计算机塑料部件外观检验标准.docx
《计算机塑料部件外观检验标准.docx》由会员分享，可在线阅读，更多相关《计算机塑料部件外观检验标准.docx（24页珍藏版）》请在冰豆网上搜索。
计算机塑料部件外观检验标准
计算机塑料部件外观检验标准
1.SCOPE范围
ThisspecificationdefinesthecosmeticrequirementsforPLASTICPARTSandASSEMBLIESfor
该规格详细说明了Compaq计算机公司对塑料部件和装置的外观要求
CompaqComputerCorporation.Thecosmeticrequirementsshallbedividedintofourclassesin
该外观要求根据部位可分为4类.
accordancetoarealocation.
2.APPLICABLEDOCUMENTS适用文件
Wherethisspecificationreferstoanotherdocument,thatdocumentisoftheissueineffectonthedateof
当该规格引用其它文件时,则此文件发行自受邀命令或要求提议之日起生效
invitationtobidorrequestforproposal.Referenceddocumentsapplytotheextentspecifiedherein.
引用的文件适用于此处规定的范围
3.INSPECTION检测
3.1VISUALINSPECTION目测
Visualinspectionshallbeconductedasfollows:
目测执行如下
3.1.1Lighting灯光
100±20foot-candlescoolwhitefluorescentillumination.
100±20Foot-candle这种型号的冷白荧光灯照明.
3.1.2Position位置
Placetheassembly18.000to24.000（armslength）infrontofpersoninspecting.Thepart
将装置置于检测员前方18.000–24.000（臂长）.
shouldbeheldintwo
（2）positions;paralleltothelightsourceand30degreesfromthelight
部件需置于两种位置:
与光源平行和距光源30度.见图1.
source.SeeFigure1.
3.2POSSIBLEDEFECT可能存在之缺点
Ifapossibledefectisfoundinboththeabovementionedpositions（refertoFigure1）,refertothe
若在上述两种位置情况下都发现有可能存在之缺点（指图1）,
appropriateclassforrejectioncriteria.Possibledefectsfoundoutsidetheviewingparametersshall
参考合适类别的拒收标准.检视限量之外的可能存在缺点可被忽略.
beconsiderednotvisible.
4.DEFINITIONOFCLASSES类别定义
4.1CLASSI类别I
ClassIareasshallbedefinedasareasincontinuousviewoftheoperator.
类别I部位是指操作员可持续观看到的部位.
4.2CLASSII类别II
ClassIIareasshallbedefinedasareasoccasionallyinviewoftheoperator.
类别II部位是指操作员可偶尔观看到的部位.
4.3CLASSIII类别III
ClassIIIareasshallbedefinedasareasseldomseenbytheoperator.
类别III部位是指操作员很少观看到的部位.
4.4CLASSIV类别IV
ClassIVareasshallbedefinedasareasneverseenbytheoperator.
类别IV部位是指操作员从未观看到的部位.
5.ALLCLASSES所有类别
5.1CLEANLINESS清洁
Partsshallbefreeofdirt,grime,grease,andothercontaminants.Dustcausedbyshippingmaterial
部件需无污垢,污点,油脂和其它污渍.
isacceptableifitcanbeblownoffwithairorwipedoff.
由运输材料引起的灰尘若能被吹去或擦去,则可允收.
5.2FLASH毛边
Theheightofanyflashgreaterthan.01isnotacceptable.Whereflashhasbeentrimmed,thecut
任何高度大于0.01的毛边不可允收.修理过毛边的地方,切痕不可除去任何纹路.
marksshallnotremoveanytexture.Anytrimmedsurfaceshallbesmoothwithoutjaggededges.
任何修理过的表面需光滑无锯齿边缘.
5.3MISMATCH错配
Mismatchgreaterthan.01persideisnotacceptable.
错配每边大于0.01不可允收.
5.4SONICWELDS快速焊接
Thegapbetweensonicweldedpartsgreaterthan.01isnotacceptable.
快速焊接部件之间间隙大于0.01不可允收.
5.5GENERAL常规
Shortshots,burns,cracks,nicks,voids,andcrazingarenotacceptable.
注入不足,灼伤,破裂,刻痕,空点和裂纹不可允收.
6.CLASSI类别I
6.1SCRATCHES/ABRASIONS刮伤/磨损
Scratchesorabrasionswhichremovetexturearenotacceptable.
会除去纹路的刮伤或磨损不可允收.
6.2SPLAY轻微裉色
Splayisnotacceptable.
轻微裉色不可允收.
6.3CONTAMINATION污染
Molded-incontaminationgreaterthan.025indiameterisnotacceptable.Anyparticleof
嵌入污染物直径大于0.25不可允收.
contaminationlessthan.01orlessindiameterandwithaminimumdistanceof.50fromanyother
任何直径小于0.01或更小,且距任何其它粒子最小距离为0.50的污染粒子可被忽略.
particleshallbeconsiderednotvisible.Theminimumdistancebetweenanytwo
（2）particlesof
任意两污染粒子之间的最小距离需是2.00英寸.
contaminationshallbe2.00inches.
