捷豹TP560x AT10x驱动安装说明.docx

1、捷豹TP560x AT10x驱动安装说明TP560i56Kbps Data/Fax/Voice Modem Chip SetPCI Bus InterfaceUsers ManualAT Command SetIntroductionThis is a high performance ITU-V.90 56Kbps modem; Computer can make connection with remote terminal, send a fax and be a telephone answer machine by this modem. In data mode, this mod

2、em provides ITU V.90, V.34, V.32bis, V.32, V.22bis, V.22, V.23, V.21 and bell212A/103 connection protocol speed from 300bps to 56Kbps. This modem also provides MNP class 5 and V.42bis compression method during data transmission. In Fax mode, this modem can send and receive Fax in 14.4kbps that is co

3、mpatible to ITU-V.17 standard, Fax function is follow ITU Group 3 fax standard. More detail information, please refer to users manual of communication software and AT command set.Packing information1. Users manual2. Communication Software3. RJ-11 telephone cable4. 3.5 inch Disk (Win95/98 Driver & IN

4、F files)5. Ear Phone and Mic Phone Hardware InstallationStarting the Installation1. Turn off your computer and unplug its power cable.2. Unplug your computer before removing the top or you could hurt yourself and damage the equipment.3. Remove the computer cover according to the directions in the co

5、mputer manual.4. Choose a PCI slot.5. Remove the rear panel metal bracket that corresponds to the slot you plan to use.6. Hold the modem over the expansion slot. Place the modem into the slot and push it down so that it is firmly seated.7. Replace the computer cover.8. Plug one end of the supplied p

6、hone cable into line jack on the modem metal bracket, the other into a modular phone wall jack.9. You can connect a phone to your modem by plugging the phone modular plug into the modems phone jack. With this arrangement you can use your telephone normally when the modem isnt being used.11. Turn on

7、the computer.Windows 95/98 installationIf your computer uses Windows 95, plug and play? Both Windows 95 and your computer support plug & Play. Plug and Play lets you plug in a device such as your modem and then use it immediately.To finish your Windows 95 installation, follow these steps 1. Turn on

8、your computer if it not already on. If the New Hardware Found dialog box appears, you need to install a modem driver file, as explained in steps 2. If the New Hardware Found box does NOT appear, Windows 95 already has a driver for your Modem. Skip ahead to step 6.2. Insert the Disk that is provided

9、by hardware manufacture into floppy drive A (or B).3. Chose Driver source is in floppy drive A (or B).4. Click on OK. Windows 95 automatically copies the modem driver to your hard disk and uses it.5. Eject the disk and store it in a safe place.6. Your modem is now installed. Now install the fax and

10、data software that came with your modem, as explained in your modem manual.AT Commands ReferenceAT commands are issued to DTE to control the modems operation. AT commands can only be entered while the modem is in command mode. Except for the A/ command and the + escape command, all commands must be

11、prefixed with the attention code AT. For instance, the “A” command (below) would be entered as: ATA. Without the AT prefix, the command line cannot be executed. For example: The format for entering AT commands is “ATXn” where X is the AT command, and n is the specific value for that command.More tha

12、n one command can be placed on a single line and (if desired) separated with spaces for readability. Once the carriage return (Enter) key is pressed, the command line is executed. A line with no carriage return is ignored. Any command issued is acknowledged with a response in either text or numeric

13、values known as result codes. In the following, all commands, command-values and result code recognized by the modem are shown; any entries other than those shown cause the ERROR result code. The modem accepts either upper or lower case characters in the command line and ignores any spaces within or

14、 between commands. Typing errors can be corrected with the Backspace key. Exceptions are noted in the description of specific commands.+AT Escape SequenceThe escape sequence allows the modem to exit data mode and enter online command mode. While in online command mode, you may communicate directly t

15、o your modem using AT commands. You may return to data mode by issuing the ATO command. Section 1. Data Mode CommandA/ Executes Last Command When modem receives this command, modem executes the last command string entered. Do not conclude it by pressing “Enter”.A Answer Command This command instruct

16、s the modem to go off-hook and answer an incoming call.Bn Communication Standard SettingThis command determines ITU-T vs. Bell standard.B0 Selects ITU-T V.22 mode when the modem is at 1200 bits/s.B1 Selects Bell 212A when the modem is at 1200 bits/s (default).Result Codes: OK : n = 0, 1ERROR : OtherwiseDn DialThis command instructs the mod