QPQ006 模具管理控制程序.docx
《QPQ006 模具管理控制程序.docx》由会员分享,可在线阅读,更多相关《QPQ006 模具管理控制程序.docx(5页珍藏版)》请在冰豆网上搜索。
QPQ006模具管理控制程序
1.目的Purpose
为使本公司之模具从使用、校正、修理及报废阶段作业皆有依据可循,特制订本管理办法。
Thismanagementregulationismadetostandardizetheoperationofusing,adjusting,repairingandscrapmold.
2.范围Scope
全公司所有使用之注塑模具均适用之
ItappliestoallinjectionmoldsofVTYC.
3.定义definition
模具维修:
涉及产品外观、尺寸和模具异常的量产模具修理。
Repairing:
itreferstorepairSOPmoldontheappearance,dimensionandabnormity.
维护保养:
正常情况下模具生产达到一定数量后的例行维护及保养。
Maintenance:
regularmaintenanceafteritreachingcertainshotvolume.
4.职责duty
4.1常州采购单位:
负责依单据发包承制、采购等作业。
PurchasedepartmentinChangzhou:
beresponsibleforoutsourcingandpurchasingmoldinaccordancewiththedocuments.
4.2常州模具单位:
负责模具规划、制作并确认。
ToolingdepartmentinChangzhou:
beresponsibleforplanning,manufacturingandconfirmingofmolds.
4.3重庆模具课:
负责模具的验收与管理,维修与保养等作业。
EngineeringdepartmentinChongqing:
beresponsibleforchecking,managingandmaintainingofmolds
4.4质量单位:
确认该模具生产出产品符合品质要求。
QA:
ensureproductmadebythemoldmeetsthequalityrequirement.
4.5精益生产部:
负责模具的保管和配合模具课保养等作业
VS:
beresponsibleforkeepingandworkingtogetherwithtoolingdepartmenttomaintainmolds.
5.程序procedure
5.1简易流程simpleprocess
验收—管理--维修--保养--报废
Checking&acceptance—management—repairing—maintenance--Scrap
5.2具体描述specificdescription:
5.2.1验收checking&acceptance:
5.2.1.1在重庆生产的模具的验收,需要在重庆连续生产250模以上作为量产验证,记录在产品试模状态统计表FRC(FM-T089)中;
ToacceptamoldinChongqingneedscontinuouslymanufacturingover250productsintheplantformass-productionverification,themoldtrailconditionshouldberecordedinmoldtrailFRCform(FM-T089).
5.2.1.2生产良品率要求到达95%以上。
试模生产情况记录在产品试模状态统计表由精益生产部提供(FRC)(FM-T089)
ThemoldisOKwhentheyieldratehasreached95%.VSoffermoldtry-outstatisticaltable(FM-T089).
5.2.1.3接收模具资料(最新3D数据,模具备件清单)点检模具外观,包括模具信息铭牌,热流道铭牌,水路铭牌,感应开关,接线盒等。
验收完毕以后由模具部填写《模具验收报告》(FM-T088).Toolingdepartmentshouldcompletethe“moldreceivingreport”(FM-T088)forreceivingmoldmaterialssuchasthelatest3Ddata,spareparts,andinspectingmoldappearancesuchasmoldnameplate,hotrunnernameplate,watergatenameplate,sensorswitchandterminalbox.
5.2.1.4模具部根据精益生产部提供的“试模统计表FRC”(FM-T089)以及“模具验收报告(FM-T088)作为验收合格的佐证,记录保存在模具部。
MoldtrailFRCform(FM-T089)andmoldchecking&acceptancereport(FM-T088)offeredbyVSareusedasevidenceofacceptingamoldbytoolingdepartment.Thetoolingdepartmentshouldkeeptheseforms.
5.2.1.5如果模具验收不合格,由模具部负责通知常州模具单位,配合维修工作。
IfamoldNG,thetoolingdepartmentinformsCZtoolingdepartmentofworkingtogethertorepairit.
5.2.2管理:
management
5.2.2.1由模具部对所有在重庆工厂生产的模具建立《模具清单》(FM-T082);并根据每付模具信息建立《模具履历表》(FM-T086)包括模具编号、材质、尺寸等信息。
Thetoolingdepartmentshouldestablishmoldinventory(FM-T082)forallmoldsinCQplant,andmoldinformationsheet(FM-T086)foreveryindividualmold,detailinginmoldnumber,materialanddimension,etc.
