1、附录5如何设置交换机的端口速率双工模式附录5:如何设置交换机的端口速率、双工模式 1附录6:如何关闭交换机的生成树协议及启用端口快速 4附录7:如何设置路由器、交换机的组播 7附录5:如何设置交换机的端口速率、双工模式注:黑体为命令,底纹为注释,斜体为举例。因同一厂家不同型号及同一型号不同版本的 IOS会有所不同,如与本文中介绍有所不同,为正常情况,请参考厂家相关设备技术资料或联系相关技术支持。原则:首先配置端口的速度,然后配置双工模式,千兆端口请参考设备技术手册。CISCO交换机在基于IOS交换机上的配置进入以太网端口 EthernetO/3 的配置模式SwitchenableSwitch#
2、 con figure termi nalSwitch(c on fig)# in terface in terface module/nu mber例:Switch (co nfig)# in terface faO/3Switch(co nfig-if)# speed 10|100|1000 设置端口的速率例:Switch(config-if)# speed 100 将以太网端口 Ethernet0/3 端口速率设置为 100MbpsSwitch(config-if)# duplex full|half|auto 设置以太网端口的全双工 /半双工属性例:Switch(config-if)#
3、 duplex full 将以太网端口 Ethernet0/3 端口设为全双工Switch(config-if)# end 或两次 exitSwitch# copy runnin g-c onfig startup-c onfig返回到特权模式下将配置文件保存到NVRAM 中在基于CatOS交换机上的配置Switch enable进入特权用户Switch (en able) set port speed mod_num/port_ num 10|100|1000|auto 设置端口的速率例:Switch (enable)set port speed 2/3 100 将端口 2/3 的速度设为
4、100MbpsSwitch (en able) set port例:Switch (enable)mod _n um/port_ num full|half 设置端口的双工模式set port duplex 2/3 full 将端口 2/3 设为全双工Switch(en able) show port mod_nu m/port_ num 查看端口配置结果例:Switch (enable) show port 2/3 查看端口 2/3 的配置结果基于CatOS的交换机输入完的命令立即存储到 NVRAM中华为交换机Quidwaysystem-view 进入系统视图Quidway in terfa
5、ce i nterface_type in terface _nu m|i nterface _n ame进入以太网端口配置模式 例:Quidway in terface ethernetO/3 进入端口 EthernetO/3 的配置模式Quidway-EthernetO/3 speed 例:Quidway-EthernetO/310| 100| auto 设置端口的速率Quidway-EthernetO/3duplex half | full例:Quidway-Ethernet0/3 duplex full| auto 设置以太网端口的全双工 /半双工属性将端口 Ethernet0/3设置
6、为全双工speed 100 将端口 EthernetO/3 速率设置为 100Mbps港湾交换机Harbourenable进入配置模式Password:*输入口令关闭自适应模式 on为打开Harbour(c on fig)# config port |all auto off例: config port 24 auto off关闭端口 24的自适应模式config port 3,7,9,18-22 auto off关闭端口 3、7、9、18-22的自适应模式Harbour(co nfig)# config port |all speed 10|100|1000例:config port 20
7、speed 100 将端口 20 速率设为 100Mbpsconfig port all speed 100 将所有端口速率设为 100Mbps设置端口速率Harbour(c on fig)# config port |all duplex full|half例:config port 20 duplex full 将端口 20设为全双工config port all duplex full 将所有端口设为全双工设置端口双工模式(half为半双工)神州数码交换机User Access Verificati onUsername: adminPassword: *CLI sessi on wit
8、h the host is ope ned. To end the CLI sessi on, en ter Exit. Con sole#Con sole# con figure输入账号、密码进入特权模式进入全局配置模式Con sole(c on fig)#Con sole(con fig-if)#Con sole(c on fig-if)#Con sole(c on fig-if)#in terface ether net 1/3no shutdow nno n egotiati onspeed-duplex 1000full | 100full | 100half | 10full |1
9、0half进入端口 Ethernet1/3 的配置模式启用该端口关闭自适应功能设置端口速率和双工模式例:Console(config-if)# speed-duplex lOOfull将端口 ethernet 1/3 设为100M全双工附录6:如何关闭交换机的生成树协议及启用端口快速CISCO交换机一、关闭生成树协议进入特权用户 进入全局配置模式 关闭某个vlan上的生树树 将vlan 1的生成树关闭 将vla n 1的生成树打开在基于IOS交换机上的配置:SwitchenableSwitch# con figure termi nalSwitch(c on fig)# no spa nnin
10、 g-tree vla n vlan-id例:Switch (config)# no spanning-tree vlan 1例:Switch (config)# spanning-tree vlan 1进入特权用户关闭所有端口的生成树 关闭某个vlan上的生树 将vlan 1的生成树关闭 将vlan 1的生成树打开在基于CatOS交换机上的配置:Switch enableSwitch (en able) set spa ntree disable allSwitch (en able) set spa ntree disable vlan例: Switch (enable) set span
