AMADA激光切割G代码说明.docx

AMADA激光切割G代码说明.docx

《AMADA激光切割G代码说明.docx》由会员分享，可在线阅读，更多相关《AMADA激光切割G代码说明.docx（6页珍藏版）》请在冰豆网上搜索。

AMADA激光切割G代码说明

AMADA激光切割G代码说明

定位                                                                                

G00X_Y_Z_E_                                                                          

X:

X-坐标值            Z:

Z-坐标值                             

直线移动                                                             

G01X_Y_Z_A_S_F_P_Q_E_                                                

X-坐标值            F:

加工速度                                    

Y:

Y-坐标值            P:

脉冲频率                                    

Z:

Z-坐标值            Q:

脉冲负载率                                  

A:

角度                         E:

切削条件                           

S:

输出                                                               Y:

Y-坐标值            E:

切割条件  

顺时针圆弧                                                           

G02X_Y_Z_I_J_R_A_S_F_P_Q_E_                                          

X:

终点X-坐标值                                                      

Y:

终点Y-坐标值                                                      

Z:

终点Z-坐标值                                                      

I:

从起点到圆弧中心X方向的距离                                        

J:

从起点到圆弧中心Y方向的距离                                        

R:

圆弧半径                                                           

A:

角度                         P:

脉冲频率                           

S:

输出                        Q:

脉冲负载率                          

F:

加工速度                 E:

切削条件                               

逆时针圆弧                                                           

G03X_Y_Z_I_J_R_A_S_F_P_Q_E_                                          

X:

终点X-坐标值                                                      

Y:

终点Y-坐标值                                                      

Z:

终点Z-坐标值                                                      

I:

从起点到圆弧中心X方向的距离                                        

J:

从起点到圆弧中心Y方向的距离                                        

R:

圆弧半径                                                           

A:

角度                         P:

脉冲频率                           

S:

输出                        Q:

脉冲负载率                          

F:

加工速度                 E:

切削条件                               

闭锁时间                                                             

G04X_                                                                

X:

时间（单位=秒）                                                    

自动再定位装置                                                       

G05I_J_K_                                                            

I:

夹具1移动位置         K:

设定原料命令                              

J:

夹具2移动位置                

精确停止检查                                                         

G09                                                                  

卸载                                                                 

G10X_                                                                

X:

原料X轴方向的大小                                                  

原料执行命令                                                         

G10X_Y_Q_M_                                                          

X:

原料尺寸X                                                          

Y:

原料尺寸Y                                                          

Q:

真空方法                                                           

 （0:

Pad/1:

电器/2:

Pad+电器/3:

夹具）                                    

M:

卸载器类型                                                         

在自动取出装置内部的Tandem设备类型,在三菱（松下）                   

环境下自动取出装置类型可用                                           

自动取出命令                                                         

G18X_Y_I_J_P_K_P_Q_M_                                                

X:

图样终点X坐标                                                    

Y:

图样终点Y坐标                                                    

I:

从冲切（路径）最终坐标到TK左端的距离X                             

J:

TK的真空范围                                                      

K:

YDistancefromPunch（Path）LastCoordinateYtoTKStd.Position   

P:

搁板编号                                                           

Q:

真空方式（0:

Pad/1:

电器/2:

Pad+电器/3:

夹具）                       

M:

M-codeofCancelVacuumRow                                        

穿孔命令                                                             

G24S_P_Q_R_L_                                                        

S:

激光输出             R:

穿孔时间                                   

P:

脉冲频率             L:

穿孔执行/存储                              

Q:

脉冲负载率                                              

自动再定位2                                                         

G25X_（Y_）                                                            

X:

移动距离X         Y:

移动距离Y                                   

自动再定位1                                                         

G27X_（Y_）                                                           

X:

移动距离X         Y:

移动距离Y                                   

输入偏移量                                                           

G30P_R_                                                              

P:

偏移编号            R:

偏移量 

辅助气体选择                                                         

G31I_J_P_Q_R_T_                                                      

I:

用于穿孔的辅助气体选择                                             

J:

用于穿孔的气流选择                                                 

P:

辅助气体选择                                                       

Q:

气流选择               T:

气压                                     

R:

气体精馏时间                                                       

Z-轴模拟模式                                                         

G32P_L_                                                              

P:

基本再定位          L:

Z轴模拟模式存储                             

取消Z-轴模拟模式                                                    

G33                                                                  

跳过功能                                                             

G38X_Y_Z_F_                                                          

X:

X-坐标值            Z:

Z-坐标值                                    

Y:

Y-坐标值            F:

速度                                        

取消切割路径补偿                                                     

G40                                                                  

切割路径补偿到路径左侧                                               

G41D_                                                                

D:

更正编号  

切割路径补偿到路径右侧                                               

G42D_                                                                

D:

更正编号  

TK执行                                                              

G48X_Y_I_J_A_B_S_Q_K_R_M_                                            

X:

最终切割X坐标        S:

排样图样                                 

Y:

最终切割Y坐标        Q:

真空方式                                 

I:

TK基准点X坐标       K:

真空图样                                 

J:

TK基准点X坐标       R:

取消一排真空图样                         

A:

产品基准点X坐标      M:

搁板箱编号的M代码                        

B:

产品基准点Y坐标                      

返回原点                                                             

G50                                                                  

精确停止检查模式                                                     

G61                                                                  

有效的自动倒角/重叠                                                  

G62                                                                  

连续切割模式                                                         

G64                                                                  

多件加工X                                                           

G75W_Q_                                                              

W:

宏编号             Q:

加工起始位置                                 

多件加工Y                                                           

G76W_Q_                                                              

W:

宏编号             Q:

加工起始位置                          

选择绝对值编程                                                       

G90                                                                  

选择相对值编程                                                       

G91                                                                  

建立坐标系                                                           

G92X_Y_Z_                                                            

X:

X-坐标值            Z:

Z-坐标值                                    

Y:

Y-坐标值                                    

原值偏置                                                             

G93X_Y_Z_                                                            

X:

X偏置值             Z:

板厚偏置                                    

Y:

Y偏置值                                                            

多件加工-原点设定                                                  

G98X_Y_I_J_P_K_D_Z                                                   

X:

基准点X-坐标值                 P:

X轴方向量                       

Y:

基准点Y-坐标值                 K:

Y轴方向量                       

I:

X轴方向间隔                     D:

校正值                          

J:

Y轴方向间隔                             

圆柱补偿                                                             

G107A_                                                               

A:

角度                                                               

SQ/RE/RR/角R                                                         

G111X_Y_I_J_K_Q_R_C_H_A_M_                                           

X:

孔中心X-坐标值                   R:

角R                          

Y:

孔中心Y-坐标值                   C:

角C                          

I:

长度                              H:

微连接宽度                    

J:

宽度                              A:

穿孔有/无                    

K:

角度