自攻螺丝自攻螺丝扭力强度.docx
《自攻螺丝自攻螺丝扭力强度.docx》由会员分享,可在线阅读,更多相关《自攻螺丝自攻螺丝扭力强度.docx(11页珍藏版)》请在冰豆网上搜索。
自攻螺丝自攻螺丝扭力强度
自攻螺丝自攻螺丝-扭力强度
(4)TorqueStrength
TorqueWrench(0~150kgf)(150~750kgf)購買(150~300kgf)
ASMEB18.6.3/FIP1000/SAEJ78,J81,J1237,J933/ISO898-7,ISO2702/DIN7500-1/IFI-113
2.TORSIONALSTRENGTHTEST扭力強度試驗
FIP1000
ApplicableTo:
AllTappingScrews.
適用範圍:
所有種類的自攻螺絲
TestPurpose:
Todetectpartshavinglowstrengthwhichmighttwistoffduringdrivingorseating.
測試目的:
為檢查零件是否因為扭力不足而在組裝或旋緊時扭斷.
Specification:
Seechartsthatfollow.如下圖示
Apparatusrequired:
測試裝置
A.AppropriateSplitCollet.適當的夾具
B.ColletHolder.夾具座
C.ScrewTestingFixture.螺絲測試座
D.TorqueWrench;accuratewith+/-2%.準確度在±2%以內的扭力扳手
SampleSize(MinimumRecommended):
4piecesperlot;lotsizenottoexceed250,000
抽樣數(建議最少):
每批4支,每批批量不超過250MPCS.
Procedure:
測試程序
A.Placethesplitcolletintothecolletholderandscrewthefastenerintothecolletsuchthataminimumof2fullthreadsareinthecolletandaminimumof2threadsareabovethecollet.
將螺絲置入測試夾具中再將夾具放入夾具座,螺絲至少應有兩個完全牙在夾具中,兩牙在夾具上方.
B.Placethecolletholderinthescrewtestingfixtureandclampintoplace.
將夾具座固定在螺絲測試座上
C.Applytorquewithatorquewrenchuntiltheparttwistsoff.
扭轉扳手直到螺絲扭斷
D.Recordfailurevalueandcomparetotherequiredspecification.
記錄破壞值且與規範值比較
Failure:
Parttwistsintwoatlessthanspecifiedminimum.
失效:
螺絲扭斷值小於規範值
PossibleFailureCauses:
失效可能因素
A.CoreHardnesstoolow.心部硬度太低
B.CaseHardnesstoolow.表面硬度太低
C.CaseHardnesstooshallow.有效滲碳層不足
D.Minordiametertoosmall.最小徑(牙底徑)太小
–2013
TorsionalStrengthTest.Screwsshallbesecurelyclampedbysuitablemeans,suchthattheclampedportionthreadsarenotdamagedandthatatleasttwofullthreadsprojectabovetheclampingdevice,andthatatleasttwofullthreadsexclusiveofpoint,flutes,orendslot,areheldwithintheclampingdevice.(Ablindholemaybeusedinplaceofathreadedclampingdevice,providedtheholedepthsissuchastoinsurethatbreakagewilloccurbeyondthepointorthefulllengthoftheflutesorendslot).Bymeansofasuitablycalibratedtorquemeasuringdevice,torqueshallbeappliedtothescrewuntilfailureoccurs.ThetorquerequiredtocausefailureshallnolessthantheminimumvaluegiveninTable50forthetypeandsizeofscrewbeingtested.AtypicalfixtureforconductingtorsionalstrengthtestsontappingscrewsisdepictedinFig.4.
扭力強度測試:
螺絲應以適當的方式安全的夾於一相配合的分離盲孔或其他裝置中以防止所夾緊的螺紋不致損毀,並且露出至少2全牙於夾具上至少2全牙(不包括尾端、割尾、或凹槽)握於夾具之中。
(盲孔可以取代螺紋夾具,其孔深應能保証螺絲不會在尾端、割尾全長或尖尾位置斷裂)以一校正過且適當的扭力量測設備,測試直到斷裂為止,當斷裂時的扭力應不可小於表50之最小值。
典型的扭力強度測試設備請參考圖4。
圖4-扭力強度測試參考圖
表50-自攻螺絲之扭力強度要求
螺絲規格
最小扭力強度,lb-in.
