出厂标准.docx
《出厂标准.docx》由会员分享,可在线阅读,更多相关《出厂标准.docx(29页珍藏版)》请在冰豆网上搜索。
出厂标准
wincore
CV01CULTIVATORQUALITYSPECIFICATION
CV01质量规格
Tobeusedformodels:
使用于以下型号
CV01
Index检索
1.0GENERAL总则
2.0SAFETY安全规则
3.0APPEARANCE外观
4.0MARKING/GRAPHICS/LABELS(PRODUCT)标记/图形/标贴(产品)
5.0CONSTRUCTION结构
6.0ELECTRICALPERFORMANCE电器性能
7.0MECHNICALPERFORMANCE机械性能
8.0LIFETESTING寿命测试
9.0PACKAGING包装
10.0QUALITYTESTPLAN质量测试计划
11.0INSPECTIONANDTESTRESULT检查及测试结果
1.0
General总则
Thisqualityapprovalandinspectiondocumentestablishesuniformqualitystandardsforevaluationofthecompliance,performance,construction,appearance,reliability,andpackagecharacteristicsofthisproduct.
本检查文件是基于评价这款产品的统一质量标准而制定,包括产品一致性,性能,结构,外观,可靠性及包装特性等方面
1.1InspectionofcharacteristicsshouldbeperformedtotheANSI/ASQCZ1.4-1993samplingplan.Refertogeneralinspectionlevel2,Singleplanunlessotherwisespecifiedwithinthisdocument.TheAQLlevelwillbebasedonthefollowingcriteria:
/ANSI/ASQCZ1.4-1993
1.1特性检查应按照“美国国家标准学会/美国质量控制学会”(简称ANSI/ASQC)Z1.4-1993抽样检验方法。
参考通用检查标准2,单一计划,除非本文件另有说明。
AQL水平基于下列标准:
AQL0:
Tobeusedforinspectionofcriticaldefects.Acriticaldefectisanydefectthatwouldresultinseriousorfatalinjurytoanypersonusingthisproduct.Alsoanydefectordefectsthatwouldresultinacustomerreturningtheproduct.
AQL0:
用于检查致命缺陷,致命缺陷是指使用本产品会导致对人产生重大或致命伤害。
还包括导致顾客退货的缺陷。
AQL1.5:
Tobeusedforinspectionofmajordefects.Amajordefectisanydefectthatwouldaffecttheperformance,reliability,orappearanceoftheproduct.Alsoanydefectwhichwouldleadtocustomerdissatisfaction.
AQL1.5:
用于检查主要缺陷,主要缺陷是指影响本产品的性能,可靠性或外观的缺陷。
还包括导致顾客不满意的缺陷。
AQL2.5:
Tobeusedforinspectionofminordefects.Aminordefectwouldbeanysmallappearance,orworkmanshipdefectthatwouldnotlikelyresultinacustomerreturnornon-salableproduct.
AQL2.5:
用于检查次要缺陷,次要缺陷是指小的外观缺陷或作工缺陷,不会导致顾客退货或造成产品不适合销售的缺陷。
1.2Allsamplesselectedmustbeselectedusingstandardsamplingcollectionpractices.Samplingshouldbecollectedatrandomfromdifferentsectionsorareasofthecontrolledlot.
1.2所有抽样必须按照标准抽样办法进行,应从不同批次,不同范围,不同部分随机抽取样品。
1.3Productmustcomplywithallrelevantcomplianceagencystandards.Itistheresponsibilityofthefactorytounderstandthelatestlevelofstandardsandanyadditionalstandardsthatmayberequired.
1.3产品必须符合相应的标准。
熟悉最新标准及附加标准是工厂的职责。
1.4TheProductmustbeevaluatedtothelatestrevisionoftheengineeringdrawingandproductspecification.Noalterationsfromthestandardsestablishedinthisqualityspecificationcanbeapprovedwithoutwrittenauthorization.
1.4必须用最新版本的工程图纸和产品规格来检查。
未经批准不允许更改本质量检验标准。
1.5AlltestequipmentusedforevaluationofthisproductmustbecalibratedtoNISTstandardsorrelevantlocalgovernmenttestdepartmentstandardsonanannualbasis.
1.5每年所有检验设备必须按照NIST标准或当地政府的指定测试标准进行检定。
1.6Allappearanceinspectionandcolordeterminationistobeconductedundercoolwhite(5000k)andwarmdaylight(7500k)illumination.Theproductshouldbeviewedatadistanceof30cm.Allsurfacesthatarevisibletotheconsumerduringnormaluseoftheapplianceshouldbeinspectedtothecriterialistedabove.
