山西7330FTTN操作手册1217.docx
《山西7330FTTN操作手册1217.docx》由会员分享,可在线阅读,更多相关《山西7330FTTN操作手册1217.docx(66页珍藏版)》请在冰豆网上搜索。
山西7330FTTN操作手册1217
7330FTTN宽带及语音配置
(本文档中需要输入的命令均用蓝色字体,其他删除,显示等参考
命令起提示作用,不是流程中必要执行的命令,均用黑色字体)
一.7330FTTN简介:
7330插槽介绍:
物理Slot11分离器板:
NPSP-A可插NPOT,lt:
1/1/8
Cluster4
FAN
物理Slot10宽带数据板:
NALT-B可插NPOT,lt:
1/1/7
物理Slot9分离器板:
NPSP-A可插NPOT,lt:
1/1/6
Cluster3
物理Slot8宽带数据板:
NALT-B可插NPOT,lt:
1/1/5
物理Slot7分离器板:
NPSP-A可插NPOT,lt:
1/1/4
Cluster2
物理Slot6宽带数据板:
NALT-B可插NPOT,lt:
1/1/3
物理Slot5语音用户板:
NPOT-A可插NPOT,lt:
1/1/2
Cluster1
物理Slot4语音控制板:
NVPS-A可插NPOT,lt:
1/1/1
物理Slot3可插NPOT,lt:
1/1/10
不能插NVPS
物理Slot2可插NPOT,lt:
1/1/9
不能插NVPS
物理Slot1主控板:
NANT-A
电源板:
EMA-GFC
7330机框物理slot2,slot3不能插语音控制板NVPS,只能插语音用户板NPOT及宽带用户板NALT.
二.7330数据资源需求信息:
红色框内的数据为7330内部数据,无需向用户申请,只要数据不与其他分配的数据冲突即可,内部IP地址最好用私网的IP地址.NANT-A的PORT-1做上联端口.
管理数据
语音数据
管理IP
58.217.12.194/27
语音IP
10.16.247.34
掩码
255.255.255.224
掩码
255.255.255.224
网关
58.217.12.222
网关
10.16.247.62
管理VLAN
63
语音VLAN
3800
内部IP数据
宽带数据VLAN范围
内部IP
192.168.1.3
1/1/6/1..48
200-247
掩码
255.255.255.0
网关
192.168.1.1
MGC1
10.14.132.37:
2944
内部VLAN
30
MGC2
10.14.132.5:
2944
三.系统登录(9600bps,N,8,1):
WouldyoulikeaCLI(C)oraTL1login(T)orTL1normalsession(N)?
[N]:
c/进入命令行模式
login:
isadmin
password:
i$@mad-/i$@mad-为初始密码,第一次登陆系统会让更改新的密码
WelcometoISAM
Yourpasswordisexpired!
enternewpassword:
ans#150/建议7330全部统一改成该密码
re-enterpassword:
ans#150
Thenewpasswordisaccepted.
注:
现场的7330上如果有数据,且需要要清空数据库可执行以下命令.
adminsoftware-mngtoswp1activateclear-db/执行此命令后重启系统,可清空数据库,重新配置7330.
四.配置7330板卡:
扩槽位
configureequipmentshelf1/1extended-lt-slots
配置板卡
configureequipmentslot1/1/9planned-typenant-aunlock
configureequipmentslot1/1/1planned-typenvps-aunlock
configureequipmentslot1/1/3planned-typenpot-aunlock
configureequipmentslot1/1/4planned-typenpot-aunlock
configureequipmentslot1/1/5planned-typenpot-aunlock
configureequipmentslot1/1/6planned-typenpot-aunlock
configureequipmentslot1/1/7planned-typenpot-aunlock
configureequipmentslot1/1/8planned-typenpot-aunlock
configureequipmentslot1/1/12planned-typenpot-aunlock
configureequipmentslot1/1/13planned-typenpot-aunlock
configureequipmentslot1/1/14planned-typenpot-aunlock
configureequipmentslot1/1/15planned-typenpot-aunlock
configureequipmentslot1/1/16planned-typenpot-aunlock
configureequipmentslot1/1/17planned-typenpot-aunlock
configureequipmentslot1/1/18planned-typenpot-aunlock
configureequipmentslot1/1/19planned-typenpot-aunlock
showequipmentslot/显示板卡配置情况
五.管理数据配置:
5.1配置NT管理地址、LANX管理地址、网关:
configuresystemmanagementhost-ip-addressmanual:
172.31.36.50/24
configuresystemmanagementdefault-route172.31.36.1
configuresystemmanagementnodefault-route/删除网关,即可更改上面的管理IP
5.2打开port1作为上行端口:
PORT0做为上传CDE文件口
configureinterfaceshubport1port-typenetworkadmin-statusauto-up
configureinterfaceshubport0port-typeuseradmin-statusauto-up
configureinterfaceshubport0noport-type/删除上联口
showinterfaceshubport/显示上联口状态
5.3配置管理VLAN:
configuresystemmgnt-vlan-id30
configuresystemshubentryvlanext-vlan-id30
configurevlanshubid30egress-portnetwork:
1
configurebridgeshubport1pvid30
configurevlanshubid30egress-portnetwork:
0
configurevlanshubid30untag-portnetwork:
0
configurebridgeshubport0pvid30
infoconfigurevlanshub/显示vlan
5.4配置NVPS的MEGACOVLAN/VOICEVLAN:
为了避免上层网络设备的ARPPROXY问题导致7330内部语音不通的故障,请将语音vlan做成voice-vlan.
