compaq外观检验标准.docx

1、compaq外观检验标准APPLICATION 应用REVISION 修改NEXT ASSYUSED ONECN NO.LTRDESCRIPTION 内容DATE 日期APPROVED 审核1005666587JCHANGES PER ECN02/19/91C. BUCKNERB8601KCHANGES PER ECN01/26/96V. BLAKEN4943LINACTIVATE 001/RELEASE 000ORIGINAL APPROVAL SIGNATURES ARE SHOWN ON REVISION “AX” OR “A” RELEASE 原审核签名见于修订本 “AX”或” “A”

2、版本PROPRIETARY NOTE所有权申明THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO COMPAQ COMPUTER CORPORATION AND该文件所含信息为机密文件, 且所有权归属于COMPAQ 计算机公司, 在无COMPAQ 公司明确的尽面认可的条件下, SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR 不可以任何目的翻版或转移到其它任何文件, 或是透露给他

3、人或使用, ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF COMPAQ COMPUTER CORPORATION.际了应用于获取目的之外.UNLESS OTHE RWISE SPECIFIED, DIMENSIONS ARE IN INCHES MILLIMETERS. 悇非另有规定, 尺寸 用英寸(毫米). TOLERANCES ARE:规定为:APPROVALS审核DATE日期FRACTION分比DECIMALS小数ANGLES角度DRAWNR.

4、BLACKMAN07/29/86 1/32.XX .020.51CHECKEDM. MCCULLOUGH07/29/86.XXX .010 0.25COG ENGRK. TRAPANI08/18/86SPECIFICATION, COSMETIC REQUIREMENTS,ENGF. CASSON08/22/86PLASTICTOOLING规格, 外观要求, 塑料DIMENSION DESIGNATORSMFGC. WINDER08/20/86DENOTED BY “”.QAN. CAHAN08/22/86SIZECLASS CODEDRAWING NO.REV尺度指定者用 “” 表示.MTL

5、 CTRLK. BRAUN08/21/86A0436106413LDO NOT SCALE DRAWING非按原物比例画AGENCY代理I. GOMEZ08/20/86SUPPLEMENTS:EFSHEET 1OF1TABLE OF CONTENTS 目录1. SCOPE 范围 2. APPLICABLE DOCUMENTS 适用文件 3. INSPECTION 检测 3.1 VISUAL INSPECTION 目测 3.1.1 Lighting 灯光 3.1.2 Position 位置 3.2 POSSIBLE DEFECT 可能存在之缺点 4. DEFINITION OF CLASSES

6、类别定义 4.1 CLASS I 类别1 4.2 CLASS II 类别II 4.3 CLASS II I类别III 4.4 CLASS IV 类别IV 5. ALL CLASSES 所有类别 5.1 CLEANLINESS 清洁 5.2 FLASH 毛边 5.3 MISMATCH 错配 5.4 SONIC WELDS 快速焊接 5.5 GENERAL 常规 6. CLASS I 类别I 6.1 SCRATCHES/ABRASIONS 刮伤 / 磨损 6.2 SPLAY 轻微裉色 6.3 CONTAMINATION 污染 6.4 SINKS 凹槽 6.5 BLUSH 变色 6.6 KNIT L

7、INES 接合线 6.7 COSMETIC PAINT 外观漆 6.7.1 Adhesion 附着力 6.7.2 Inclusions 杂物 6.7.3 Pin Holes 针孔 6.7.4 Scratches 刮伤 6.7.5 Painted Groove 着色凹槽 6.7.6 Unpainted Groove 不着色凹槽 TABLE OF CONTENTS目录7. CLASS II 类别II 7.1 SCRATCHES/ABRASIONS 刮伤 / 磨损 7.1.1 Textured Surfaces 有纹路表面 7.1.2 Non-Textured Surfaces 无纹路表面 7.2

8、SPLAY 轻微裉色 7.3 CONTAMINATION 污染 7.4 SINKS 凹槽 7.5 BLUSH 变色 7.6 KNIT LINES 接合线 7.7 COSMETIC PAINT 外观漆 7.7.1 Adhesion 附着力 7.7.2 Inclusions 杂物 7.7.3 Pin Holes 针孔 7.7.4 Scratches 刮伤 7.7.5 Painted Groove 着色凹槽 7.7.6 Unpainted Groove 不着色凹槽 7.8 SPRUE HOLES 直浇口 8. CLASS III 类别III 8.1 SCRATCHES/ABRASIONS 刮伤 8.

