斯沃数控仿真及破解说明.docx
《斯沃数控仿真及破解说明.docx》由会员分享，可在线阅读，更多相关《斯沃数控仿真及破解说明.docx（38页珍藏版）》请在冰豆网上搜索。
斯沃数控仿真及破解说明
斯沃数控仿真考试提交说明：
1毛坯选着；100xФ45
螺纹的局部放大图（下图蓝色长方形区域；线表示螺纹）
以下是：
控制面板局部放大图及其参数的设置值（根据毛坯和对刀时的切削量来定，）
2．对刀：
有三把刀：
1。
外圆车刀（刀片角度为55°）2。
割刀（宽度改为4mm）3。
螺纹刀对三次。
注意切割量尽量小：
用脉冲形式Z﹣。
3．程序如下：
O4599%（一定要起个名字）
N10T0101;
N20G00X100Z100;
N30M03S800;
N40G00X46Z2;;%毛坯为45mm，故离开毛坯（46-45）/2mm，
N50G71U1.5R0.5;
N60G71P70Q190U0.6;
N70G01X0F80;
N80Z0;
N90X8;
N100G03X18Z-5R5;
N110G01Z-10;
N120X20.85;%（x从18到20..85）
N130X23.85Z-12;%第一次倒角注意x不是24mm
N140Z-32;
N150X26;
N160X36W-14;
N170W-7;
N180G02X42W-3R3;
N190G01Z-66;
N200G70P70Q190M03S1200;
N210G00X100Z100;
N220T0202;
N230M03S500;
N240G00X28Z-32;
N250G01X20;切草了
N260G00X28;%快速点定位
N270W1;
N280G01X20;
N290W-1;
N300G00X28;%快速点定位
N310X100Z100;
N320T0303;
N330M03S400;
N340G00X25Z-9;
N350G92X23.2Z-29;F1.5;
N360X22.6;
N370X22.2;
N380X22.04;
N390G00X100Z100;
N400T0202;%目的是近似于切断。
。
。
。
N410G00X43Z-69;
N420G01X3F30;
N430G00X45;
N440X100Z100;
N450M30
斯沃数控-车床编程与走刀-
（2）huaxia学院机电工程----四把刀
1。
外圆车刀（刀片角度为55°）2。
割刀（宽度改为4mm）3.螺纹刀（唯一）。
4左偏尖刀55°。
（或叫右偏）
O0633
N10T0101;
N20G00X100Z100;
N30M03S650;
N40G00X46Z2;%毛坯附近相差2mm
N50G71U1.5R0.5;%粗加工，u每次切1.5mm，退刀量0.5
N60G71P70Q160U0.5w0.1F100;
N70G00X0;
N80G01Z0F80;
N90X26;%30-4D;
N100X30Z-2;
N110Z-27;
N120X32;
N130X36Z-35;
N140x-41;
N150X40Z-65;
N160Z-76;%WHY?