1.6所有外观检查和颜色确定应在冷光(5000K)和日光(7500K)照明下进行。
应以30厘米的距离查看产品。
顾客正常使用本产品时显而易见的表面都要按照上列标准检查。
1.7Allproductsmustcomplywiththerequirementswithinthisspecification.Anylotthatdoesnotmeettheserequirementsshallberejected,thestockquarantinedandre-workeduptoastandardthatisacceptable.
1.7所有产品必须符合本检验标准的要求。
没有达到这些要求的任何批次都应被拒收。
这些货物应隔离并返工,达到标准后才能接受。
2.0Safety安全规则
2.1TheProductmustbefreeofanysharpedgesorcornersthatcouldcauseaskinpunctureorcuttypeinjurywhencontactedduringnormaluseorusermaintenance.
Inspectioncriteria:
AQL0Defecttobeconsideredcriticaldependingonseverity.
2.1当用户正常使用或维护,接触本机时,本机不应有能够导致皮肤刺破或割伤的尖角或锐边。
检查标准:
AQL0.考虑到这是严重的主要缺陷。
2.2Undernocircumstances,willunauthorizedchangesbemadetotheproductthatcouldaffecttheappearance,function,safety,orreliability.Comparisonsshallbemadewiththesignedoffsample.
InspectionCriteria:
AQL0Defecttobeconsideredcritical.
2.2决不允许XX的会影响本产品外观,功能,安全,或可靠性的更改。
制作限度样本以做比较。
检查标准:
AQL0.考虑到这是致命缺陷。
3.0Appearance外观
3.1Theexteriorsurfaceoftheproductmustbefreeofobviousscratches,sinkmarks,moldingmarks,partinglines,excessiveflash,blemishes,contamination,orsimilardefectswhichwouldaffectthesaleability,orcauseaproducttobereturnedbytheconsumer.Signedoffsamplemustbeusedasareference.
Inspectioncriteria:
AQL2.5Defecttobeconsideredminor.
3.1产品外表面不应有擦痕,缩水,成型时的痕迹,过分亮光,分缝线,污点,污染物或类似的影响到销售的缺陷或者导致产品被退回。
签回的样品做参考
检查标准:
AQL2.5考虑到这是次要缺陷
3.2Alledgesandseamsoftheexposedmatingpartsmustfittogetherwithoutanyunsightlyorlargegaps.Matingcomponentedgesmustbefreeofanexcessiveflashormisalignment.
Signedoffsamplemustbeusedasareference.
Maximumgapbetweenpartstobe0.5mm
Maximumacceptablemis-matchbetweensurfacestobe0.5mm
Inspectioncriteria:
AQL2.5Defecttobeconsideredminor.
3.2所有边缘和接缝处要匹配良好,无任何难看的或较大的缝隙。
相结合的零件边缘不应有过分亮光或未对准的情况。
在零部件之间最大缝隙是1MM
在表面之间所能接受的最大错位是1MM
检查标准:
AQL2.5考虑到这是次要缺陷。
3.3Exteriorcolorandfinishmustcomplywiththecolorsamplesestablishedbycustom.Theremustbenocolormismatchbetweenmatingsurfacesofthesamecolorrequirement.Colourplaqueswillbeagreedatthestartofproductionandsignedoff,theseshallbeusedtoaccessproductcolour.Thecolourshallbecheckedinnaturaldaylightandartificiallightsources.
Inspectioncriteria:
AQL2.5Defecttobeconsideredminor.
3.3外部颜色和漆色必须符合客户制定的色板。
相结合的相同颜色的零件表面,颜色必须协调。
在生产开始前确定色板及限度样本,这是确定产品颜色的办法。
应在自然光或人造光源下检查颜色。
检查标准:
AQL2.5考虑到这是次要缺陷。
4.0Markings/Graphics/Labels标记/图形/标贴
4.1TheProductmustbepermanentlymarkedormoldinsertedwithanyapplicablecomplianceagencymarkings.Thismustincludetheproductmodelnumber,ratingsrequirements,complianceagencysymbolsandlistednumbers,andapplicablesafetywarnings.Theengineeringdrawingandrelevantproductspecificationdocumentwillidentifythelocation,layout,andsizeofthisinformation.Markingsmustbeinaccordancewithregulatoryagencystandards.
Inspectioncriteria:
AQL1.5.Defecttobeconsideredmajor.
4.1产品必须做一些标记,或通过模具实现。
这里包括产品型号,额定要求,指定的符号,系列号和适用的安全警告。
工程图纸和相应的产品规格文件会确定位置,布局及尺寸等信息。
标记必须与管理机构的标准一致。
检查标准:
AQL1.5考虑到这是致命缺陷。
4.2Allgraphicsshallbelocatedinthecorrectareaasspecifiedbytheproductspecification.Graphicsmustbealignedverticallyandhorizontallybefreeofanybubbles,loosecorners,orraisededgesGraphicsmustbeinspectedtotheapplicablestandardslistedbelow.
