量测系统评估作业指导书02版.docx
《量测系统评估作业指导书02版.docx》由会员分享,可在线阅读,更多相关《量测系统评估作业指导书02版.docx(24页珍藏版)》请在冰豆网上搜索。
量测系统评估作业指导书02版
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
2/14
1.Purpose目的:
Toevaluatethecapabilityofmeasuringequipment/gauge.
評估儀器的量測能力。
2.Scope範圍:
ApplicabletoCWTmeasuringequipment.
適用於所有CWT的量測儀器。
3.Responsibility權責:
所有CWT量測儀器。
4.Definition定義:
4.1Gauge量具:
Gaugementionedinthisdocumentcoversallmeasuringequipment,toolsandmeterswhichare
usedtomeasureortestprocess/productcharacters.
此文件所提到的量具(gauge),泛指檢測製程或產品特性所用的量測儀器或工具而言。
4.2Stability穩度:
Thedifferencebetweentheobservedaverageofmeasurementsobtainedwithagaugeonthesame
masterormasterpartswhenmeasuringasinglecharacteristicoveranextendedtimeperiod.
是指同一量測系統,在不同的時間量測同一工件的同一特性時,其平均值所產生的差異。
4.3Accuracy準度:
Thedifferencebetweentheobservedaverageofmeasurementsandthemastervalue.Themaster
valuecanbedeterminedbyaveragingseveralmeasurementswiththemostaccuratemeasuring
equipmentavailable.
是指量測之平均值與真值所產生的差異,如果真值不易取得,可挑選最精密的量測系統,並
以其量測平均值取代之。
4.4Linearity線度:
Thedifferenceintheaccuracyvaluesthroughtheexpectedoperationrangeofthegage.Common
causevariabilityaffectinglinearityoriginatesprimarilyfromtwosources:
Accuracyand
Repeatability.
是指量測系統在合理的工作區間內,其準度所產生的差異,一般而言準度和重複性會直接影
響線度的好壞。
4.5R&R重複性與重現性:
Repeatabilityandreproducibility.
gaugerepeatabilityisthevariationinmeasurementsobtainedwhenoneoperatorusedthesamegauge
formeasuringtheidenticalcharacteristicsofthesameparts.Gaugereproducibilityisthevariationin
theaverageofmeasurementsmadebydifferentoperatorsusingthesamegaugewhenmeasuring
identicalcharacteristicsofthesameparts.
@ControlledDocument@ChantWorldTechnology@CompanyRestricted
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
3/14
重複性是指固定的操作員使用同一量具,量測同一工件的同一特性時,所產生的量測變異。
重現性是指不同的操作員使用同一量具,量測同一工件的同一特性時,所產生的平均量測變
異。
4.6Characteristicspec.特性規格:
Themoninalvalueandtoleranceusedasthespec.ofoneorsomecharacteristicstobemeasured,
normallyit’stheproductspecification.
評估量具量測能力時所用的規格,也就是所欲評估產品特性的該項特性之產品規格。
4.7USL&LSL:
USL–Uppercharacteristicspec.limit.
LSL–Lowcharacteristicspec.limit.
USL–特性規格的上限。
LSL–特性規格的下限。
4.8Tolerance容差:
Thetotalallowanceofcharacteristicspec.
E.G.characteristicspec.is100±1thenistoleranceis2.
指特性規格的容許範圍。
例如:
特性規格為100±1,則其容差為2。
4.9EV:
Repeatability–EquipmentVariation.
重複性–設備變差。
AV:
Reproducibility–AppraiserVariation.
再現性–評價人變差。
R&R:
Repeatability&Reproducibilityvariation.
重複性和再現性變異。
PV:
PartVariation.
零件變差。
TV:
TotalVariation.
總變差。
4.10PTC:
Percenttoleranceconsumedbyrepeatabilityandreproducibility.Thesmaller,thebetter.
PTC=(5.15×SDRR)/tolerance,basedon99%confidencelevel.
PTC:
(Percenttoleranceconsumed)佔有率。
指由量具的重複性及操作的重現性所引起的量測變異之佔有率,此佔有率(PTC)的值當然
是愈小愈好。
PTC=(5.15×SDRR)/容差(根據99%的信賴水準而言)。
@ControlledDocument@ChantWorldTechnology@CompanyRestricted
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
4/14
BILATERALSPEC.
雙邊規格
ONLYUSL
只有上限規格
ONLYLSL
只有下限規格
CHARACTERISTICSPEC.