6.4SINKS凹槽
Sinksgreaterthan.005,whenmeasuredwithadialindicatorwitha.040diametertip,arenot
acceptable.
当用一带有直径为0.040尖端的千分表（刻度盘显示器）测量,凹槽大于0.005不允收.
6.5BLUSH变色
BlushinthisareaisnotacceptablewithoutpriorwrittenapprovalfromCompaqComputer
Corporation.
无事先Compaq计算机公司的尽面认可,该部位变色不允收.
6.6KNITLINES接合线
VisibleknitlinesarenotacceptableinthisareawithoutpriorwrittenapprovalfromCompaq
ComputerCorporation.
无事先Compaq计算机公司的尽面认可,该部位可视接合线不可允收.
6.7COSMETICPAINT外观漆
AllcosmeticpaintedsurfacesshallmeetthecolorrequirementsasdefinedbyCompaq
所有包装喷漆的表面需符合Compaq计算机公司规定的颜色要求.
ComputerCorporation.Allpaintedsurfacesshallbeuniforminglossandfreeofstreaks,runs,flakes,bubbles,orlossoftexturecausedbypaintbuild-up.
所有喷漆表面的光泽面需一致,且无由内建漆引起的条纹,熔化,剥落,空泡,或纹路遗失.
6.7.1Adhesion附着力
Cosmeticpaintshallnotseparatefromthebasematerialwhensubjectedtoadhesiontests
在Compaq计算机公司规定的粘合测试当中,外观漆需不会脱离底料.
specifiedbyCompaqComputerCorporation.Paintshallbecuredcompletelysothatitcannot
喷漆需彻底以使其不会被干布或手指擦去.
berubbedoffbyadryclothorthefingers.Ifanypainttransferstoadryclothorthefingers,
若任何漆被擦到了干布或手指上,则此部位不允收.
thatpartisnotacceptable.
6.7.2Inclusions杂物
Anyinclusiongreaterthan.04indiameterisnotacceptable.Thereshallbenomorethanfour
任何直径大于0.04的杂物不可允收.
（4）inclusionspersurface.Theminimumdistancebetweenanytwo
（2）inclusionsshallbe2.00
每面需不超过4处杂物.任意两处杂物之间的最小距离需是2.00英寸.
inches.
6.7.3PinHoles针孔
Pinholesgreaterthan.01indiameterarenotacceptable.Thereshallbenomorethanfour（4）
直径大于0.01的针孔不可允收.每面不可超过4处针孔.
pinholespersurface.Theminimumdistancebetweenanytwo
（2）pinholesshallbe2.00
inches.
任意两处针孔之间的最小距离需是2.00英寸.
6.7.4Scratches刮伤
Scratchesthatremovepaintarenotacceptable.
会磨去油漆的刮伤不允收.
6.7.5PaintedGroove着色凹槽
Wherepaintoccursonthebottomofthegroove,thereshallbeuniformcoverageonthebottom
在凹槽底部要着色的地方,凹槽底部和内侧需复盖一致.
andinsidewallofthegroove.Theoutsidewallofthegroovemaycontainundersprayaslong
凹槽外侧可包含不足喷漆,只要边线波动每英寸不超过0.02.
asthemasklinedoesnotfluctuatemorethan.02perinch.
6.7.6UnpaintedGroove不着色凹槽
Wherepaintdoesnotoccuronthebottomofthegroove,thereshallbeuniformcoverageupto
在凹槽底部不着色的地方,统一复盖直到凹槽.
thegroove.Theinsidewallofthegroovemaycontainoversprayaslongasthepaintlinedoes
凹槽内侧可包含过量喷漆,只要漆线波动每英寸不超过0.02.
notfluctuatemorethan.02perinch.
7.CLASSII类别II
7.1SCRATCHES/ABRASIONS刮伤/磨损
7.1.1TexturedSurfaces有纹路表面
Scratchesorabrasionswhichremovetexturearenotacceptable.
会磨去纹路的刮伤或磨损不可允收.
7.1.2Non-TexturedSurfaces无纹路表面
Scratchesorabrasionslargerthan.01inchwidex.50inchlongarenotacceptableandnomorethantwo
（2）persurface.
宽大于0.01英寸,长大于0.50英寸的刮伤或磨损不可允收,且每面不可多于两处.
7.2SPLAY轻微裉色
Splayisnotacceptable.
轻微裉色不允收.