Inspectioncriteria:
AQL2.5Defecttobeconsideredminor.
4.2所有图形标志(贴)应按照产品规格书的要求放在指定位置。
必须垂直和水平放置,不许有起泡,松角,或翘边等情况。
按照下列标准检查图形标志(贴)。
检查标准:
AQL2.5考虑到这是次要缺陷
4.3Adhesiontest:
apieceof3Mbranded600cellophanetapeofadequatelengthtocovertheentiregraphicshallbeplacedoverthegraphicandadheredsecurely.Noportionofthegraphicshallberemovedwhentapeisremovedwithaconstantforceat180-degreepeel.
4.3粘附试验:
用一块600毫米宽足够长的3M胶带纸覆盖在整个图形(贴)上,以恒力180度剥落,图形不应有任何部分脱落。
Cleaningsolutiontest:
allgraphicsmustwithstandbeingwipedtentimeswithacottonballsaturatedwiththefollowingliquids.
WD40,Whitespirit,Petrol,thelabelshallbelefttosoakforaperiodof3minutesthenwipedwithasoftcottoncloth.Thelabelshallnotbedamagedanyform.
Test3pcsfromproductionlot
Inspectioncriteria:
AQL1.5.Defecttobeconsideredmajor.
擦洗试验:
所有图形标志(贴)都应经受10次擦洗试验,方法是用一个棉球浸满下列液体擦拭。
WD40,石油溶剂油,汽油等。
标贴应该浸泡3分钟然后用软布擦拭。
标贴应该没有被破坏
批量里面测试3个
检查标准:
AQL1.5考虑到这是主要缺陷
4.4Everyproductmustbedatedwiththeminimumoftheweekandyearmanufacturedorotherdefinedformat.Thisshouldbeafourdigitdatecodesystemthatpermanentlymarkstheproduct.
Inspectioncriteria:
AQL1.5.Defecttobeconsideredmajor.
4.4每台产品都应有系列号以便跟踪。
这应该印刷在标贴上或机器上其它能够标记的地方。
检查标准:
AQL1.5考虑到这是主要缺陷
5.0Construction构成
5.1Materialsandcomponentsusedintheconstructionoftheseproductsmustbenon-toxic,andcontainnoasbestosormeasurableamountsofthefollowingheavymetals:
Lead,Cadmium,Mercury,Antimony,Barium,Arsenic,HexavalentchromiumorSelenium.Materialsmustbecertifiedbythesupplierstocomplywiththisspecification,andcertificationmustbeavailableuponrequest.AllcomponentswithintheproductmustbeROHScompliant.OnrequestthesuppliermustbeabletoshowthattheproductcomplieswiththerequirementsofROHS.
Inspectioncriteria:
AQL0.Defecttobeconsideredcritical.
5.1用在本产品上的材料和成分必须是无毒的,不含有石棉成分或下列重金属:
铅,镉,汞,锑,
钡,砷,六价铬或硒。
供应商提供的材料一定是被鉴定过的符合本检验标准的。
本产品的所有零件都应
符合ROHS指令要求,如果要求提供证明文件,即可提供
检查标准:
AQL0.考虑到这是致命缺陷
5.2Allfasteners(ex.Screws,nuts,rivets,etc)mustbeproperlyattachedandsecure.Screwsandnutsmustbetightenedtothepropertorquerequirementssetoutinthemanufacturingplan.Rivetsmustbeproperlyrolledover.Removableorreplaceablefastenersmustnotbedamagedtothepointthatremovalofthefastenerisimpossible.
Inspectioncriteria:
AQL1.5.Defecttobeconsideredmajor.
5.2所有紧固件(螺钉,螺母,铆钉等)必须适当可靠地紧固。
螺钉和螺母必须按照制造要求以合适的扭矩紧固。
铆钉必须翻卷铆好。
可移动或可替换的紧固件在可能移动的部位上不能被损坏
检查标准:
AQL1.5考虑到这是主要缺陷
5.3Productmustbefreeofanylooseorforeignmaterialwithintheunitthatcouldcauseanelectricalshortcondition
Inspectioncriteria:
AQL0.Defecttobeconsideredcritical.
5.3产品在内部不应有导致短路的松动或外来部件
检查标准:
AQL0.考虑到这是致命缺陷
5.4Productpowersupplycordmustbecomplywiththerelevantsafetystandard,suchasGS,UL,andSAAetc.
Inspectioncriteria:
AQL1.5.Defecttobeconsideredmajor
5.4产品电源线必须符合相关的安全标准,例如GS,UL和SAA等
检验标准:
AQL1.5被认为主要缺陷
5.5Allinternalsolderconnections(ifused)mustcomplete,clean,smooth,andbright.Solderjointsofconnectingwiremustwithstandaminimumof2KGpullfor5seconds.
Inspect