特性規格
Y±y
M±(USL–M)
M±(M-LSL)
USL
Y+y
USL
2M–LSL
LSL
Y-y
2M–USL
LSL
TOLERANCE容差
2y
2(USL–M)
2(M–LSL)
4.11Gaugecp:
Equipmentcapabilityindex.Precision.It’sameasureofconformancetocharacteristicspec.,andis
calculatedbyT/(5.15×R&R)casedon99%confidencelevel,whereTisthetoleranceof
characteristicspec.It’sjustreciprocalofPTCofR&R.
GAUGECP=1/PTC.
GAUGECP:
量具的量測能力指數,只限於精度。
GAUGECP=1/PCT=T/(5.15×R&R)
其中T是特性規格的容差
4.12GAUGECPK:
Equipmentcapabilitytoindexprecisionplusaccuracy.It’salsoameasureofconformanceto
characteristicspec.,andisobtainedbythecalculationof(USL–MEAN)/2.575×R&R.And
(MEAN–LSL)/2.575×R&Rbasedon99%confidencelevel.Thentakethesmallerone.WhereUSL
istheupperlimitofcharacteristicspec.,andLSListhelowerlimitofcharacteristicspec.gauge
CPKisapplicableonlywhenstandardisusedforgaugeR&Revaluation.
GAUGECPK:
量具的量測能力指數,包括精度及準度。
GAUGECPK=(USL–平均值)/(2.575×SDRR)
或(平均值–LSL)/(2.575×SDRR)
兩者取其較小者
其中USL是特性規格的上限,LSL是特性規格的下限,但GAUGECPK只有在使用標準件
當作被測物評估時,才求得到。
5.Contents作業內容:
5.1Determinationofcharacteristicspec./USL&LSL/tolerance):
特性規格/USL&LSL/容差的決定:
5.1.1Evaluationusingrealproducts當使用真實產品作評估時,有雙邊的產品規格,產品只具單
邊
@ControlledDocument@ChantWorldTechnology@CompanyRestricted
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
5/14
BILATERALSPEC.
雙邊規格
ONLYUSL
只有上限規格
ONLYLSL
只有下限規格
CHARACTERISTICSPEC.
特性規格
X±y
X±(USL–M)
X±(M-LSL)
USL
X+y
USL
2X–LSL
LSL
X-y
2X–USL
LSL
TOLERANCE容差
2y
2(USL–X)
2(X–LSL)
5.1.2Evaluationusingstandard(standardvalueisx)當使用標準件作評估時(X為標準件標準值)
5.1.3REMARK備註:
(1)Mismean.M是指平均值。
(2)Knownstandardselected已知標準件的選擇:
Thestandardvaluemustbeasclosetorealproductvalueaspossible.Inprinciple,
│X-Y│/Y<50%forbilateralproductspec.and│X-Y│/Y<10%forunilateralproduct
spec.isneeded.
標準件的標準值(X)應該盡可能接近實際待測產品的公稱值(Y)其基本原則是
│X-Y│/Y<50%針對產品有雙邊規格。
│X-Y│/Y<10%針對產品只具單邊規格。
5.2Evaluationstandardandgaugeresolution標準件之精準度及量具之最小讀數:
Ifastandardisusedtoevaluatetheequipmentcapability.Ithastobemoreaccuratethanevaluated
equipmentatleastby4times.Theresolutionofevaluatedequipmenthastobesmallerthanthe
toleranceofcharacteristicspec.atleastby6times.
使用標準件作為評估時,則所選標準件之精準度必須比量具之精準度至少要好4倍,量具的
最小讀數最多不得大於特性規格的容差之六分之一。
5.3Evaluationfrequency評估頻率:
Besidesnormalcalibration,measurementsystemevaluationshallbedoneonceperyearformajor
measurementequipmentusedtomeasurethequalityofproductormaterial.Theevaluationresults
maybeusedasareferencetodetermineequipmentcapabilityandcalibrationinterval.
針對量測產品材料的重要量具而言,須每年作一次measurementsystem的評估,評估結果可以
作為決定量具能力及校正頻率之參考。
@ControlledDocument@ChantWorldTechnology@CompanyRestricted
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
6/14
5.4GAUGER&Revaluationprocedure的評估流程:
5.4.1PleaserefertoattachmentI:
GAUGER&REVALUATIONFLOW.
請參考附件I的評估流程。
5.4.2PartA:
Evaluationusingrealproductsormeasuredparts.
A部份:
使用真實產品或工作評估時。
A-1Decidethecharacteristicspec.seeitem5.