N170G70P70Q160M3S800;%精加工
N180G0X100Z100;
N190T0404M3S600;
N200G0X38Z-41;
N210G73U3;%单边余粮3mm
N220G73PQU0.3W0F60;
N230G01X36Z-41;
N240G02U-6W-9R15;
N250U10W15R25;
N260G70P230Q250M3S800;%
N270T0202M3S450;
N280G0X34Z-27;
N290G01X26F30;
N300G0X34;
N310W3;
N320X26
N330W-3;
N340GOX34;
N350X32Z-21;
N360G1X26Z-24;
N370G0X34;
N380X100Z100;
N390T0303;
N400G0X32Z3;
N410G92X29.2Z-22F1.5;
N420X28.6;
N430X28.2;
N440X28.04
N450G00X100Z100;
N460T0202;
N470G00X42Z-74;
N480G01X3F30;
N490G00X45;
N500X100Z100;
N510M30
或者用简洁的无注视的程序：
o1008
N10T0101
N20G00X100Z100
N30M03S650
N40G00X46Z2
N50G71U1.5R0.5
N60G71P70Q160U0.5W0.1F100
N70G1X0F80
N80Z0
N90X26
N100X30Z-2
N110Z-27
N120X32
N130X36Z-35
N140Z-41
N150X40Z-65
N160Z-76
N170G70P70Q160M3S800
N180G00X100Z100
N190T0404M03S600
N200G00X100Z100
N210G73U3R5
N220G73P230Q250U0.3W0F60
N230G01X36Z-41
N240G02U-2W-9R15
N250U10W-15R25
N260G70P230Q250M03S800
N270G00X100Z100
N280T0202M3S450
N290G00X34Z-27
N300G01X26F30
N310G00X34
N320W3
N330G01X26
N340W-3
N350G00X34
N360X32Z-21
N370G01X26Z-24
N380G00X34
N390X100Z100
N400T0303
N410G00X32Z-3
N420G92X29.2Z-22F1.5
N430X28.6
N440X28.2
N450X28.04
N460G00X100Z100
N470T0202
N480G00X42Z-74
N490G01X3F30
N500G00X45
N510X100Z100
第三次斯沃实验：
上机----此次零件需要掉头加工车削鋽头加工毛坯98.2，半径50
O1003
T0101
G0X100Z100
M3S650
G0X52Z2
G71U1.5R0.5
G71P70Q130U0.6W0.1F100
N70G0X0
G1Z0
X32
X36Z-2
Z-19
X44
W-3
N130G3X48.398W-8.872R19
G70P70Q130F80
N130G0X100Z100
M30
第一步加工后，点击：
“工件操作—工件掉头”
运行下个程序：
（注意：
对刀是第三把：
G003右边目录，不是第二把刀，不要把它输入到G002中。
：
x49.28mm，Z0）
O1004
T0101
G0X100Z100
M3S650
G0X52Z2
G71U1.5R0.6
G71P70Q150U0.6W0.1F100
N70G0X0
G1Z0
X16
X20Z-2
Z-26
X24W-2
W-12
G2X30W-16R24
G1X37.868
N150G3X48.398W-13.128R19
G70P70Q150
G0X100Z100
T0303
G0X22Z2
G92X19.2Z-21F1.5
X18.6
X18.2
X18.04
G0X100Z100
M30
加工图（略）
华夏考试零件图如下：
四把刀
O1003
N10T0101
N20G0X100Z100
N30M3S650
N40X52Z2
N50G71U1.5R0.5
N60G71P70Q190U0.5W0.1F100
N70G0X0
N80G1Z0F80
N90X17
N100X19Z-1
N110Z-10
N120X29
N130G3X34Z-14R4.45
N140G1Z-32
N150X38
N160G3X42Z-34R2
N170G1Z-48
N180X46Z-50
N190Z-50
N200G70P70Q190F80
N210G0X100Z100
N220T0404M3S600
N230G0X44Z-37
N240G73U3R5
N250G73P260Q290U0.3W0F60
N260G1X42Z-37
N270G2X38Z-48R16
N280G1X42
N290X46Z-50
N300G70P260Q290M3S800
N310G0X100Z100
N320M30
掉头后
N10T0101
N20G0X100Z100
N30M3S650
N40X52Z2
N50G71U1.5R0.5