configurevlanshubid3800modevoice-vlan
configurevlanshubid3800egress-portlt:
1/1/1
configurevlanshubid3800egress-portlt:
1/1/3
configurevlanshubid3800egress-portlt:
1/1/4
configurevlanshubid3800egress-portlt:
1/1/5
configurevlanshubid3800egress-portlt:
1/1/6
configurevlanshubid3800egress-portlt:
1/1/7
configurevlanshubid3800egress-portlt:
1/1/8
configurevlanshubid3800egress-portlt:
1/1/12
configurevlanshubid3800egress-portlt:
1/1/13
configurevlanshubid3800egress-portlt:
1/1/14
configurevlanshubid3800egress-portlt:
1/1/15
configurevlanshubid3800egress-portlt:
1/1/16
configurevlanshubid3800egress-portlt:
1/1/17
configurevlanshubid3800egress-portlt:
1/1/18
configurevlanshubid3800egress-portlt:
1/1/19
configurevlanshubid3800egress-portnetwork:
1
configurevlanshub noid3800/删除vlan命令
configurevlanshubid3800noegress-portlt:
1/1/5/删除lt:
1/1/5上的vlan3800
configurevlanshubid3800noegress-portnetwork:
1/删除network1上的vlan3800
5.5配置PRIVATEVLAN(VLAN30为7330内部VLAN,只要不与数据VLAN冲突即可):
configurevlanshubid200modevoice-vlan
configurevlanshubid200egress-portlt:
1/1/1
configurevlanshubid200egress-portlt:
1/1/3
configurevlanshubid200egress-portlt:
1/1/4
configurevlanshubid200egress-portlt:
1/1/5
configurevlanshubid200egress-portlt:
1/1/6
configurevlanshubid200egress-portlt:
1/1/7
configurevlanshubid200egress-portlt:
1/1/8
configurevlanshubid200egress-portlt:
1/1/12
configurevlanshubid200egress-portlt:
1/1/13
configurevlanshubid200egress-portlt:
1/1/14
configurevlanshubid200egress-portlt:
1/1/15
configurevlanshubid200egress-portlt:
1/1/16
configurevlanshubid200egress-portlt:
1/1/17
configurevlanshubid200egress-portlt:
1/1/18
configurevlanshubid200egress-portlt:
1/1/19
configureipshubvrf2fast-path-mode:
ena-user-user-comnamevoice
configureinterfaceshubvlan-id3800admin-statusdown
configureinterfaceshubip3800vrf-id2
configureinterfaceshubvlan-id3800admin-statusup
configureinterfaceshubvlan-id200admin-statusdown
configureinterfaceshubip200vrf-id2
configureinterfaceshubip200ip-addr192.168.1.3/24
configureipshubvrf2route-dest0.0.0.0/0next-hop192.168.1.1vlan-id200
configureinterfaceshubvlan-id200admin-statusup
5.6关闭NT板冗余配置:
configureequipmentprotection-group1admin-statuslock
此命令根据现场配置,双NT可省略此条命令,但现场如果采用NT单配,需要关掉NT冗余保护.
5.7关闭MSTP功能:
configuremstpgeneraldisable-stp/单上联时涉及不到此处设置,需关闭MSTP
5.8设置系统时间:
adminsntpsystem-time2011-11-18:
10:
21:
00
5.9保存SHUB配置:
adminsoftware-mngtshubdatabasesave
5.10配置完成后用查看上述相关配置:
showinterfaceshubport/端口及NTIO接口卡上的端口情况
infoconfigurevlanshub/查看VLAN配置情况,检查无误开始配置VOIP部分
5.10配置SNMP
configuresystemsecuritysnmpcommunitypublichost-address0.0.0.0/0privilegeread-write
configuresystemsecuritysnmpcommunityNETMANhost-address0.0.0.0/0contextshub
configuresystemsecuritysnmpcommunityxvps1host-address0.0.0.0/0contextxvps1
六.语音部分配置:
6.1下载CDE文件:
6.1.1设置CDE文件TFTP服务器:
PC直连网线连接NANT-A的PORT-0,注意要关闭PC的防火墙.进行port0口的设置,使其可以与PC通信.