11、tree disable 1例: Switch (enable) set spantree enable 1二、启用快速端口( PortFast为Cisco的私有技术)注:如果启用快速端口,就不用关闭交换机的生成树协议,快速端口只需要在接有终端的端口启用就可以,其他端口可配可不配。其他厂家交换机相同进入特权用户 进入全局配置模式 进入以太网端口配置模式在基于IOS交换机上的配置:Switch enableSwitch# con figure termi nalSwitch(c on fig)# in terface in terface module/nu mberSwitch(con fig
12、-if)# spa nnin g-tree portfast例:Switch (co nfig)# in terface faO/3 进入以太网端口 EthernetO/3 的配置模式打开端口 faO/3的快速端口在基于CatOS交换机上的配置:Switch enable进入特权用户Switch (en able) set spa ntree portfast mod_nu m/port_ num en able|disable打开或关闭某端口的快速端口例: Switch (enable) set spantree 2/3 enable打开端口 2/3的快速端口华为交换机华为交换机缺省情况下,
13、不运行生成树协议,如已开启,默认运行为 RSTP (快速生成树协议)。一、关闭生成树协议1、 关闭整个交换机的生成树Quidwaysystem-viewQuidway stp disabl e2、 关闭某个端口的生成树进入系统视图 关闭生成树协议Quidwaysystem-view Quidway in terface Quidway-EthernetO/3二、启用边缘端口Quidwaysystem-view Quidway in terface Quidway-EthernetO/3ethernetO/3stp disableEdgePort (端口快速)ethernet0/3stp edg
14、ed-port en able进入系统视图进入端口 Ethernet0/3配置模式关闭端口 E0/3的生成树进入系统视图进入端口 Ethernet0/3配置模式设定端口 E0/3为边缘端口港湾交换机港湾交换机缺省情况下,不运行生成树协议,如已开启,默认运行为 RSTP (快速生成树协议)。一、关闭生成树协议进入配置模式 输入口令 关闭生成树1、关闭整个交换机的生成树HarbourenablePassword:*Harbour(c on fig)# config spa nnin g-tree disable2、关闭某个端口的生成树Harbour enable 进入配置模式Password:*
15、输入口令Harbour(c on fig)# config spa nnin g-tree port non e-stp yes |no 设定端口的 RSTP例:config spanning-tree port 10 none-stp yes 将关闭指定端口 10 的RSTP功能、启用边缘端口 EdgePort (快速端口)Harbourenable Password:*Harbour(c on fig)# config spa nnin g-tree port edgeyes |no例:Harbour(c on fig)# config spa nnin g-tree port 8 edg
16、e yes进入配置模式输入口令|设定快速端口设定端口 8为快速端口神州数码交换机神州数码的交换机缺省情况下,不运行生成树协议。1、 关闭整个交换机的生成树User Access Verificati onUsername: adminPassword: *CLI sessi on with the host is ope ned.To end the CLI sessi on, en ter Exit.Con sole#Con sole# con figureCon sole(c on fig)# no spa nnin g-tree2、 关闭某个端口的生成树User Access Verif
17、icati onUsername: adminPassword: *CLI sessi on with the host is ope ned.To end the CLI sessi on, en ter Exit.Con sole#Con sole# con figureCon sole(c on fig)# in terface ether net 3Con sole(c on fig-ifsystem-viewQuidway igmp-snooping enableigmp-s nooping disable进入系统视图 在系统视图启用IGMP监听 为关闭IGMP监听附录7:如何设置路
18、由器、交换机的组播拓扑1 :只有二层交换机,没有路由器或三层交换功能e帆教学终端 e帆教学终端 e帆教学终端 e帆教学终端CISCO交换机CISCO缺省情况下基于IOS的交换机IGMP监听是在全局启动的, 基于Catos的交换机中Catalyst 5000 家族缺省情况下为停用,其他为启用。在基于IOS交换机上的配置SwitchenableSwitch# con figure termi nalSwitch(c on fig)# ip igmp snooping在基于CatOS交换机上的配置Switch enableSwitch (en able) set igmp en able港湾交换机进
19、入配置模式Harbourenable输入口令启用IGMP监听Password:*Harbour(con fig)# service igmp snooping en able神州数码交换机默认情况下,IGMP监听是启用状态。User Access Verificati onUsername: adminPassword: *CLI sessi on with the host is ope ned.To end the CLI sessi on, en ter Exit.Con sole#Con sole# con figureCon sole(c on fig)# ip igmp snoop