5.2.2.2模具的备品建立备品清单及备品库存。
每月对模具备件的清查,保证备件和日常工具的库存。
Establishsparepartslistandsparepartsinventory.Takesparepartsstockmonthlytoensureenoughreserve.
5.2.2.3待模具卸下机器以后,由注塑课负责在模具上挂上由模具部提供的状态标识。
Whenthemoldremovefromthemachine,toolingdeptresponsibleformakethestatussignforeachmold.
模具正常:
模具维修、保养以后挂上(模具正常)的标识牌。
Moldok:
referstothemoldstatusisok,afterrepairorpreventivemaintenance.
模具故障:
在需要维修的模具上,挂上(模具维修)的标识牌。
Moldfailure:
refertothemoldneedtoberepaired.
模具保养:
在待保养的模具上,挂上(模具保养)得标识牌。
Moldpreventivemaintenance:
referstothemoldneedtobedonethepreventivemaintenance.
模具报废:
等待报废及已经报废的模具挂在模具明显部位挂上(模具报废)的标识牌。
Moldscrap:
referstothemoldscraped.
5.2.3模具维修:
当模具出现异常时,由模具使用单位开出《模具修改申请单》(表单编号:
FM-T085),所在部门主管签字确认后,交往模具课。
由模具部判定自行修理或者委外修理。
Repair:
findingabnormality,theusingunitcompletemoldmodificationapplication(FM-T085)andsendittotoolingdepartmentaftertheusingunitsupervisorsignedit.Thetoolingdepartmentevaluatetorepairititselfortooutsourcerepairing.
5.2.3.1自行维修的模具,由注塑课挂好(模具维修)标示,拉到模具部的模具待修区,模修跟产品有关系的必须在模具上留下最后一模产品,并在产品上标示需要修正的位置。
以便下次验证修正问题点的核对。
然后再开出《模具修改申请单》(表单编号:
FM-T085),所在部门的课长或者经理签字确认后,交往模具课。
内容必须和样件问题点一致。
然后由模具部负责提出维修方案和时间计划,并邮件形式通知各单位主要人员,待物流计划员确认后通知模具课开始模修。
维修完成后登记在《模具履历表》(FM-T086)上。
并把已修好的模具换上(模具正常)的标示牌拉到模具已修区。
并以邮件形式填写(试模通知单)给物流计划员和各部门相关人员。
物流计划员安排试模后提前通知各部门相关人员参与试模和确认。
产品修正确认后模修提出者在《模具修改申请单》上确认签名,以便备档。
Formoldcanberepairedbytoolingdepartment,thetoolingdepartmentshoulddraftrepairschemeandregisteritonmoldinformationform(FM-T086).
5.2.3.2需要委外修理的模具,由采购单位和模具单位共同选择供应商维修或外包维修。
注塑课挂好(模具维修)标示,拉到模具部的模具待修区,模修跟产品有关系的必须在模具上留下最后一模产品,并在产品上标示需要修正的位置。
以便下次验证修正问题点的核对。
然后再开出《模具修改申请单》(表单编号:
FM-T085),所在部门的课长或者经理签字确认后,交往模具课。
内容必须和样件问题点一致。
然后由模具部负责提出维修方案和时间计划,并邮件形式通知各单位主要人员,待物流计划员确认后通知模具课开始模修。
维修情况登记在《模具履历表》上(表单编号:
FM-T086-V1).并把已修好的模具换上(模具正常)的标示牌拉到模具已修区。
并以邮件形式填写(试模通知单)给物流计划员和各部门相关人员。
物流计划员安排试模后提前通知各部门相关人员参与试模和确认。
产品修正确认后模修提出者在《模具修改申请单》上确认签名,以便备档。
Formoldneedsoutsourcingrepairing,thepurchasedepartmentandtoolingdepartmentshouldworktogethertofindoutthesupplier.Recordrepairconditiononmoldinformationform(FM-T086-V1).
