2
DischargePerformance
放电性能
Whenconnectingwithload,thebatterycansupplypower.Chargethebatterywithstandardchargemode,thenrestfor0.5h,thendischargewith1Cuntilthevoltageis5.6V,andthedischargetimeisrequired≥51min.
电池外接负载能够供电。
将电池按标准充电模式充好电后,开路搁置0.5h,再以1C放电至5.6V,要求放电时间≥51min。
3
CyclePerformance
循环寿命
Underthetemperatureof20±5℃,chargethebatterywith0.2C,whenthevoltagereachesupto8.4Vchargewithconstantvoltageuntilthechargecurrent≤20mA,thenstopcharging,restfor0.5h,thendischargewith0.2Cto5.6V.Cyclewiththeabovemode,whenthecontinuousdischargetime<60%stopcycling.Thecyclelifeisrequired≥300times.
在20±5℃条件下电池按0.2C充电,当电压达到8.4V时改为恒压充电,直到充电电流小于或等于20mA时停止充电,静置0.5h后,0.2C放电至5.6V的方式进行循环,当连续三次放电容量<初始容量60%时寿命为终止,要求循环寿命≥300次.
4
ChargedStorageCharacteristics
荷电保持能力
Chargethebatterywith0.2C,thenshifttochargewithconstantvoltageuntilthevoltagereachesupto8.4V,whenthechargecurrent≤0.05Cstopcharging;restunderthetemperatureof20±5℃for28dthendischargewith0.2Cto5.6V.Thedischargetimeisrequired≥4.25h.
电池按0.2C充电,当端电压达到8.4V时改为恒压充电,充电电流小于或等于0.05C时,充电停止;将电池开路放置在20±5℃条件下28天后,以0.2C放电至5.6V,要求放电时间≥4.25h。
5
StorageCharacteristics
存放性能
Chargethebattery,whichisnewlymanufacturedshorterthan3months,with0.5Cuntilthecapacityreachesto40~50%,afterrestingfor12monthsunderthetemperatureof20±5℃andthehumidityof45~75%,thenchargewith0.2Cto8.4Vthenshifttochargewithconstantvoltage,afterfull-chargerestfor0.5h,thendischargewith0.2Cto5.6V.Thedischargetimeisrequired≥4h.将生产日期到实验日期不足3个月的电池按0.5C充入40~50%容量后,放置在温度20±5℃﹑湿度为45~75%的环境中开路存放12个月后,电池按0.2C充电至8.4V时改为恒压充电,充饱后;静置0.5h,再以0.2C放电至5.6V,要求放电时间≥4h。
4.6SafetyPerformance产品可靠性
No
Items/项目
Testmethodanddeterminantstandard/测试方法和判定标准
1
HighTemperatureCharacteristics
高温性能
Underthetemperatureof20±5℃,afterchargingthebatterywith0.2C,thenputthebatteryintotheconstanttemperatureandhumidityovenwith55±2℃for2h,thendischargewith1Cto5.6V.Thedischargetimeisrequired≥51minandthebatteryshouldnodeformationandsmoking.
在20±5℃条件下,电池按0.2C充电结束后,将电池放入55±2℃的恒温恒湿箱中恒温2h后,然后以1C电流放电至5.6V,要求放电时间≥51min,且电池外观无变形、冒烟。
2
LowTemperatureCharacteristics
低温性能
Underthetemperatureof20±5℃,afterchargingthebatterywith0.2C,thenputthebatteryintotheconstanttemperatureandhumidityovenwith-10±2℃for16~24h,thendischargewith0.2Cto5.6V.Thedischargetimeisrequired≥3handthebatteryshouldnodeformationandsmoking.
在20±5℃条件下,电池按0.2C充电结束后,将电池放入-10±2℃的恒温恒湿箱中恒温16~24h,然后以0.2C电流放电至5.6V,要求放电时间≥3h,且电池外观无变形、冒烟。
3
OverchargeProtection
Characteristics
过充电
保护性能
Afterfull-chargingthebatterywith0.2Candset2timesofthenominalvoltageandcurrentasconstantcurrentandvoltagesupply,thenloadittothebatteryfor8h.Itisrequiredthebatteryshouldbenoleakage,deformation,smokingandexplosionduringthetestprocesses.
电池按0.2C充满电后,再将恒流恒压源设定为2倍标称电压﹑电流,然后加载于电池上8h,要求试验过程中电池不漏液、变形、冒烟和爆炸。
4
Over-dischargeProtection
Characteristics
过放电
保护性能
Underthetemperatureof20±5℃,afterdischargingthebatterywith0.2Cto5.6V,thenconnecttheloadwith30Ωanddischargefor24h.Itisrequiredthebatteryshouldbenoleakage,fire,smokingandexplosionduringthetestprocesses.
在20±5℃条件下,电池按0.2C放电至5.6V后,外接30Ω负载再放电24h,要求实验过程中电池不漏液、起火、冒烟和爆炸
5
Short-circuitProtection
Characteristics
短路保护
性能
Underthetemperatureof20±5℃,afterfull-chargingthebatterywith0.2C,thenmakethebattery’sanodeandcathodeshort-circuitfor1h(theconnectingresistanceissmallerthan100mΩ),thencuttheanodeandcathode,afterthebatterymomentarychargeby1Ccurrent,thevoltageshouldcomebackto7.2V,andthereshouldbenoleakage,deformation,smokingandexplosionduringthetestprocesses.
在20±5℃条件下,电池按0.2C充满电后,将电池正负极短路(外接电阻小于100mΩ)持续1h,再将电池正负极断开,电池以1C瞬时充电后电压应不小于7.2V,且试验过程中电池不漏液、变形、冒烟和爆炸。
6
ConstantHumidityandTemperatureCharacteristics
恒定湿热性能
Underthetemperatureof20±5℃,afterchargingthebatterywith0.2C,thenputthebatteryintotheconstanttemperatureandhumidityovenwith10±2℃and90~95%for48h,thebatteryshouldbenoobviousdeformation,leakage,rust,smokingandexplosion.Aftertestingtakeoutthebatterythenrestfor2hunderthetemperatureof20±5℃,dischargewith1Cto5.6V.Thedischargetimeisrequired≥36min.
在20±5℃条件下,电池按0.2C充电结束后,放入40±2℃,湿度90~95%的恒温恒湿箱内48h,电池应无明显变形、漏液、生锈、冒烟或爆炸,试验结束后将电池取出搁置2h,在20±5℃条件下,以1C放电至5.6V,要求放电时间≥36min。
7
DropTest跌落实验
Underthetemperatureof20±5℃,afterfull-chargingthebatterywith0.2C,thendropitfreelyfrom1meterheightontothehardboardwhich18~20mmthick(6timeseachofX,Y,Zwithpositiveandnegativedirections).Thebatteryshouldbenosmokingandexplosion,Aftertestdischargethebatterywith1C,andthedischargetimeisrequired≥51min(Thebatteryshouldbecyclednomorethan3times,amongthemifonetimeispassedthenstop.).
在20±5℃条件下,电池按0.2C充满电后,将电池从1米高度自由跌落至厚度为18~20mm的硬木板上(X、Y、Z正负方向6个方向每个方向分别朝下跌落一次)电池应不冒烟、爆炸,试验结束后,将电池进行1C放电性能测试,要求放电时间≥51min(最多可进行3次循环,其中任何一次合格即可停止)。
4.7Re