N60G71P70Q140U0.5W0.1F100
N70G0X0
N80G1Z0F80
N90X27
N100X30Z-1.5
N110Z-20
N120X42
N130X46Z-22
N140Z-48
N150G70P70Q140F80
T0303M3S500
G0X32Z3
G92X29.2Z-18F1.5
X28.6
X28.2
X28.04
G0X100Z100
T0202M3S450
G0X48Z-20
G1X25F30
G00X27
G1X30W1.5
G00X100Z100
M30
题④
N10T0101
N20G0X100Z100
N30M3S650
N40X47Z2
N50G71U1.5R0.5
N60G71P70Q170U0.5W0.1F100
N70G0X0
N80G1Z0F80
N90X16
N100X20Z-2
N110Z-20
N120G3X24Z-22R2
N130G1Z-30
N140G2X32Z-45R20
N150G1Z-51
N160X40
N170Z-74
N180G70P70Q170M3S800
N190G0X100Z100
N200T0202M3S600
N210G0X26Z-20
N220G1X16F30
N230G0X26
N240Z-30
N250G1X20F30
N260G0X42
N270Z-62
N280G1X32F30
N290G0X42
N300X100Z100
N310T0303
N320G0X22Z3
N330G92X19.4Z-18F1.5
N340X18.9
N350X18.54
N360G0X100Z100
N370T0202
N380G0X42Z-72
N390G1X3F30
N400G0X45
N410X100Z100
N420M30
题⑤
O4558
N10T0101
N20G0X100Z100
N30M3S650
N40X47Z2
N50G71U1.5R0.5
N60G71P70Q180U0.5W0.1F100
N70G0X0
N80G1Z0F80
N90X7
N100G3X20Z-10R15
N110G1X24Z-12
N120Z-35
N130X27
N140X30Z-36.5
N150X30Z-42
N160G2X35Z-47R5
N170G1X40
N180Z-64
N190G70P70Q180M3S800
N200G0X100Z100
N210T0202M3S600
N220G0X26Z-35
N230G1X20F30
N240G0X26
N250X100Z100
N260T0303
N270G0X26Z-8
N280G92X23.2Z-33F1.5
N290X22.6
N300X22.2
N310X22.04
N320G0X100Z100
N330T0202
N340G0X42Z-62
N350G1X3F30
N360G0X45
N370X100Z100
N380M30
（切槽刀宽4mm）程序如下：
o0065
N10T0101;
N20G00X100Z100;
N30M03S800;
N40G00X46Z2;
N50G71U1.5R0.5;
N60G71P70Q180U0.6;
N70G01X0F80;
N80Z0;
N90G03X20Z-10R10;
N100G02X30W-5R5;
N110G01X29.85
N120W-33;
X32;
W-9;
G02X38W-3R3;
G01X42;
N180Z-71;
N190G70P70Q180M03S1200;
N200G00X100Z100;
N220T0202;
N230M03S500;
N240G00X30Z-48;
N250G01X26;
N260G00X30;
N270W4;
N280G01X26;
N290X30W2;
N300G00X28;
N310X100Z100;
N320T0303;
N330M03S400;
N340G00X30Z-15;
N350G92X29.2Z-43;F1.5;
N360X28.6;
N370X28.2;
N380X28.04;
N390G00X100Z100;
N400T0202;
N410G00X43Z-69;
N420G01X3F30;
N430G00X45;
N440X100Z100;
T0101;
G00X100Z100;
M03S800;
X29Z-48
G03X32W-1.5R1.5;
G00X100Z100;
M30
o4573
N10T0101;
N20G00X100Z100;
N30M03S800;
N40G00X46Z2;
N50G71U1.5R0.5;
N60G71P70Q200U0.6;
N70G00X0
N80G01Z0F80
N90X20
N100X24W-2
Z-20
X28W-2
Z-30
X25Z-42
Z-50
X26
G03X30W-2R2
G01W-8
X40W-6
N200Z-78
G70P70Q200M3S800
G00X100Z100
T0404M3S600
G00X30Z-30
G73U3R5
G73P270Q280U0.3W0F60
N270G01X28Z-30
N280G02X25W-12R15
G70P270Q280M3S800
G00X100Z100
T0202M3S500
G00X26Z-20