9、2 SPLAY 轻微裉色 8.3 CONTAMINATION 污染 8.4 SINKS 凹槽 8.5 BLUSH 变色 8.6 KNIT LINES 接合线 8.7 SPRUE HOLES 直浇口 8.8 EMI COATED SURFACES EMI 保护面 8.8.1 Electrical Requirements 电性要求 8.8.2 Adhesion 附着力 8.8.3 Color Variations 颜色变异 8.8.4 Coating Build-Up 内建保护层 8.8.5 Dry Spray 干燥的喷漆物 8.8.6 Inclusions 杂物 8.8.7 Pin Holes

10、 针孔 8.8.8 Overspray 超范围喷漆 8.8.9 Underspray 不足喷漆 8.8.10 Scratches 刮伤 8.8.11 Corrosion and Fingerprints 腐蚀 TABLE OF CONTENTS目录9. CLASS IV 类别IV 9.1 SCRATCHES/ABRASIONS 刮伤 / 磨损 9.2 SPLAY 轻微裉色 9.3 CONTAMINATION 污染 9.4 SINKS 凹槽 9.5 BLUSH 变色 9.6 KNIT LINES 接合线 9.7 EMI COATED SURFACES EMI 保护层 9.7.1 Electric

11、al Requirements 电性要求 9.7.2 Adhesion 附着力 9.7.3 Color Variations 颜色变异 9.7.4 Coating Build-Up 内建保护层 9.7.5 Dry Coating 干膜 9.7.6 Inclusions 杂物 9.7.7 Pin Holes 针孔 9.7.8 Over-Coating 超范围喷漆 9.7.9 Under-Coating 不足喷漆 9.7.10 Scratches 刮伤 9.7.11 Corrosion and Fingerprints 腐蚀 10. GLOSSARY OF TERMS 术诏表 LIST OF FI

12、GURESFIGURE 1 POSITIONING 图1 位置 1. SCOPE 范围This specification defines the cosmetic requirements for PLASTIC PARTS and ASSEMBLIES for 该规格详细说明了Compaq 计算机公司对塑料部件和装置的外观要求Compaq Computer Corporation. The cosmetic requirements shall be divided into four classes in 该外观要求根据部位可分为4 类.accordance to area locati

13、on.2. APPLICABLE DOCUMENTS 适用文件Where this specification refers to another document, that document is of the issue in effect on the date of 当该规格引用其它文件时, 则此文件发行自受邀命令或要求提议之日起生效invitation to bid or request for proposal. Referenced documents apply to the extent specified herein.引用的文件适用于此处规定的范围3. INSPECTI

14、ON 检测3.1 VISUAL INSPECTION 目测Visual inspection shall be conducted as follows: 目测执行如下3.1.1 Lighting 灯光100 20 foot-candles cool white fluorescent illumination.100 20Foot-candle 这种型号的冷白荧光灯照明.3.1.2 Position 位置Place the assembly 18.000 to 24.000 (arms length) in front of person inspecting. The part 将装置置于

15、检测员前方18.000 24.000 (臂长).should be held in two (2) positions; parallel to the light source and 30 degrees from the light 部件需置于两种位置: 与光源平行和距光源30度. 见图1.source. See Figure 1.3.2 POSSIBLE DEFECT 可能存在之缺点If a possible defect is found in both the above mentioned positions (refer to Figure 1), refer to the 若

16、在上述两种位置情况下都发现有可能存在之缺点 (指图1), appropriate class for rejection criteria. Possible defects found outside the viewing parameters shall 参考合适类别的拒收标准. 检视限量之外的可能存在缺点可被忽略.be considered not visible.4. DEFINITION OF CLASSES 类别定义4.1 CLASS I 类别IClass I areas shall be defined as areas in continuous view of the op

17、erator.类别I 部位是指操作员可持续观看到的部位.4.2 CLASS II 类别IIClass II areas shall be defined as areas occasionally in view of the operator.类别II 部位是指操作员可偶尔观看到的部位.4.3 CLASS III 类别IIIClass III areas shall be defined as areas seldom seen by the operator.类别III 部位是指操作员很少观看到的部位.4.4 CLASS IV 类别IVClass IV areas shall be def

18、ined as areas never seen by the operator.类别IV 部位是指操作员从未观看到的部位.5. ALL CLASSES 所有类别5.1 CLEANLINESS 清洁Parts shall be free of dirt, grime, grease, and other contaminants. Dust caused by shipping material 部件需无污垢, 污点, 油脂 和其它污渍. is acceptable if it can be blown off with air or wiped off.由运输材料引起的灰尘若能被吹去或擦去,

19、则可允收.5.2 FLASH 毛边The height of any flash greater than .01 is not acceptable. Where flash has been trimmed, the cut 任何高度大于0.01的毛边不可允收. 修理过毛边的地方, 切痕不可除去任何纹路.marks shall not remove any texture. Any trimmed surface shall be smooth without jagged edges.任何修理过的表面需光滑无锯齿边缘.5.3 MISMATCH 错配Mismatch greater tha