20、ing输入账号、密码进入特权模式进入全局配置模式启用IGMP监听拓扑2:有二层交换机,有三层交换机三层交换机33中庆服务器4交换机1 接中庆设备交换机2 接其他设备学校其他 服务器e帆教学终端e帆教学终端e帆教学终端e帆教学终端进入VLAN配置模式创建VLAN10创建VLAN11设VTP域名为zonekeySwitch# con figure termi nalSwitch(c on fig)# ip multicast-rout ingSwitch(c on fig)# in terface vla n 10Switch(c on fig-vla n)#Switch(c on fig-vla
21、 n)#Switch(c on fig-vla n)#ip address 192.168.10.1 255.255.255.0 no shutdow nip pim dense-mode进入vlan10的配置模式设vlan10的IP与掩码启用接口在vlan10的接口启动 PIM-DM协议Switch(c on fig-vla n)# exitSwitch(c on fig)# in terface vla n 11Switch(c on fig-vla n)# Switch(c on fig-vla n)# Switch(c on fig-vla n)# Switch(c on fig-vl
22、a n)#ip address 192.168.11.1 255.255.255.0 no shutdow nip pim dense-modeend进入vlan11的配置模式设vlan11的IP与掩码启用接口在vlan11的接口启动PIM-DM协议CISCO交换机1、三层交换机Switch enSwitch# con figure termi nal进入特权用户 进入全局配置模式Switch# vlan dataSwitch(vla n)# vlan 10 n ame zon ekeySwitch(vla n)# vlan 11 n ame otherSwitch(vla n)# vtp d
23、omai n zon ekeySwitch(vla n)# exitSwitch# con figure termi nalSwitch(co nfig)#in terface fa0/3Switch(co nfig-if)#Switch(co nfig-if)#switchport trunk en cap dot1qswitchport mode trunk进入端口 3的配置模式设端口封装为 802.1Q将端口配置为trunk模式Switch(co nfig-if)#in terface faO/4Switch(co nfig-if)#Switch(co nfig-if)#Switch(c
24、o nfig-if)#switchport trunk en cap dot1q switchport mode trunk end进入端口 4的配置模式设端口封装为 802.1Q将端口配置为trunk模式Switch# con figure termi nalSwitch(co nfig)# in terface fa0/2Switch(co nfig-if)#Switch(co nfig-if)#将端口 2定义为接入端口将端口 2加入VLAN 10中switchport mode accessswitchport access vlan 10Switch(co nfig)# in terf
25、ace faO/5Switch(co nfig-if)#Switch(co nfig-if)#switchport mode accessswitchport access vlan 11将端口 2定义为接入端口将端口 5加入VLAN 11中Switch(c on fig-if)# exitSwitch(c on fig)# ip rout ing2、交换机1Switch enSwitch# con figure termi nalSwitch(c on fig)# host name Switch-1Switch-1(config)# exitSwitch-1# vlan dataSwitc
26、h-1(vla n)# vtp domai n zon ekeySwitch-1(vla n)# vtp clie ntSwitch-1(vla n)# exit进入特权用户进入全局配置模式设VTP域名为zonekey设为客户端模式Switch-1# conf tSwitch-1(co nfig)#Switch-1(co nfig-if)#Switch-1(co nfig-if)#in terface fa0/5 switchport switchporttrunk encap dot1q mode trunkSwitch-1(co nfig)#in terface range fa 0/1S
27、witch-1(co nfig-if)#Switch-1(co nfig-if)#Switch-1(co nfig-if)#switchport mode accessswitchport access vla n 10 end设端口封装为 802.1Q将端口配置为trunk模式将端口 1-4定义为接入端口将端口 1-4加入VLAN 10中Switch# con figure termi nalSwitch(c on fig)# ip igmp snooping3、交换机2进入全局配置模式在全局启用IGMP监听Switch enSwitch# con figure termi nalSwitc
28、h(c on fig)# host name Switch-2Switch-2(config)# exit进入特权用户进入全局配置模式Switch-2# vlan dataSwitch-2(vla n)#Switch-2(vla n)#Switch-2(vla n)#vtp domain zonekeyvtp clie ntexit设VTP域名为zonekey设为客户端模式Switch-2# conf tSwitch-2(co nfig)#in terface faO/4Switch-2(co nfig-if)#switchport trunk encap dotlqSwitch-2(co n
29、fig-if)#switchport mode trunk设端口封装为 802.1Q将端口配置为trunk模式Switch-2(co nfig)#Switch-2(co nfig-if)#Switch-2(co nfig-if)#Switch-2(co nfig-if)#in terface range fa 0/1 switchport mode access switchport access vla n 11 end将端口 1定义为接入端口将端口 1加入 VLAN 11中进入全局配置模式在全局启用IGMP监听Switch-2# con figure termi nalSwitch-2(c on fig)# i
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1