TypeA
Type
AB,B,BF,BP,BT
TypeC,D,F,G,T
TypeTRS
粗牙
細牙
粗牙
細牙
#2
4
4
5
6
6
…
#3
9
9
9
10
10
…
#4
12
13
13
15
14
…
#5
18
18
18
20
22
…
#6
24
24
23
27
24
…
#7
30
30
……
……
…
…
#8
39
39
42
47
48
…
#10
48
56
56
74
65
74
#12
83
88
93
108
93
…
#14
125
…
…
…
…
…
1/4
…
142
140
179
156
…
#16
152
…
…
…
…
…
#18
196
…
…
…
…
…
5/16
…
290
306
370
330
…
#20
250
…
…
…
…
…
#24
492
…
…
…
…
…
3/8
…
590
560
710
600
…
7/16
…
620
700
820
840
…
1/2
…
1020
1075
1285
…
1080
–2000
3.3TorsionalStrengthTestforAllTypesofScrews.Theshankofthesamplescrew(coatedoruncoated,asreceived)shallbesecurelyclampedinamating,split,blindholedie(seeFig.1),orotherequivalentmeans,suchthatthefollowingrequirementsaremet:
所有類型之螺絲的扭力強度測試:
將螺絲(接收時有塗層或無塗層)的桿部安全的夾在一個相配合的分離盲孔模具(參閱圖1),或其他相同裝置中,並滿足下列規定:
(a)theclampedportionofthethreadsisnotdamaged
被夾部位的螺紋不能損傷
(b)atleasttwofull-formthreadsprojectabovetheclampingdevice
至少2全牙突出於夾具上方
(c)atleasttwofull-formthreadsexclusiveofthepointtaperortheflutesareheldwithintheclampingdevice(ablindholemaybeusedinplaceoftheclampingdevice,providedtheholedepthensuresthatscrewbreakagewilloccurbeyondthepointtaperorthefulllengthoftheflutes)
至少2全牙(不包括尾端、割尾、或凹槽)夾在夾具之中。
(盲孔可以取代夾緊裝置,其孔深應能保證螺絲不會在尾端、割尾全長或尖尾位置斷裂)
Bymeansofasuitablycalibratedtorque-measuringdevice,torqueshallbeappliedtothescrewuntilfailureoccurs.ThetorquerequiredtocausefailureshallequalorexceedtheminimumvaluespecifiedinTable4forthetypeandsizeofscrewbeingtested.
以一校正過之適當的扭力量測設備,測試螺絲直到產生斷裂。
當斷裂時的扭力應不可小於表4規定之最小值。
FIG.1TYPICALTORSIONALSTRENGTHTESTFIXTURE
表4-自攻螺絲之扭力強度要求
TypeAB,B,BF,BT螺絲
TypeD,F,T螺絲
螺絲規格
扭力,Nm
螺絲規格
扭力,Nm
16
M6x1
16
33
40
67
78
SAEJ78-2013SteelSelf-DrillingTappingScrews鋼鐵自鑽螺絲
(IFI113與SAEJ78完全相同)
5.1TorsionalStrength—ScrewsshallnotfailwiththeapplicationofatorquelessthanthetorsionalstrengthtorquespecifiedinTable5,whentestedinaccordancewith.
扭力強度:
當依據段所述測試時,螺絲扭斷時的扭力強度應不能小於表5所列的數值。
TORSIONALSTRENGTHTEST—Thesamplescrewshallbesecurelyclampedbysuitablemeans(Figure5)suchthatthethreadsintheclampedlengtharenotdamaged,andthatatleasttwofullthreadsprojectabovetheclampingdevice,andthatatleasttwofullthreadsexclusiveofpoint,flutes,orthreadcuttingslot,areheldwithintheclampingdevice.Bymeansofasuitablycalibratedtorquemeasuringdevice,torqueshallbeappliedtothescrewuntilfailureofthescrewoccurs.Thetorquerequiredtocausefailureshallberecordedasthetorsionalstrengthtorque.
扭力強度測試:
螺絲樣品應安全的被夾緊於適當的夾座(圖5)以防止螺絲夾緊長度部位的螺紋損傷,並且露出至少2個全牙於夾具上,至少2個全牙握於夾具之中但不包括尾端、凹槽、或割溝螺紋在內。
以一校正過適合的扭力設備測試直到斷裂,斷裂時所記錄的扭力就是扭力強度扭力。
表5-TypeBSD與TypeCSD自鑽螺絲的機械性與功能性要求
公稱螺絲尺寸
最小扭力強度,lb-in
TypeBSD(寬牙)
TypeCSD(機械牙)
#4
14
14
#6
24
24
#8
42
48
#10
61
65
#12
92
100
1/4
150
156
SAEJ81-2012ThreadRollingScrews螺紋滾牙螺絲
TORSIONALSTRENGTH—ScrewsshallnotfailwiththeapplicationofatorquelessthanthetorsionalstrengthtorquespecifiedinTables5Aand5B,whentestedinaccordancewith4.5.
扭力強度:
依據段所述測試時,螺絲扭斷時的扭力強度不能小於表5所列的數值。
4.5TorsionalStrengthTest—Thesamplescrewshallbesecurelyclampedbysuitablemeans(Figure2)suchthatthethreadsintheclampedlengtharenotdamaged,andthatatleasttwofullthreadsprojectabovetheclampingdevice,andthatatleasttwofullthreadsexclusiveofpoint(2to31/2threadpitches)areheldwithintheclampingdevice.Ablindholemaybeusedinplaceofathreadedclampingdevice,providedtheholedepthsissuchastoinsurethatbreakagewilloccurbeyondthepoint(2to31/2threadpitches).Bymeansofasuitablycalibratedtorque-measuringdevice,torqueshallbeappliedtothescrewuntilfailureofthescrewoccurs.Thetorquerequiredtocausefailureshallberecordedasthetorsionalstrengthtorque.