20、n .01 per side is not acceptable.错配每边大于0.01不可允收.5.4 SONIC WELDS 快速焊接The gap between sonic welded parts greater than .01 is not acceptable.快速焊接部件之间间隙大于0.01 不可允收.5.5 GENERAL 常规Short shots, burns, cracks, nicks, voids, and crazing are not acceptable.注入不足, 灼伤, 破裂, 刻痕, 空点和裂纹 不可允收.6. CLASS I 类别I6.1 SCRATC

21、HES/ABRASIONS 刮伤 / 磨损Scratches or abrasions which remove texture are not acceptable.会除去纹路的刮伤或磨损不可允收.6.2 SPLAY 轻微裉色Splay is not acceptable.轻微裉色不可允收.6.3 CONTAMINATION 污染Molded-in contamination greater than .025 in diameter is not acceptable. Any particle of 嵌入污染物直径大于0.25不可允收.contamination less than .0

22、1 or less in diameter and with a minimum distance of .50 from any other 任何直径小于0.01或更小, 且距任何 其它粒子最小距离为0.50的污染粒子可被忽略.particle shall be considered not visible. The minimum distance between any two (2) particles of 任意两污染粒子之间的最小距离需是2.00英寸.contamination shall be 2.00 inches.6.4 SINKS 凹槽Sinks greater than

23、.005, when measured with a dial indicator with a .040 diameter tip, are not acceptable.当用一带有直径为0.040尖端的千分表(刻度盘显示器) 测量, 凹槽大于0.005不允收.6.5 BLUSH 变色Blush in this area is not acceptable without prior written approval from Compaq Computer Corporation.无事先Compaq 计算机公司的尽面认可, 该部位变色不允收.6.6 KNIT LINES 接合线Visibl

24、e knit lines are not acceptable in this area without prior written approval from Compaq Computer Corporation.无事先Compaq 计算机公司的尽面认可, 该部位可视接合线不可允收.6.7 COSMETIC PAINT 外观漆All cosmetic painted surfaces shall meet the color requirements as defined by Compaq所有包装喷漆的表面需符合Compaq 计算机公司规定的颜色要求.Computer Corporati

25、on. All painted surfaces shall be uniform in gloss and free of streaks, runs, flakes, bubbles, or loss of texture caused by paint build-up.所有喷漆表面的光泽面需一致, 且无由内建漆引起的条纹, 熔化, 剥落, 空泡, 或纹路遗失.6.7.1 Adhesion 附着力Cosmetic paint shall not separate from the base material when subjected to adhesion tests 在Compaq

26、 计算机公司规定的粘合测试当中, 外观漆需不会脱离底料.specified by Compaq Computer Corporation. Paint shall be cured completely so that it cannot 喷漆需彻底以使其不会被干布或手指擦去.be rubbed off by a dry cloth or the fingers. If any paint transfers to a dry cloth or the fingers, 若任何漆被擦到了干布或手指上, 则此部位不允收.that part is not acceptable.6.7.2 Incl

27、usions 杂物Any inclusion greater than .04 in diameter is not acceptable. There shall be no more than four 任何直径大于0.04的杂物不可允收.(4) inclusions per surface. The minimum distance between any two (2) inclusions shall be 2.00 每面需不超过4 处杂物. 任意两处杂物之间的最小距离需是2.00英寸.inches.6.7.3 Pin Holes 针孔Pin holes greater than .

28、01 in diameter are not acceptable. There shall be no more than four (4) 直径大于0.01的针孔不可允收. 每面不可超过4处针孔.pin holes per surface. The minimum distance between any two (2) pin holes shall be 2.00 inches.任意两处针孔之间的最小距离需是2.00英寸.6.7.4 Scratches 刮伤Scratches that remove paint are not acceptable.会磨去油漆的刮伤不允收.6.7.5

29、Painted Groove 着色凹槽Where paint occurs on the bottom of the groove, there shall be uniform coverage on the bottom 在凹槽底部要着色的地方, 凹槽底部和内侧需复盖一致.and inside wall of the groove. The outside wall of the groove may contain underspray as long 凹槽外侧可包含不足喷漆, 只要边线波动每英寸不超过0.02.as the mask line does not fluctuate mo

30、re than .02 per inch.6.7.6 Unpainted Groove 不着色凹槽Where paint does not occur on the bottom of the groove, there shall be uniform coverage up to 在凹槽底部不着色的地方, 统一复盖直到凹槽.the groove. The inside wall of the groove may contain overspray as long as the paint line does 凹槽内侧可包含过量喷漆, 只要漆线波动每英寸不超过0.02.not fluctuate more than .02 per inc