7.3CONTAMINATION污染
Molded-incontaminationgreaterthan.025indiameterisnotacceptable.Anyparticleof
嵌入污染物直径大于0.25不允收.
contaminationlessthan.01orlessindiameterandwithaminimumdistanceof.50fromanyother
任何直径小于0.01或更小,且距任何其它粒子最小距离为0.50的污染粒子可被忽略.
particleshallbeconsiderednotvisible.Theminimumdistancebetweenanytwo
（2）particlesof
任意两污染粒子之间的最小距离需是1.00英寸.
contaminationshallbe1.00inches.
7.4SINKS凹槽
Sinksgreaterthan.005,whenmeasuredwithadialindicatorwitha.040diametertip,arenot
acceptable.
用一带有直径为0.040尖端的千分表（刻度盘显示器）测量,凹槽大于0.005不允收.
7.5BLUSH变色
BlushinthisareaisnotacceptablewithoutpriorwrittenapprovalfromCompaqComputer
Corporation.
无事先Compaq计算机公司的尽面认可,该部位变色不允收.
7.6KNITLINES接合线
VisibleknitlinesarenotacceptablewithoutpriorwrittenapprovalfromCompaqComputerCorporation.
无事先Compaq计算机公司的尽面认可,该部位可视接合线不允收.
7.7COSMETICPAINT外观漆
AllcosmeticpaintedsurfacesshallmeetthecolorrequirementsasdefinedbyCompaqComputer
所有外表喷漆的表面需符合Compaq计算机公司规定的颜色要求.
Corporation.Allpaintedsurfacesshallbeuniforminglossandfreeofstreaks,runs,flakes,bubbles,
所有喷漆表面的光泽面需一致,且无由内建漆引起的条纹,熔化,剥落,空泡,或材质遗失.
orlossoftexturecausedbypaintbuild-up.
7.7.1Adhesion附着力
Cosmeticpaintshallnotseparatefromthebasematerialwhensubjectedtoadhesiontests
根据Compaq计算机公司规定在附着力测试中包装漆需不会脱离于底料
specifiedbyCompaqComputerCorporation.Paintshallbecuredcompletelysothatitcannot
喷漆需完善以使其不会被干布或手指擦去.
berubbedoffbyadryclothorthefingers.Ifanypainttransferstoadryclothorthefingers,
若任何漆被擦到了干布或手指上,则此部位不允收.
thatitemisnotacceptable.
7.7.2Inclusions杂物
Anyinclusiongreaterthan.04indiameterisnotacceptable.Thereshallbenomorethanfour
任何直径大于0.04的杂物不可允收.每面不可超过4处杂物.
（4）inclusionspersurface.Theminimumdistancebetweenanytwo
（2）inclusionsshallbe2.00
任意两处杂物之间的最小距离需是2.00英寸.
inches.
7.7.3PinHoles针孔
Pinholesgreaterthan.01indiameterarenotacceptable.Thereshallbenomorethanfour（4）
直径大于0.01的针孔不可允收.每面不可超过4处针孔.
pinholespersurface.Theminimumdistancebetweenanytwo
（2）-pinholesshallbe2.00
inches.
任意两处针孔之间的最小距离需是2.00英寸
7.7.4
Scratches刮伤
Scratchesthatremovepaintarenotacceptable.
会磨去油漆的刮伤不允收.
7.7.5PaintedGroove着色凹槽
Wherepaintoccursonthebottomofthegroove,thereshallbeuniformcoverageonthebottom
在凹槽底部要着色的地方,凹槽底部和内侧需复盖一致.
andinsidewallofthegroove.Theoutsidewallofthegroovemaycontainundersprayaslong
凹槽外侧可包含不足喷漆,只要边线波动每英尺不过0.02.
asthemasklinedoesnotfluctuatemorethan.02perinch.
7.7.6UnpaintedGroove不着色凹槽
Wherepaintdoesnotoccuronthebottomofthegroove,thereshallbeuniformcoverageupto
在凹槽底部不着色的地方,统一复盖直到凹槽.
thegroove.Theinsidewallofthegroovemaycontainoversprayaslongasthepaintlinedoes
凹槽内侧可包含过量喷漆,只要漆线波动每英尺不超过0.02.
notfluctuatemorethan.02perinch.
7.8SPRUEHOLES直浇口
Sprueholesgreaterthan.10indiameterarenotacceptable.Iftheholedoesnotappearcircularin
直径大于0.10的直浇口不可允收.若孔形不圆或边缘锋利,不允收.
shapeorhassharpedges,theholeisnotacceptable.Holeswhichgocompletelythroughthepartare
完全穿透部件的孔不可允收.
notacceptable.
8.CLASSIII类别III
8.1SCRATCHES/ABRASIONS刮伤/磨损
Scratcheswhicharegreaterthan3.00longby.03wideby.01deeparenotacceptable.The
长大于3.00,宽大于0.03,深大于0.01的刮伤不可允收.
maximumnumberofscratchesistwo
（2）.
刮伤处最大数量为2.
8.2SPLAY轻微裉色
Splaygreaterthan.50wid
升级会员 