1、Driver Error & 驱动器错误 &Cache Memory Bad, Do not Enable Cache & 高速缓存Cache损坏,不能使用 &Error: Unable to control A20 line & 错误提示:不能使用A20地址控制线 &Memory write/Read failure & 内存读写失败 &Memory allocation error & 内存定位错误 &CMOS Battery state Low & CMOS没电了 &Keyboard interface error & 键盘接口错误 &Hard disk drive failure &
2、加载硬盘失败 &Hard disk not present & 硬盘不存在 &Floppy disk(s) fail (40) & 软盘驱动器加载失败,一般是数据线插反,电源线没有插接,CMOS内部软驱设置错误 &CMOS checksum error-efaults loaded. & CMOS校验错误,装入缺省(默认)设置 二、BIOS刷新失败后,Bootblock启动时出现的提示信息Detecting floppy drive A media. & 检测软驱A的格式 &Drive media is : 1.44Mb1.2Mb 720Kb 360K & 驱动器格式是1.44Mb、12Mb、
3、720kb、360kb的一种 &DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER & 磁盘引导失败,插入系统盘后按任意键继续 三、MBR主引导区提示信息Invalid partition table & 无效的分区表 &Error loading operating sy stem & 不能装入引导系统 &Missing operating system & 系统引导文件丢失 说明:如果在计算机启动过程中,在硬件配置清单下方(也就时在平时正常启动时出现Starting Windows 98的地方)出现不可识别字符,此时可判断硬盘分区表损
4、坏。如果你的硬盘上有重要资料,这时你不要轻易进行分区,可找专业的数据恢复公司。四、DOS活动分区中的提示信息Invalid system disk & 无效的系统盘 &Disk I/O error, Replace the disk and press any key. & 磁盘I/O错误,替换磁盘后按任意键(当C盘系统文件丢失或被破坏时出现该提示信息。这时可能SYS C:为修复系统文件) &Invalid Media Type reaching Drive C: & 无效的盘媒体格式说明,也就是C盘没有格式化或者是其他操作系统的磁盘格式如NTFS &Invalid Boot Diskette
5、 Boot Failure & 无效的启动盘,启动失败 五、IO.SYS中的提示信息 说明 &Insert diskette for drive and press any key when ready & 插入磁盘到驱动器中后按任意键 &Your program caused a divide overflow errorIf the problem persists, contact your program vendor & 你的程序导致溢出错误。如果该问题还存在,请联系你的程序供应商 &Windows has disabled direct disk access to protect
6、 your long filenames Windows & 不能直接访问受保护的长文件名 &The system has been halted. Press Ctrl+Alt+Del to restart your computer & 系统挂起,按Ctrl+Alt+Del重新启动你的计算机 &You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windo
7、ws and then restart & 你启动的MS-DOS版本与Windows版本不兼容,请插入与Windows版本匹配的系统盘后再重启 &This version of Windows requires a 386 or better processor 该Windows版本需要386以后的CPU支持 &A20 hardware error. Contact technical support to identify the problem & 地址线A20错误。联系技术支持来识别该问题 &Starting Windows 98. & 正在启动Windows 98 &Windows 9
8、8 is now starting your MS-DOS-based program & Windows 98正在启动基于MS-DOS的程序 &Windows 98 is now restarting. & Windows 98正在重新启动 &Press Esc now to cancel MS-DOS mode and restart Windows 98. & 按Esc退出MS-DOS 模式,重新启动Windows 98 &There is an unrecognized command in your CONFIG.SYS file & 在你的CONFIG.SYS文件中有不可识别的命令
9、 &The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列错误命令 &The sector size specified in this file is too large: 该文件中指定的扇区太大 &The following file is missing or corrupted: WIN.COM COMMAND.COM & 下列文件丢失或被破坏:WIN.COM和COMMAND.COM &There is an invalid country code or code page in you
10、r CONFIG.SYS file & 在你的CONFIG.SYS里有一个无效的国家代码 &There is an error in the COUNTRY command in your CONFIG.SYS file & 在你的CONFIG.SYS里有一个错误的设置国家命令 &There is not enough memory for the COUNTRY.SYS file & 没有足够的内存来加载COUNTRY.SYS文件 &Remove some drivers from your CONFIG.SYS file, and then try again & 请从CONFIG.SYS
11、文件中删除部分驱动程序,然后再试 &Remove some drivers, and then try again & 去除一些驱动程序,然后再试。这里的驱动程序是指在CONFIG.SYS中使用device或devicehigh命令加载的程序文件 &Remove some disk drivers from your CONFIG.SYS file, and then try again & 从你的(CONFIG.SYS)移去部分程序,然后再试 &The configuration specified in your CONFIG.SYS file is too large for memor
