Proe绘图NC刀具文档.docx
《Proe绘图NC刀具文档.docx》由会员分享，可在线阅读，更多相关《Proe绘图NC刀具文档.docx（40页珍藏版）》请在冰豆网上搜索。
Proe绘图NC刀具文档
五、区域车削
5.1区域车削屏幕演示截图
5.2区域车削刀位文件
$$*Pro/CLfileVersionWildfire4.0-M140
$$->MFGNO/MFG0001
PARTNO/MFG0001
$$->FEATNO/24
MACHIN/UNCX01,1
$$->CUTCOM_GEOMETRY_TYPE/OUTPUT_ON_CENTER
UNITS/MM
TURRET/1
$$->CSYS/1.0000000000,0.0000000000,0.0000000000,0.0000000000,$
0.0000000000,1.0000000000,0.0000000000,0.0000000000,$
0.0000000000,0.0000000000,1.0000000000,0.0000000000
SPINDL/RPM,200.000000,CLW
RAPID
GOTO/17.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/15.5000000000,0.0000000000,1.5000000000
GOTO/15.5000000000,0.0000000000,-102.5857864376
GOTO/16.6000000000,0.0000000000,-102.5857864376
RAPID
GOTO/16.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/14.5000000000,0.0000000000,1.5000000000
GOTO/14.5000000000,0.0000000000,-71.4400956940
GOTO/15.4952229178,0.0000000000,-83.8803821666
GOTO/16.5952229178,0.0000000000,-83.8803821666
RAPID
GOTO/16.5952229178,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/13.5000000000,0.0000000000,1.5000000000
GOTO/13.5000000000,0.0000000000,-58.9400956940
GOTO/14.5000000000,0.0000000000,-71.4400956940
GOTO/15.6000000000,0.0000000000,-71.4400956940
RAPID
GOTO/15.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/12.6986627382,0.0000000000,1.5000000000
GOTO/12.6986627382,0.0000000000,0.2418660249
GOTO/12.8068605844,0.0000000000,0.1728267622
CIRCLE/12.0000000000,0.0000000000,-1.0916794644,$
0.0000000000,1.0000000000,0.0000000000,1.5000000000
GOTO/13.5000000000,0.0000000000,-1.0916794644
GOTO/14.6000000000,0.0000000000,-1.0916794644
RAPID
GOTO/14.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/11.8973254764,0.0000000000,1.5000000000
GOTO/11.8973254764,0.0000000000,0.7531861258
GOTO/12.6986627382,0.0000000000,0.2418660249
GOTO/13.7986627382,0.0000000000,0.2418660249
RAPID
GOTO/13.7986627382,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/11.0959882146,0.0000000000,1.5000000000
GOTO/11.0959882146,0.0000000000,1.2645062267
GOTO/11.8973254764,0.0000000000,0.7531861258
GOTO/12.9973254764,0.0000000000,0.7531861258
RAPID
GOTO/14.6000000000,0.0000000000,0.7531861258
RAPID
GOTO/14.6000000000,0.0000000000,-29.0000000000
FEDRAT/150.000000,MMPM
GOTO/13.5000000000,0.0000000000,-29.0000000000
GOTO/13.4733969043,0.0000000000,-29.2812500000
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,78.5000000000
GOTO/12.7905841138,0.0000000000,-33.4702790521
GOTO/12.7905841138,0.0000000000,-54.5297209479
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,78.5000000000
GOTO/13.4733969043,0.0000000000,-58.7187500000
GOTO/13.4952229178,0.0000000000,-58.8803821666
GOTO/14.5952229178,0.0000000000,-58.8803821666
RAPID
GOTO/14.5952229178,0.0000000000,-33.4702790521
FEDRAT/150.000000,MMPM
GOTO/12.7905841138,0.0000000000,-33.4702790521
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,78.5000000000
GOTO/12.0811682275,0.0000000000,-44.0000000000
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,78.5000000000
GOTO/12.7905841138,0.0000000000,-54.5297209479
