新格林耐特配置命令Word文件下载.docx
《新格林耐特配置命令Word文件下载.docx》由会员分享,可在线阅读,更多相关《新格林耐特配置命令Word文件下载.docx(9页珍藏版)》请在冰豆网上搜索。
4.TiNet#load?
application下载应用程序
configuration下载配置文件
keyfile下载SSH密钥文件
whole-bootrom下载全部的bootrom/设备升级命令/
5.TiNet(config)#ipaddress192.168.1.5255.255.255.0192.168.1.1
/配置交换机IP地址/
6.TiNet(config)show?
/show命令,后可以打问号/
Showip
Showmac
Showinterface
Showvlan
7.TiNet(config)#vlan3901/建立VLAN3901/
TiNet(config-if-vlan)#switchportethernet0/1/把端口1加入该VLAN/
TiNet(config)#ipvlan3901/定义管理vlan为3901
TiNet(config)#noipvlan1/删除默认管理VLAN1/
8.TiNet(config)#vlan1001-1512/批量建立VLAN/
9.TiNet(config-if-vlan)#switchportethernet0/2toethernet0/8ethernet0/11ethernet0/16
/在某一VLAN中或者VLAN段中批量加入端口/
10.TiNet(config-if-ethernet-0/16)#tagvlan1001,1112-1512,4000
/端口下批量打tag/
11.TiNet(config-if-ethernet-0/1)#switchportmodetrunk
/改变端口模式,为trunk模式/
12.TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall
/端口为trunk模式,允许所有VLAN通过/
13.TiNet(config-if-ethernet-0/2)#switchportaccessvlan1001
/改变端口PVID/
14.TiNet(config)#port-isolationethernet?
STRING<
3-4>
端口号为槽端口号<
0-2>
/端口号<
1-24>
TiNet(config)#port-isolationethernet0/2toe0/16
添加端口隔离下行端口成功./一步隔离,一条命令隔离除上行口以外所有端口/
15.TiNet(config)#interfacerangeethernet0/2toethernet0/16/批量端口处理命令/
16.TiNet(config-if-range)#bandwidth-control?
egress出口带宽控制
ingress入口带宽控制/端口限速命令/
17.TiNet(config)#showutilizationinterface/实时查看端口流量占比/
LinkUtilizationAveragesThuJan100:
43:
201970
portlinkReceivePeakRxTransmitPeakTx
Statuspkts/secpkts/secpkts/secpkts/sec
==================================================================
e0/1down0000
e0/2down0000
e0/3down0000
e0/4down0000
e0/5down0000
e0/6down0000
e0/7down0000
e0/8down0000
e0/9down0000
e0/10down0000
e0/11down0000
e0/12down0000
e0/13down0000
e0/14down0000
e0/15down0000
e0/16down0000
e1/1down0000
====spacebar->
togglescreenU->
pageupD->
pagedownCR->
exit====
通过空格键来切换回车键结束查看
18.TiNet(config)#usernamechange-passwo请输入您的登录密码:
******
请输入用户名(4--15位):
请输入新口令(1--15位):
********
输入确认口令(1--15位):
用户admin密码修改成功。
/修改登陆密码/
配置案例:
小河区某小区格林耐特设备配置
简要流程
TiNet(config)#ipaddress119.1.176.185255.255.255.0119.1.176.1/配置ip地址/
ConfigIPsuccessfully.
TiNet(config)#showip
Switchconfiguration
ipobtained:
MANUAL
ipaddress:
119.1.176.185
netmask:
255.255.255.0
gateway:
119.1.176.1
ManageVLAN:
1
MACaddress:
00:
0a:
5a:
11:
ba:
b8/查看交换机ip地址/
TiNet(config)#ex
TiNet#terminallanguagechinese/更改语言模式为中文/
TiNet(config)#vlan3901/建立vlan3901/
TiNet(config-if-vlan)#switchportall/在vlan3901下添加端口/
添加VLAN端口成功!
TiNet(config)#ipaddressvlan3901/定义交换机管理vlan/
配置管理VLAN成功!
交换机的配置信息
IP地址获得方式:
IP地址:
子网掩码:
网关地址:
管理VLAN:
13901/此时管理vlan为1和3901/
MAC地址:
b8
TiNet(config)#noipaddressvlan1/删除交换机默认管理vlan1/
删除管理VLAN成功!
3901
b8/管理vlan已改为3901/
TiNet(config)#interrangeethernet0/1toethernet0/16/批量进入端口1-16
TiNet(config-if-range)#tagvlan3901/端口1-16tagvlan3901/
TiNet(config-if-range)#ex
TiNet(config)#vlan1001/建立vlan1001/
TiNet(config-if-vlan)#switchportethernet0/1/vlan1001中加入端口1/
TiNet(config-if-vlan)#showvlan1001
显示VLAN信息
VLANID:
1001
VLANstatus:
static
VLANmember:
e0/1.
Statictaggedports:
StaticuntaggedPorts:
Dynamictaggedports:
TiNet(config)#vlan1015-1030/批量建立vlan1015-1030/
TiNet(config-if-vlan)#switchportethernet0/1ethernet0/16
/vlan1015-1030加入端口1-16/
TiNet(config-if-vlan)#showvlan1015
1015
e0/1,e0/16.
TiNet(config)#port-isolationethernet0/2toe0/16/端口2-16进行隔离,1口为上行口,未隔离/
添加端口隔离下行端口成功.
TiNet(config-if-ethernet-0/1)#switchport?
accessaccess端口
backup配置备份端口
mode端口模式
trunktrunk端口
TiNet(config-if-ethernet-0/1)#switchportmodetrunk
/更改端口1模式为trunk/
TiNet(config-if-ethernet-0/1)#switchporttrunkallowedvlanall
/允许所有vlan通过1口/
TiNet(config-if-ethernet-0/1)#switchporttrunknativevlan3901
/更改1口pvid为3901/
TiNet(config-if-ethernet-0/1)#ex
TiNet(config)#showutilizationinterface/查看端口实时流量/
24:
371970