Aruba Site Survay Example 参考格式.docx

1、Aruba Site Survay Example 参考格式SBC Wireless Site Survey Coverage Assessment ReportDuty Free AmericasLaredo, TXPrepared By:Rob Stewart Date:10-1-04Table of ContentsOVERVIEW 3Specific Tasks Performed During the Wireless Site Survey Coverage Assessment: 3Disclaimer 4Contact Information: 5Areas of Propos

2、ed RF Coverage: 6Specific Site Description: 6Site Survey Test Parameters 6System Configuration Summary: 7Equipment List: 7Special Considerations and Assumptions: 7Network Information: 8System Component Locations: 10Power, Cabling and Networking Requirements: 59Facility Drawings: 60Appendix A - Cable

3、 and Mounting Guidelines: 71Appendix B Power over Ethernet Diagram 72Appendix C - Network Cabling Best Practices Guidelines for Cat 5/5e UTP cable 73Appendix D - Network Design Best Practices Guidelines 76 OVERVIEWOn 9/29/04, a Wireless Site Survey Coverage Assessment was conducted for Duty Free Ame

4、ricas in Laredo, TX. This Wireless Site Survey Coverage Assessment was conducted to determine the number of access points, antenna types and associated installation hardware required, and their respective locations in the facility to meet the coverage requirements as stated in the statement of work.

5、 This report is based upon the specific findings of the Wireless Site Survey Coverage Assessment, as well as coverage requirement facts as known at the time and as provided in the Scope of Work. All findings will apply to Duty Free Americas Site Coverage Assessment unless Duty Free Americas: Physica

6、lly changes or remodels the site with new or rearranged structural items Changes the stacking or storage of certain items that affects RF propagation Installs additional equipment emitting electromagnetic radiation fields affecting RF propagationThis Wireless Site Survey Coverage Assessment Report c

7、ontains all required specifications to facilitate the installation and implementation of the Wireless 802.11 Communications System and achieve the desired coverage. This report is to be used by the System Architect as a tool to incorporate into their design the number of access points, antenna types

8、 required and their respective locations in the facility. The Network Cable Co. and the RF Installation Team can also use this report to install all the required components as identified by model or specification number, location, and termination points. Specific Tasks Performed During the Wireless

9、Site Survey Coverage Assessment: Perform walk through of facility to verify coverage area as defined in the Scope of Work. Determined the number of access points, antenna types, mounting requirements and cabling requirements (data & power) required to provide the desired wireless coverage and their

10、respective locations in the facility. Determine the proper RF channel assignments and RF power settings for each access point. Perform a best effort identification of any detected potential sources of RF interference that could impact the wireless network performance. Survey the existing network con

11、nections and equipment to confirm that minimal acceptable hardware and software requirements are met. Evaluation of space and electrical requirements. Physically tag all access point and antenna locations. Provide a completed Wireless Site Survey Coverage Assessment Report.DisclaimerThe Wireless Sit

12、e Survey Coverage Assessment is not a System Network Design or Cable Plant Extension. This service does not include network utilization testing, wireless security audit or network design. The access points being proposed use radio(s) that is unlicensed. SBC cannot guarantee there will never be other

13、 sources of interference or radio frequencies in the areas within this proposed wireless system. This document can be used along will the enclosed Best Practice Wireless Design Guidelines to formulate a System Design. The SBC representative(s) responsible for the contents of this document are:NameTe

14、lephone NumberPrimary Customer Representative(s) supplying information used in this document are:NameTelephone NumberAllen Rodriquez954-986-7656 Contact Information:SBC Account Management Information Account Manager NameJeff KetteringCompany NameStreet Address2500 N. Andrews Ave. Ext.City, State Zip

15、Pompano, FL 33064Telephone(954) 317-0754EmailJk8535SBC Project Management InformationProject Manager: Project Manager Phone Number:Project Manager E-mail Address:Customer InformationCustomer Name:Duty Free AmericasStreet Address:110 InternationalCity, State, ZipLaredo, TX. 78045Primary Customer Cont

16、act:Allen RodriguezPrimary Contact Phone Number:954-986-7656Site Contact:Site Phone Number:Areas of Proposed RF Coverage:Prior to conducting the RF Site Survey a discussion and brief tour were conducted for site orientation and to determine which areas of the facility would require RF network operat

17、ion. Duty Free Americas representative Allen Rodriguez coordinated the orientation walk-through. Specific Site Description:Type of Facility Surveyed:Warehouse ComplexTotal Square Footage Covered Approximately 200,000 sq ft totalDescription of Coverage Areas:Large/Small warehouse, Motor pool, Executi

