硬盘录像机.docx

1、硬盘录像机VEHICLE DVRUser Manual This manual introduces the installation and operation procedures of the vehicle DVR system. To ensure proper performance and avoid any faulty operation, please study the manual carefully in advance. Notice: Device input Current is DC24V/12V (3A). Please note AC200V/AC380V

2、 high-voltage power supply should not be applied. 1. Do not place anything on the device.2. Do not touch power supply and device when hand is with water.3. Do not use chemical solution to clean the device. 4. Do not splash water in device, which may short-circuit the device and lead to fire 5. Cut o

3、ff power supply if the device will be not used for long time. Fittings List:NO.Product NameQty (pcs)1Video recorder12Remote Controller13Key14Hydraulic cushion (with fixing screw and aluminum ring)45User manual164 group video input wiring17Power supply input wire18Right angle installation stent49Wiri

4、ng protection box110Four-core camera plug（video input, power supply input）4CONTENTS1. Product Features1) The device adopts patented aseismatic technology for viehcle harddisk: mechanical aseismatic, electronic aseismiatic and software aseismiatic technology. The aseismatic technologies adopted ensur

5、e reliable performance of the device.2) MJPEG adopted ensures high compression ratio and high resolution. 3)The device supports local real-time / non-real time audio/video record and computer playback (via USB). 4)Multi-model video-recording functions: A. Record starts and stops with vehicle. B. Rec

6、ord starts with vehicle and stops 10-30 minutes after the vehicle is stopped. C. Start and stop recording according to preset time.5)Convenient search function: can be searched by date or time.6)Support remote control and 2.5 inches notebook hard disk. 7)Apply floated hydraulic pressure aseismatic s

7、ystem for hard disk. 8)Specially designed long-pin harddisk insertion mode ensures reliable connection. 9)1,2, or 4 Video input can be selected; 1 video output and 1 audio output 10) 836v broad voltage input, 12V, 2A output supply power to video camera or others devices.11)Quartered or full screen.

8、12)With flexible frame, the device can be hanged up or placed flat.13)Protection box prevents the wiring from being damaged.14)Convenient output interface can supply 12v DC power to small TV during testing.15)Unique concentrated audio/video input interface and wiring realize convenient installation.

9、2. Product ParameterParameterDS-2004SystemOperation SystemEmbedded Operation System PSOS Operation InterfacePicture Menu InterfaceOperation ModelRemote ControlAudio-videoVideo Input and output Video Playback formula / standard PAL（625 line, 50 / s）/ NTSC（525 line, 60 / s）Interface ParameterInterface

10、 model：RCA; Input impedance: 75; Input signal: 1.0Vp-pAudio Input and Output InterfaceRCAVideo Compression ModelMJPEGAudio coding method PCMVideoVideo Resources Video4 Real time Recording Audio1 Audio InputReal-time Monitoring ResolutionD1: 704576（PAL）/720480（NTSC）Real-time Monitoring Horizontal Def

11、inition350 TV LineVideo Picture Parameter AdjustmentTonal, Brightness, Contrast, Saturation Video Picture Resolution CIF： 352288（P）/352240（N）Video playback Horizontal Definition 320 TV LineVideo Picture Quality 3 shelf adjustable Video Playback Function Supports PC USB, Local Video Playback, Frame P

12、lay, Slow Play, Quick PlayVideo backup model Mobile Hard Disk Box and High Speed USB2.0 Mobile Memory Video Model1. Record starts with car 2. Record starts and stops automatically at preset times 3. Record starts when car is started by key, and record stops 10min-30min after the key is unplugged.Vid

13、eo Audio Code 4 channels of CIF：1.2-1.5G Byte/ Hour（may changes with video picture）Play Interface ResourcesVideo Interface1 video outputAudio Interface1groupParameterAnti-seismic PerformanceContinuous Working Period8 hours Frequency 0100Hz,Width 10mmVibratory Frequency0100HzVoltage Rating+9VDC+36VDC

14、）Rated Current1A（not include hard disk）Starting Current3AMean Power9W（not include hard disk）Temperature Range -30+65Humidity Range 10%90%Bare Machine Weight1.5Kg Device Size22017558（mm）3. Front Panel, Back Panel and remote controller1) Front Panel (Picture 1)(1) Hard disk box and power supply switch

15、 lock: Insert the key, then turn it to ON, the harddisk case will be locked and device is powered on. Turn it to OFF, the case will be unlocked (and can be pulled out) and device is powered off.(2) IR remote receiver：It receives the infrared signal from remote controller.(3) HDD hard disk status lig