5.2.3.3模具或者镶件需要协外维修或者加工时,由模具部填写《原物料放行》单,并由模具主管和物流计划员或者物流主管签字后才能放行,如果是节假日要电话通知警卫放行,但星期一要及时补交。
5.2.4保养:
maintenance
5.2.4.1根据《模具保养及检验表》(FM-Q083)的要求,物流部根据QAD系统统计本周该模具使用数量,并且加入下周生产计划的模具使用数量,如果其总数达到保养要求时由物流部提供《模具保养通知单》(FM-T087)通知模具部安排保养。
模具单位收到《模具保养通知单》以后,回复物流单位保养所需时间,物流单位根据保养安排调整下周生产计划。
MP&LsummarizehowmanymoldshavebeenusedeveryweekperQADdataandaddhowmanyareneedednextweektoitasmoldmaintenance&checkingform(FM-Q083)requires.Iftheresultreachesmaintainingrequirement,MP&Lcompletemoldmaintainingnotification(FM-T087)toinformtoolingdepartmentofmaintenance.Receivingthenotification,toolingdepartmentgivesfeedbacktoMP&Lonwhentomaintainmold.MP&Lrearrangenextweekmanufactureplan.
5.2.4.2模具部负责在待保养的模具,挂上(模具保养)标识牌。
Toolingdepartmentshouldputupmaintainingtagonmoldneedingmaintenance.
5.2.4.3模具保养频次严格按照《模具保养及检验表》(FM-Q083)要求执行,在保养完成后在《模具保养及检验表》(FM-Q083)和《模具履历表》(表单编号:
FM-T086)及《模具清单表》(表单编号:
FM-T082)上登记。
Abidebymoldmaintaining&checkingform(FM-Q083)onthefrequencyofmaintainingamold.Registerinmoldmaintaining&checkingform(FM-Q083),moldinformationform(FM-T086)andmoldinventory(FM-T082)afterfinishingmaintenance.
5.2.4.4模具保养完成后,由模具单位挂上“模具正常”的标识牌。
并把模具拉到模具已修区,并以邮件形式告知各部门相关人员。
Afterfinishingmaintenance,thetoolingdepartmentshouldlabelnormaltag.
5.2.4.5在每次保养时,模具工程师查阅《模具履历表》(FM-T086)中的记录,根据该模具发生过的历史故障原因和使用情况,由模具工程师判定,是否需要对该模具进行针对性保养,并记录在《模具保养及检验表》(FM-Q083)中.Whendoingthepreventivemaintenance,thetoolingengineerresponsibleforcheckmoldinformationform(FM-T086),andanalyzetheusingofmoldtofindthemainfaultcause.Themoldengineershouldassessifitisnecessarytomaketargetedmaintenanceforit.Recordrelatedinformationinmoldmaintaining&checkingform(FM-Q083).
5.2.5报废方法:
使用单位于每年9/1-9/30间提出拟报废模具之明细于模具单位,并召集相关部门判定是否可继续修理。
营业单位根据明细与车模协商是否报废或回收,若车模同意报废,报公司最高主管核准后交财务按照《固定资产报废管理办法》执行;若不同意报废,由营业单位告知各单位原由。
Scrap:
usingunitshouldlistdetailedscrapmoldtabletotoolingdepartmentfromSep.1to30andgatherrelateddepartmentstodecidewhetheritcanberepairedornot.Thesalesdepartmentcommunicateswithcustomerengineertodecidewhethertoscraporrecyclethemold.Ifcustomerengineeragreestoscrap,reportittoVTYChighestmanagementforapproval.Gettingtheapproval,financedepartmentscrapitasfixedassetsscrapmanagementregulationrequires.Ifcustomerengineerrefusestoscrap,salesdepartmentinformsrelatedunitofreason.
6.使用表单forms
6.1重庆模具供应商评审表(FM-T081).
Chongqingmoldsupplierreviewsheet(FM-T081)
6.2模具清单(FM-T082).
Moldinventory(FM-T082)
6.3模具保养及检查表(FM-T083).
Moldmaintenance&checkingsheet(FM-T083)
6.4模具备品清单(FM-T084).
Moldsparepartsinventory(FM-T084)
6.5模具修改申请单(FM-T085).
Moldmodificationapplication(FM-T085)
6.6模具履历表(FM-T086).
Moldinformationsheet(FM-T086)
6.7模具保养通知单(FM-T087)
Preventivemaintenancenoticesheet(FM-T087)
6.8《模具验收报告》(FM-T088)
moldreceivingreport(FM-T088)
6.9《试模状态统计表FRC》(FM-T089)
MoldtrailconditionrecordFRC(FM-T089)
6.10《试模申请单》(FM-T090)