18、ve Offices, and outdoor areas between each of these buildings.Total Number of Buildings:FourNumber of Floors in Tallest Building:TwoFloor, Walls and Ceiling Material:Concrete, Drywall, Corrugated Steel, Red iron.Ceiling Height:9ft 30ft.Approximate Inventory Level:85%Existing Wired Network Type:Cat5E

19、xisting RF Networks:NoneSite Survey Test ParametersAccess Point Type:Cisco 1200gClient Device:Cisco 350gDiagnostic Program:Aironet Client UtilityPing Packet Size: 1024Surveyed Data Rate:36mbChannels Utilized1,6,11System Configuration Summary:Total Number of Access Points23Total Number of Bridge Unit

20、s0Number of Outside Antennas for APs10Number of Outside Antennas for bridge2Number of Inside Antennas22Number of Antennas Using Diversity22Power Option: A/C or PoEPoEAre There Lift Requirements? If So, Then What Type of Lift is Required?Yes, a scissor lift that reaches 30 ft. will be required to com

21、plete this install.Equipment List: QtyDescriptionPart Number18Aruba AP-70 A/B/G access Point AP-705Aruba AP-80M outdoor Access PointAp-80M18PoE Injector (for AP in Motor Pool)PD-3001-AC226.0 dBi Aruba Indoor/Omni antennaAP-ANT-2106.0 dBi Aruba Outdoor/Omni antennaAP-ANT-8012Lightning ArrestorsAP-LAR

22、117AP-70 Mounting Kit AP-70-MNT2GBIC-T11Hyperlink Pre-Drilled Fiberglass NEMA Enclosure NB141207-40F466 Patch Cables2Aruba-2400 controllers2Security bundle licensesSpecial Considerations and Assumptions:Outdoor APs and Bridge Units will NOT require an antenna extension.The customer currently has Cis

23、co 3550 series switches that provide PoE, they may or may not use these for the install, if not they will need to order PoE injectors for each Access Point and Bridge unit.Network Information:The following Network Components and their locations were identified:MDF / IDF LocationsSwitch Type (Mfg & M

24、odel #)Number of Switch Ports AvailableNumber of Patch Panel Ports AvailableAdditional A/C Outlets NeededMDF-Export OfficeCisco 2970Cisco 2900Cisco 3550Cisco 3550Cisco 3550209122263 openIDF2-Executive OfficesCisco 3550Cisco 35501017242 openIDF3-Small WarehouseCisco 35501502 openIDF4-Large WarehouseC

25、isco 3550Cisco 3550Intel 210T332422 openNOT INSTALLEDIDF5-Motor PoolN/AN/AN/A2 openAdditional Network CommentsIDF5 needs to be installed. This could be a 4port hub located in the Motor Pool to connect the Non-Root Bridge to the interior Access Point #17.The site has 3550 routers on site, but the Lar

26、ge Warehouse would need and additional one to make room for all of the APs. If the customer decides to use PoE injectors then they would need to be added to the parts list. MDF IDF2 IDF3 IDF4IDF5-Possible LocationSystem Component Locations:Access Point #1:Equipment Type:ARUBA AP-70Antenna Type:Integ

27、rated Omni-directional DiversityLocationImport Department/Over Jose CoronadoMDF / IDF LocationIDF2Distance to MDF / IDF50Data Cable Drop RequiredYesA/C Power Drop RequiredNoNEMA Enclosure RequiredNoDrop Ceiling Enclosure Required (optional)NOMounting Height9 ft.Mounted ToDrop CeilingLocation Marked

28、By4 - ” Colored DotsDiversity UtilizedYesRF Channel SettingAUTOAP Power SettingAUTOAP Mounting Instructions:AP can be installed directly on top of drop ceiling. Using an Aruba mounting kit will allow for drop-ceiling “T-Bar” exposed mounting.Antenna Mounting Instructions:Antenna is integrated and sh

29、ould be in a vertical position.Data and Power:Data and Power will be fed via the new Cat 5e cable run.Access Point #1 PicturesAccess Point #2:Equipment Type:ARUBA AP-70Antenna Type:Integrated Omni-directional DiversityLocationTraffic/Near Teresa EnriquezMDF / IDF LocationIDF2Distance to MDF / IDF70D

30、ata Cable Drop RequiredYesA/C Power Drop RequiredNoNEMA Enclosure RequiredNoDrop Ceiling Enclosure Required (optional)NOMounting Height9 ft.Mounted ToDrop CeilingLocation Marked By4 - ” Colored DotsDiversity UtilizedYesRF Channel SettingAUTOAP Power SettingAUTOAP Mounting Instructions:AP can be installed directly on top of drop ceiling. Using an Aruba mounting kit will allow for drop-ceiling “T-Bar” exposed mo