16、ht: Red light on indicates working status of harddisk. The light will be on during video recording and video playing.(4) PWR power supply light：It indicates power on when the light is on.(5) USB interface: It connects with PC and transmits data from the device to PC(6) OUTPUT interface: It connects

17、with monitor, exports video and audio and supplies 12VDC power to small TV.(7) Installation Frame：It is used to support the device during installation.2) Back Panel (Picture 2)(1) POWER interface: After plug in power input wires, you can connect the wires to power positive and negative in vehicle (U

18、sually connect to vehicle battery, with range from 9-36VDC) and ACC trigger voltage (Usually connect to key position or main switch of the vehicle, the range is also 9-36VDC), or connect to timing controller.(2) IN &OUTPUT interface: Audio-video input, Camera power input. After insert audio-video in

19、put wire (as displayed in picture 3), 4 channels of audio-video signal can be inputted via the 4 four-core sockets; at the same time, 12VDC power can be supplied to four cameras. The 4 four-core sockets can be connected to recorder via the 4 four-core camera plugs provided. The four-core camera plug

20、 provided (in picture 4) has four wires: red, black, yellow and white. The four wires should be connected as shown below:A. Red: connect to camera power positive (If you have a tone arm, please also connect to the tone arm power positive) B. Black: connect to camera power positive (If you have a ton

21、e arm, please also connect to the tone arm power negative)C. Yellow: connect to camera video signal output. D. White:（If you have a tone arm, please connect to the tone arm signal output）Notice: This Vehicle DVR only supports the first camera input with audio.(3) Installation hole for wiring protect

22、ion box (picture 5) 3). Remote controller (picture 6) (1) CH1 Full Screen display(2) CH2 Full Screen display (3) MENU: enter or exit menu(4) ENTER: enter or modify menu option(5) STOP: stop video / stop play / move down the cursor after enter menu(6) PLAY: playback video.(7) CH3 Full Screen display(

23、8) CH4 Full Screen display(9) PAUSE, Upper / Pause Playback / Frame Play(10) Left, Back (11) Right, Quick(12) REC, Start video.(13) Four spited picture on screen4. Operation Instruction (main menu) Press to select items, use to enter, press MENU to exit.4-1 System Setup Press to select items, use to

24、 enter, press MENU to exit and save data.(1)Buzzer Alarm Time: setup, 0-30s.(2)Disconnection Alarm：ON/OFF. (3)MOT：Motion Alarm, ON-OFF (4 Types), Front is buzzer Alarm. Behind is jump to alarm picture.(4)Output volume: 00-10. (5)Resolution（Option）：1024768, 10241280,640480,800600(default value 102476

25、8).(6)Software upgrade：Please save updated software in a USB drive. The screen will show both current version and new version of software before upgradingWhen upgrading is in progress, please dont start any other operation or remove the USB drive which may lead to serious system error. After upgradi

26、ng is completed, the system will indicate to restart the unit. During upgrading, hard disk should be available to be served as buffer.4-1-1 Password Setup Press and to select the characters on the screen.Press to confirmIf you want to change your password, please input the original password accordin

27、g to the requirement and then input the new one for twice.default password: 111111.4-1-2 Time SetupPress to select items, use to enter, press MENU toexit and save data. 4-2 Camera Setup Press to select items, use to enter,press MENU to exit and save data.(1)Camera: Camera select (default value CH1).

28、(2)Record setup: video recording is needed or not.(3)BRI/CON/HUE/SAT setup: default value is 5.(4)Sensitivity：sensitivity setup of motion detector:1-4.(5)Auto Switching: Set the duration of each channel: Off, 1 to 10 seconds. 4-3 Record SetupPress to select items, use to enter,press MENU to exit and

29、 save data.(1) Video Record Quality: video quality selection: Highest, High, Normal.(2) Alarm video recording time: start video recording once alarm is initiated. Maximum 30 seconds can be set.4-3-1 Record Speed Press to select items, use to enter, setup. press MENU to exit and save data. 4-4 Record

30、 SchedulePress to select items, use to enter, setup.Press MENU to exit and save data.(1)Use to change record mode.(2)Time range: 0-23 Hours.(3)Set blue for disable the recording. (4)Set red for continuous recording.(5)Set green for motion recording.4-5 HDD Setup Press to select items, use to enter,

31、setup.Press MENU to exit and save data.(1)Overwrite Enabled: Enable overwrite when HDD capacity is full:Yes: Overwrite every four hoursNo: Stop recording(2)HDD Status Indicates current HDD status, including total capacity and percentage of space being used.(3)HDD Format：When choose this item, DVR will request for password.a)