決定特性規格,參考項目5。
A-2SelectfiveormorepartsandidentifytheninsequentialnumberforR&Revaluation.Let
P=selectedpartsquality.IfdestructivetestisunavoidableforthisR&Revaluation.The
sametruevalueofthesefiveormorepartsisnotamust,butthetruevalueofeach
evaluationonindividualnumberoftestshouldbeasmuchasclose.
選擇5個或5個以上的產品作為評估的待測物,並加以編號,設P是所選的產品數
目,若為破壞性檢測,則選擇P組產品,每組內的產品變異應盡量縮小。
A-3Choosetwoorthreeappraisers,thosewhoordinarilyperformthismeasurementare
preferableandlotA=chosenappraisers’number.
選擇2個或3個評鑑者,平時作該項檢測者是最適當的人選,A是所選出的評鑑者
人數。
A-4Eachappraise,usingthesameGAUGEtobeevaluated,measuresthepartsbyfollowingthe
proceduresbelow:
每一位評鑑者使用待評估的該量具,按如下的安排作評估:
A-4-1Issuerecordingformtoappraisersincludingfirsttrial,secondtrial,…theI-thtrial
recordingform,butnormally2or3trialsareenough.Theformofeachtrialhastobe
separated.Thenumber1-10initisjusttheproductnumberhere.
發量測記錄紙給評鑑者,包括第一次量測、第二次量測…,第I次量測的記錄紙
,一般二次或三次即可,但每次量測的選錄紙應予公開。
此量測記錄紙的號碼1-
10代表產品的編號。
A-4-2Appraiserafirstfinishthemeasurementonapiecesofproductsrandomly,andrecords
themontherelevantcolumnsofthefirsttrialform.Handtherecordstohismaster.
評鑑者A先把P個產品隨機量完,並把結果按產品編號記錄在第一次量測記錄紙
的相對欄內,把此第一次量測記錄紙交予主管。
A-4-3AppraiserBdoesthesameasA-4-2.
換評鑑者B同A-4-2的步驟,隨機量測相同的P個產品。
@ControlledDocument@ChantWorldTechnology@CompanyRestricted
CWT
清盛電子股份有限公司
部門:
品保部
O.I.DOFMEASUREMENTSYSTEMANALYSIS
量測系統評估作業指導書
編號:
CWW-VQA-601
制訂日期
88/04/16
版本
02
頁數
7/14
A-4-4AppraiserCdoesthesame,too.It’somitted,shouldonly2appraisersbechosen.
換評鑑者C,同A-4-2的步驟,隨機量測相同的P個產品,若只選兩位評鑑者
的話,則此項省略。
A-4-5Let’sbacktotheappraiserAanddoitalloveragainasA-4-2.Buteverythingisjust
forthesecondtrial.
再重新回到評鑑者A,同上之步驟把P個產品隨機量完;並把結果按產品編號記
錄在第二次量記錄紙的相對應欄內,也把此第二次量測記錄紙交予主管。
A-4-6AppraiserBdoesthesameasA-4-5.
換評鑑者B同A-4-5之步驟。
A-4-7AppraiserCdoesthesame,too.Thisisomitted,shouldonly2appraisersbechosed.
換評鑑者C同A-4-5之步驟,若只選2位評鑑的話,則此項省略。
A-4-8Shouldbethirdtrialneeded,itemsA-4-2toA-4-4would3repeatedjustit.
Thepurposeofabovementionedarrangementistomakesurethat:
·Appraisershandletheminarandomorder.
·Appraisersshouldnotseeeachother’sreadings.
·Appraisershasnochancetorefertohispreviousreading.
AsregardstodecimalplacetakenforGAUGEinlinearscale,recordreadingtoone
moredecimalplacethanthegaugeleastcountwillbefollowed.Forinstance,record
willbereadto0.001mm,shouldtheleastcountbe0.01mm.
若要多反覆量測一次,則重複A-4-2到A-4-4的步驟,只是結果按產品編號記錄
在第三次量測記錄紙的相對應欄內。
以上評估的安排,目的是要讓每位評鑑者能隨機評估產品,同時不會參考到別人
的答案,也不會參考到自己前次評估的答案,至於針對線性讀值的量具,數值要
取到有效位數。
例如:
若線性量具的最小刻劃是0.01mm,則值應取到0.001mm。
A-5Theappraisers’masterorhisrepresentative,putsallofreadingsandUSL/LSLinto
computersoftwareifavailableforcalculationandanalysis.