GOTO/12.3352494508,0.0000000000,-50.3107998539
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,78.5000000000
GOTO/13.4733969043,0.0000000000,-58.7187500000
GOTO/13.4952229178,0.0000000000,-58.8803821666
GOTO/15.4952229178,0.0000000000,-83.8803821666
GOTO/15.5000000000,0.0000000000,-84.0000000000
GOTO/15.5000000000,0.0000000000,-102.5857864376
GOTO/17.6000000000,0.0000000000,-102.5857864376
$$->END/
$$->FEATNO/298
$$->CSYS/1.0000000000,0.0000000000,0.0000000000,0.0000000000,$
0.0000000000,1.0000000000,0.0000000000,0.0000000000,$
0.0000000000,0.0000000000,1.0000000000,0.0000000000
RAPID
GOTO/27.5935994096,0.0000000000,-102.5000000000
FEDRAT/150.000000,MMPM
GOTO/15.5000000000,0.0000000000,-102.5000000000
GOTO/15.5000000000,0.0000000000,-84.0000000000
CIRCLE/14.0000000000,0.0000000000,-84.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,1.5000000000
GOTO/15.4952229178,0.0000000000,-83.8803821666
GOTO/13.4952229178,0.0000000000,-58.8803821666
CIRCLE/12.0000000000,0.0000000000,-59.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,1.5000000000
GOTO/13.4733969043,0.0000000000,-58.7187500000
CIRCLE/90.5811682275,0.0000000000,-44.0000000000,$
0.0000000000,1.0000000000,0.0000000000,78.5000000000
GOTO/13.4733969043,0.0000000000,-29.2812500000
CIRCLE/12.0000000000,0.0000000000,-29.0000000000,$
0.0000000000,-1.0000000000,0.0000000000,1.5000000000
GOTO/13.5000000000,0.0000000000,-29.0000000000
GOTO/13.5000000000,0.0000000000,-1.1124350607
CIRCLE/12.0000000000,0.0000000000,-1.1124350607,$
0.0000000000,-1.0000000000,0.0000000000,1.5000000000
GOTO/12.8122523462,0.0000000000,0.1486145522
GOTO/11.0851587784,0.0000000000,1.2610496129
$$->END/
$$->FEATNO/527
TURRET/2
$$->CSYS/1.0000000000,0.0000000000,0.0000000000,0.0000000000,$
0.0000000000,1.0000000000,0.0000000000,0.0000000000,$
0.0000000000,0.0000000000,1.0000000000,0.0000000000
SPINDL/RPM,200.000000,CLW
RAPID
GOTO/21.1000000000,0.0000000000,-28.9000000000
FEDRAT/150.000000,MMPM
GOTO/18.1000000000,0.0000000000,-28.9000000000
GOTO/10.1000000000,0.0000000000,-28.9000000000
GOTO/21.1000000000,0.0000000000,-28.9000000000
$$->END/
$$->FEATNO/756
TURRET/1
$$->CSYS/1.0000000000,0.0000000000,0.0000000000,0.0000000000,$
0.0000000000,1.0000000000,0.0000000000,0.0000000000,$
0.0000000000,0.0000000000,1.0000000000,0.0000000000
SPINDL/RPM,200.000000,CLW
RAPID
GOTO/15.0000000000,0.0000000000,0.0000000000
FEDRAT/150.000000,MMPM
OP/THREAD,TURN,DEPTH,1.000000,TPI,2.100000,CUTS,1,FINCUT,1,$
CUTANG,180.000000
GOTO/12.0000000000,0.0000000000,0.0000000000
GOTO/12.0000000000,0.0000000000,-26.0000000000
OP/THREAD,NOMORE
RAPID
GOTO/15.0000000000,0.0000000000,0.0000000000
SPINDL/OFF
$$->END/
FINI
5.3区域车削自动编程生成的NC程序清单
%
G71
O0000
（D:
\我的文档\op010111.ncl.1）
（12/16/10-20:
02:
49）
S200M03
G00X17.6Y0.
Z1.5
G01X15.5F150.
Z-102.586
X16.6
G00Z1.5
G01X14.5
Z-71.44
X15.495Z-83.88
X16.595
G00Z1.5
G01X13.5
Z-58.94
X14.5Z-71.44
X15.6
G00Z1.5
G01X12.699
Z.242
X12.807Z.173
G18
G02X13.5Z-1.092I-.807
G01X14.6
G00Z1.5
G01X11.897
Z.753
X12.699Z.242
X13.799
G00Z1.5
G01X11.096
Z1.265
X11.897Z.753
X12.997
G00X14.6
Z-29.