G01X20F30
G00X26
W2
G01X20
X24W2
X26
X100Z100
T0303M3S500
G00X26Z2
G92X23.2Z-15F2
X22.6
X22.2
X22.04
G00X100Z100
T0202M3S500
G00X42Z-76
G01X3F30
G00X46
X100Z100
M30
o4572（四把刀：
如以前所诉，不再重复）
N10T0101;
N20G00X100Z100;
N30M03S800;
N40G00X46Z2;
N50G71U1.5R0.5;
N60G71P70Q210U0.6;
N70G01X0F80;
N80Z0;
N90G03X16W-8R8;
N100G01X20.85;
N110X23.85W-2;
W-20
X26
W-3
X32
W-15
W-6
G01Z-64
X33
G03X41W-4R4
N210G01Z-77
N220G70P70Q210M03S1200;
N230G00X100Z100;
N240T0404M3S600
G00X28Z-32
G73U3R5
G73P280Q290U0.3W0F60
N280G01X26Z-33
N290G02X32Z-46R25
N300G70P280Q290M3S800
N310G00X100Z100
N320T0404M3S600
N330G00X33Z-49
N340G73U3R5
G73P360Q370U0.3W0F60
N360G01X32Z-48
N370G02W-6R5
G70P360Q370M3S800
G00X100Z100
T0202S500
G00X28Z-30
G01X20
W1
X20
G00X28
X100Z100
T0303M3S500
G00X26Z-8
G92X23.2W-19F2
X22.6
X22.2
X22.04
G00X100Z100
T0202M3S500
G00X42Z-76
G01X3F30
G00X46
X100Z100
M30
零件42*55，毛坯45*100mm
N10T0101;
N20G00X100Z100;
N30M03S800;
N40G00X46Z2;
N50G71U1.5R0.5;
N60G71P70Q150U0.6;
N70G01X0F80;
N80Z0;
N90G03X24W-12R12;
N100G01W-看不清不知道
N110G01X多少%第一个台阶
N120X23.85W-2;%第一此倒角
N130W-看不清%到达（切槽处）
N140X42
N150Z-60%看不清切削光轴表面，多切一点
N160G70P70Q150M03S1200;
N170G00X100Z100;
T0202S500切槽
G00X28Z-30
G01X20
W1
X20
G00X28
X100Z100
N250T0404M3S600
N260G00X24Z-49
N270G73U3R5
G73P360Q370U0.3W0F60
N360G01XZ-圆弧起点
N370G02W-6R%圆弧的终点坐标
G70P360Q370M3S800
G00X100Z100
T0202M3S500
G00X43Z-59
G01X3F30
G00X43
X100Z100
M30
教你破解斯沃数控软件
很多同学问我要现成的注册码，＆很明确的告诉你没有！
！
！
。
只能自己用软件提取内存数据破解了。
下面我就跟大家哦说一下破解方法：
1.下载安装“十六进制编辑器WINHEX。
2.点击图标
打开斯沃数控仿真软件
3.
4.点击“单机版”，在下拉菜单中选择数控系统，默认为“南京华兴WA310M/WA320iM”。
再选择“机器码加密”，点击“运行”。
出现以下注册提示对话框：
5.选中序列号框内的数字序列号并复制，点击“OK”，出现以下提示框：
（切记这时不要点击确定，否则无法提取内存数据来完成破解）
6.点击图标：
7.运行WINHEX，
8.
9.分别点击“工具”，“打开RAM内存”
10.此时出现如下窗口：
11.
12.向下拖动滚动条
13.
14.双击“Ttplayer#4084”对话框变成如下：
15.选择“PrimaryMemory”，并点击“OK”
16.
17.此时计算机开始提取内存数据，稍等一会儿，WINHEX出现如下界面：
18.分别点击工具栏中的“搜索”，“查找文本”
18.弹出如下对话框，现在将刚才复制的序列号粘贴到第一个框中，并点击“OK”：
19.一会儿功夫就出现下列情况（光标在刚才复制的序列号上闪烁）：
此时按键盘上的‘F3’软件向下查找
20.直到出现“MachineID5322511352915989Serial7D90E169A0F55EE576441C”
20.用鼠标将“Serial”后面的数字（如7D90E169A0F55EE576441C）就是我们苦寻的注册号了选中
，同时按住键盘上的Ctrl和C就将其（如7D90E169A0F55EE576441C）复制了
21.回到斯沃仿真提注册示框
。
点击确定，并粘贴刚才复制的注册号到注册框点击“OK”出现以下状况就破解成功了：
哈哈哈哈哈哈。
。
22.某些仿真机床很顽固，一次破解只能用一次，下次使用时又要求注册！
不过你学会了本教程也不会觉得麻烦。
！
最后祝您破解成功！
！
！
升级会员 