扭斷強度測試:
螺絲樣品應以適當的方式牢固的夾緊(圖2)以防止在夾具中的螺紋不被損傷,並且露出至少2個完全牙在夾具上,以及至少2個完全牙(不包括2-3.5P的尾端在內)握於夾具之中。
一種盲孔可以使用來取代螺紋夾具,所提供之孔深需能確保斷裂不會產生在尾端(2-3.5P)處。
以一支校正過的適當扭力設備測試直到斷裂。
失效的扭力應被記錄並作為扭斷強度扭力。
4.10TorqueWrenches—Torquewrenchesusedinalltestsshallbeaccuratewithin±2%ofthemaximumofthespecifiedtorquerangeofthewrench.Alternatively,atorque-sensingpowerdeviceofequivalentaccuracymaybeused.
扭力扳手:
測試時使用的所有扭力扳手,其準確度應在扳手最大扭力範圍的±2%之內。
此外擁有相同準確度的扭力感應動力裝置也可被使用。
表5-螺紋滾牙螺絲的機械性能與功能性要求
螺絲規格
最小扭力強度
in-lb
2-56
6
3-48
10
4-40
14
5-40
22
6-32
24
8-32
48
10-24
65
1/4-20
156
5/16-18
330
3/8-16
600
7/16-14
840
1/2-13
1080
SAEJ933-2013MechanicalandQualityRequirementsforTappingScrews自攻螺絲的機械性與品質要求
3.3TorsionalStrengthTest—Shankofsamplescrew(coatedoruncoated,asreceived)shallbesecurelyclampedinamating,split,blind-holedie(Figure1)orothermeans,suchthattheclampedportionofthethreadsisnotdamagedandatleasttwofullthreadsprojectabovetheclampingdeviceandatleasttwofullformthreadsexclusiveofpoint,flute(s),orendslotareheldwithintheclampingdevice.(Ablindholemaybeusedinplaceoftheclampingdevice,providingtheholedepthissuchastoinsurethatthebreakagewilloccurbeyondthepoint,orthefulllengthoftheflute(s)orendslot.)Bymeansofasuitablycalibratedtorquemeasuringdevice,applytorquetothescrewuntilfailureoccurs.ThetorquerequiredtocausefailureshallequalorexceedtheminimumvalueshowninTable2forthetypeandsizeofscrewbeingtested.
扭力強度測試:
螺絲樣品的桿部(接收時是電鍍或未電鍍)應被穩固的夾於一相配合的分開盲孔中(圖1)或用其他方式,使被夾緊的螺紋部分不受到損傷,並且露出至少2個全牙於夾具上及至少2個全牙(不包括尾端、割尾或末端)握於夾具之中。
(一種盲孔可以用來取代夾具,其孔深應能保證螺絲不會在尾端、割尾全長、或尖尾位置斷裂)。
以一支校正過且適當的扭力量測設備,施加扭力於螺絲上直到斷裂為止,斷裂時的扭力應等於或大於表2所列的最小值。
表2-自攻螺絲的最小扭力強度要求
螺絲規格
最小扭力強度,lb-in
TypeA
TypeAB,B,BF,BG,BP和BT
TypeC
TypeC,D,F,G,T
粗牙
細牙
粗牙
細牙
No.2
4
4
5
6
5
6
No.3
9
9
9
10
9
10
No.4
12
13
13
15
13
15
No.5
18
18
18
20
18
20
No.6
24
24
23
27
23
27
No.7
30
30
-
-
-
-
No.8
39
39
42
47
42
47
No.10
48
56
56
74
56
74
No.12
83
88
93
108
93
108
No.14
125
-
-
-
-
-
1/4
-
142
140
179
140
179
No.16
152
-
-
-
-
-
No.18
196
-
-
-
-
-
5/16
-
290
306
370
306
370
No.20
250
-
-
-
-
-
No.24
492
-
-
-
-
-
3/8
-
590
560
710
560
710
7/16
-
-
-
-
-
-
1/2
-
-
-
-
-
-
SAEJ1237-2001MetricThreadRollingScrews公制螺紋滾牙螺絲
TORSIONALSTRENGTH—Type2•screwsshallnotfailwiththeapplicationofatorquelessthanthetorsionalstrengthtorquespecifiedinTable6whentestedinaccordancewith4.5.
扭力強度:
當依據段測試時,Type2•螺絲扭斷時的扭力強度應不能小於表6所列的數值。
表6-Type2•螺紋滾成螺絲的機械性要求
螺絲規格
最小扭力強度
4.5TorsionalStrengthTest—Thesamplescrewshallbesecurelyclampedbysuitablemeans(Figure3)suchthatthethreadsintheclampedlengtharenotdamaged,andthatatleasttwofullthreadsprojectabovetheclampingdevice,andthatatl