G01X13.5
X13.473Z-29.281
G03X12.791Z-33.47I77.108
G01Z-54.53
G03X13.473Z-58.719I77.79
G01X13.495Z-58.88
X14.595
G00Z-33.47
G01X12.791
G03X12.081Z-44.I77.79
X12.791Z-54.53I78.5
G01X12.335Z-50.311
G03X13.473Z-58.719I78.246
G01X13.495Z-58.88
X15.495Z-83.88
X15.5Z-84.
Z-102.586
X17.6
G00Z-102.5
X27.594
G01X15.5
Z-84.
G03X15.495Z-83.88I-1.5
G01X13.495Z-58.88
G03X13.473Z-58.719I-1.495
G02X13.473Z-29.281I77.108
G03X13.5Z-29.I-1.473
G01Z-1.112
G03X12.812Z.149I-1.5
G01X11.085Z1.261
S200
G00X21.1
Z-28.9
G01X18.1
X10.1
X21.1
S200
G00Z0.
X15.
G01X12.
Z-26.
G00Z0.
X15.
M30
%
六、轮廓车削
6.1轮廓车削屏幕演示截图
6.2轮廓车削刀位文件
$$*Pro/CLfileVersionWildfire4.0-M140
$$->MFGNO/MFG0001
PARTNO/MFG0001
$$->FEATNO/24
MACHIN/UNCX01,1
$$->CUTCOM_GEOMETRY_TYPE/OUTPUT_ON_CENTER
UNITS/MM
TURRET/1
$$->CSYS/1.0000000000,0.0000000000,0.0000000000,0.0000000000,$
0.0000000000,1.0000000000,0.0000000000,0.0000000000,$
0.0000000000,0.0000000000,1.0000000000,0.0000000000
SPINDL/RPM,200.000000,CLW
RAPID
GOTO/17.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/15.5000000000,0.0000000000,1.5000000000
GOTO/15.5000000000,0.0000000000,-102.5857864376
GOTO/16.6000000000,0.0000000000,-102.5857864376
RAPID
GOTO/16.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/14.5000000000,0.0000000000,1.5000000000
GOTO/14.5000000000,0.0000000000,-71.4400956940
GOTO/15.4952229178,0.0000000000,-83.8803821666
GOTO/16.5952229178,0.0000000000,-83.8803821666
RAPID
GOTO/16.5952229178,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/13.5000000000,0.0000000000,1.5000000000
GOTO/13.5000000000,0.0000000000,-58.9400956940
GOTO/14.5000000000,0.0000000000,-71.4400956940
GOTO/15.6000000000,0.0000000000,-71.4400956940
RAPID
GOTO/15.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/12.6986627382,0.0000000000,1.5000000000
GOTO/12.6986627382,0.0000000000,0.2418660249
GOTO/12.8068605844,0.0000000000,0.1728267622
CIRCLE/12.0000000000,0.0000000000,-1.0916794644,$
0.0000000000,1.0000000000,0.0000000000,1.5000000000
GOTO/13.5000000000,0.0000000000,-1.0916794644
GOTO/14.6000000000,0.0000000000,-1.0916794644
RAPID
GOTO/14.6000000000,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/11.8973254764,0.0000000000,1.5000000000
GOTO/11.8973254764,0.0000000000,0.7531861258
GOTO/12.6986627382,0.0000000000,0.2418660249
GOTO/13.7986627382,0.0000000000,0.2418660249
RAPID
GOTO/13.7986627382,0.0000000000,1.5000000000
FEDRAT/150.000000,MMPM
GOTO/11.0959882146,0.0000000000,1.5000000000
GOTO/11.0959882146,0.0000000000,1.2645062267
GOTO/11.8973254764,0.0000000000,0.7531861258
GOTO/12.9973254764,0.0000000000,0.7531861258
RAPID
GOTO/14.6000000000,0.0000000000,0.7531861258
RAPID
GOTO/14.6000000000,0.0000
升级会员 