登陆NT,在CLI命令下输入:
前面已配
configureinterfaceshubport0port-typeuser
configureinterfaceshubport0admin-statusauto-up
configurevlanshubid63untag-portnetwork:
0
configurebridgeshubport0pvid63
以3CDaemonTFTP服务器软件为例,在PC上安装好软件后,点击ConfigureTFTPServer后,在弹出的窗口中配置upload/downloaddirectory栏,即CDE文件所保存的目录.比如下图的目录D:
\tftp\,此时CDE文件应存放在该目录下.
6.1.2下载CDE文件:
isadmin>adminsoftware-mngtcdeprofdownload172.31.36.51:
MSR2AE33.116
注:
1.58.217.12.196为TFTP服务器PC的地址,该地址要和7330管理地址在同一网段.
2.MSR2AE33.111为CDE的文件名.该文件中存有中国PSTN语音业务的一些重要参数,如拨号音频率,RTP格式,软交换注册域名(如果用域名注册的话)等.如果有些参数需要更改,则需要公司重新生成一个CDE文件发到现场,传到NT板上.
6.1.3查看NT板中CDE文件状态:
可以通过下面命令来查看CDE下载情况,比如下图为下载成功时候的截图,刚下载CDE后的状态为New.
isadmin>showsoftware-mngtcdeprofdldstatus
================================================================================
dldstatustable
================================================================================
server-ip:
10.78.10.110
path:
MSR2AE33.111(New)
download-progress:
download-success
download-error:
no-error
================================================================================
6.1.4激活CDE文件:
isadmin>adminsoftware-mngtcdeprofactivateMSR2AE33.112
激活后再查看CDE状态:
isadmin>showsoftware-mngtcdeprofdldstatus
================================================================================
dldstatustable
================================================================================
server-ip:
10.78.10.110
path:
MSR2AE33.111(Activated)
download-progress:
download-success
download-error:
no-error
================================================================================
状态已变为Activated,说明此CDE已经生效.
6.2配置XLES:
configurevoicecluster1ipivps-ip10.43.0.80netmask255.255.255.0router-ip10.43.0.1vlan-id3800private-ip192.168.1.2private-netmask255.255.255.0private-vlan-id200
cluster计算:
1.由于语音控制板NVPS也是一种控制板,只不过其只能控制和识别语音板NPOT,而不能识别NT板,因此语音板NPOT和7330物理槽位编号不同.
2.语音控制板只能插在7330机框从下往上的物理槽位的4~11槽位.另外一台7330一般只插一块NVPS,因此该NVPS所在槽位决定了cluster编号.一台7330一个cluster编号,实际上是语音控制板和语音板之间的逻辑通道号.系统通过cluster编号,将语音用户板的信息写入语音控制板.
3.若NVPS在物理上第一二槽就是cluster1,第三四槽位就是cluster2,第五六槽位就是cluster3,第七八槽位就是cluster4.
Infoconfigurevoicecluster1media-gateway1/查看MG配置
showvoicecluster1media-gateway1/查看MG状态
打死激活网管
configurevoicecluster1media-gateway1admin-statuslock
6.3配置MGC:
configurevoicecluster1media-gateway1namefllip-address10.43.0.80netmask255.255.255.0vlan-id3800prim-mgc-ip10.5.33.3router-ip10.43.0.1
6.4设置物理终结点格式:
configurevoicecluster1media-gateway1mgc-typehw-soft3000termid-typeflatpstn-term-formatAisdn-term-formatA
注:
1.该命令配置物理终结点格式,必须整条一次性输入,尤其pstn,isdn两部分要一起输入,否则报错.
2.ONU110A/rack/shelf/slot/port物理端口前缀,形如:
ONU110A/1/1/2/1
6.5设置7330与MGC之间的心跳:
configurevoicecluster1media-gateway1active-heartbeatfix:
30000passive-heartbeatdynamic/30000ms为心跳间隔,调整该值可以调整心跳消息发送频率
6.6完成上述配置后用如下命令检查:
configurevoicecluster1media-gateway1admin-statusunlocked/激活网关
showvoicecluster1media-gateway1/查看网关是否注册到软交换上
infoconfigurevoicecluster1media-gateway1/显示网