电脑技术员英文自我评价.docx

1、电脑技术员英文自我评价电脑技术员英文自我评价电脑技术员英文自我评价篇一Since the company in August 2018 I was awarded the title of the technician to the present, has been four years time. In these four years, I have been in the operation department, by virtue of their own efforts and leadership to help, from a main duty officer promot

2、ed to the duty chief, and was promoted to the post of assistant. During this period, I have our first station of the system have a better understanding and awareness of some of the various types of accidents have a certain degree of independent analysis and processing capabilities, a technician to d

3、o a good job duties .My major in the school of thermal and automation control professional, but in the first station to run our work is most in need of heat, electrical and other aspects of knowledge. This is for me a new challenge, but also the need for continuous learning to improve, so that their

4、 professional skills can be fully developed. So, I got some books about these areas, targeted to our system of learning, but also ask some of the old master and professionals, ask them to show up preaching. Through their own efforts and the help of colleagues, finally work pays off, my professional

5、knowledge and professional skills have been greatly improved.But I have a lot of knowledge about the thermal aspects of our system and are particularly interested in it and have a thorough understanding of it.While at the same time learn from their own, but also assume responsibility for preaching t

6、o other operational personnel. Our company's hot water network project is the use of computer monitoring system to achieve hot water production and operation of the comprehensive monitoring of the data. Its main components include the controller, input and output modules and monitoring stations.

7、 Our company has 18 sets of SCAN3000 / S9000 distributed control system (DCS), which has the functions of hot water network operation loop control, data acquisition, data communication, centralized information management And operation display functions. It is equipped with two S9000 controllers, and

8、 another 12 single-loop controller (Honewell UDC3300), as the control loop redundancy controller and emergency hand terminal. UDC as a backup hand-held device can DCS in the event of failure, the control loop to control. With easy to operate, programmable, high stability characteristics.DCS system a

9、nd UDC can achieve between the non-disturbance switch, to ensure the stability of the system operation. S9000 controller through the DVC communication port of the DMC communication circuit and single-loop controller to achieve communication; through the MGTSTA communication port and the system monit

10、oring station communication card connected. With these control systems, usually a variety of parameters of the regulation and personnel labor will have a multiplier effect. These control systems are made up of measuring elements (temperature transmitters, pressure transmitters, differential pressure

11、 transmitters), control elements (S9000, UDC), actuators (regulators, etc.). Control flow is such that the scene collects data from a meter, the transmitter sends 4-20mA signal to the S9000 (that is often said DCS), 1-5V signal to the UDC. And then issued by the S9000 or UDC 4-20mA signal (UDC serie

12、s with 250Ω resistor, 1-5V signal to 4-20mA signal) to adjust the actuator. In this process, the instrument's power supply from the two Siemens 24V DC power supply (the two power supply each other spare), the power to the distributor, and then by the electrical distribution to a primary me

13、ter power supply (the middle of electrical distribution in order to meter repair , Will not have a short circuit, and damage the DC power supply). DCS or UDC receives the signal that is displayed on the CRT or UDC own screen. DCS or UDC control signal to the impedance converter, distributor, the iso

14、lation module or isolated relay relay to the executive control.Isolation module is through the analog signal, that is, continuous control signal 4-20mA, such as the valve opening, level control; and isolation relay is the switch signal to the DCS, such as temperature switches, pressure switches and

15、pumps Start, stop state, etc. (plus isolation module, isolation relay is to isolate strong signals, so as not to S9000 in the loop control card burned).During the shift, as a monitor, I assume the responsibility of the entire hot water network security and economic operation, the spirit of a high de

16、gree of concentration during work, leading the team members carefully adjust the parameters, careful analysis of the data, sum up the law, Found that equipment defects and risks, to prevent the expansion of the accident. Not only to ensure the safe operation of the hot water network, but also to the economic operation. In some parameters and equipment anomalies, can do a timely analysis, find out the reasons and report, with a certain degree of ind