12、y & 调整你的CONFIG.SYS文件以获得足够大的内存 &You have too many block devices specified in your CONFIG.SYS file & 调整你的CONFIG.SYS文件以获得block devices &The STACKS setting(s) in your CONFIG.SYS file are incorrect & 在你的CONFIG.SYS中堆栈设置不正确 &Default stack settings will be used instead & 缺省的堆栈设置将被替代使用 &There is an error in
13、your CONFIG.SYS file on line XX & 在你的CONFIG.SYS里XX行错误 &Warning: Logical drives past Z exist and will be ignored &警告:逻辑驱动器Z已经存在,将被忽略 &Type the name of the Command Interpreter (e.g., C:WINDOWSCOMMAND.COM) Press any key to continue &请输入命令解释器的文件名(如:C:WIN DOWSCOMMAND.COM)后,按任意键继续 &Windows is bypassing yo
14、ur startup files Minimal network support will be loaded if available Windows &正在跳过你的启动文件。如果网络可用,最小网络支持将被加载 &Windows is starting the command prompt only &Windows正在启动命令字符模式 &Windows will prompt you to confirm each startup command &Windows将提示你确认每一个启动命令 &The compression driver cannot be set up correctly
15、 &压缩驱动程序不能被正确加载 &Get a version from your vendor that is compatible with this version of Windows &从你的供应商那里获得一个与Windows版本相兼容的版本 &Process the system registry &运行系统注册表 &Create a startup log file (BOOTLOG.TXT) &创建启动日志BOOTLOG.TXT文件 &Process your startup device drivers (CONFIG.SYS) & 运行CONFIG.SYS文件中的设备驱动 &
16、Process your startup command file (AUTOEXEC.BAT) & 运行AUTOEXEC.BAT中的启动命令 &Load the Windows graphical user interface &装入WINDOWS图形用户界面(GDI) & Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG &Windows检测到一个注册表或配置错误选择DOS操作模式,运行SCANREG & Windows has detected
17、 a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem &Windows检测到一个访问压缩驱动器错误,选择安全模式下的MS-DOS,来帮助你识别这个问题 & Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers &Windows在刚才尝试后不能够完成加载,选
18、择安全模式,用最小驱动启动你的电脑 & Windows multi-boot may not function correctly Check for system files in your root directory with conflicting extensions &Windows不能够正确完成多系统启动,在你的ROOT目录里检查不一致的系统文件 & the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly &系
19、统管理器运行失败,一些实模式驱动可能没有正确初始化 &The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS里BUFFER设置太大。默认的BUFFER缓冲器设置将被使用 &A memory allocation error occurred during startup<BR& p>Restart your computer and select Interactive Start to ident
20、ify the problem &在启动过程中内存分配发生错误,请重新启动你的计算机然后选用交互式方式启动来确定故障原因 & the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead &高端内存不可用,低端内存将被代替使用 &There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again &对Windows来
21、说没有足够的内存,请从CONFIG.SYS文件中移去部分加载的程序,然后再试着启动你的读入计算机 &Your previous MS-DOS files were not found. &旧的MS-DOS文件没有找到,这常见于使用双启动的系统,另一个系统是DOS6 &Your previous MS-DOS version is not supported. MS-DOS startup failed & 旧的MS-DOS版本不支持。MS-DOS启动失败 &Now loading your previous version of MS-DOS, please wait & 现在正在加载旧的MS
22、-DOS版本,请等待 &Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS & 文件中无效的设置选项,系统堆栈溢出,系统挂起 &Change the STACKS setting in your CONFIG.SYS file, and then try again & 请改变CONFIG.SYS文件中的STACK设置,然后再试 &Stack overflow &堆栈溢出 &Integer divide by 0 整数被0除
23、 &Not enough space for environment 没有足够的空间 &Run-time error & 运行错误 &Floating-point support not loaded 浮点运算支持没有装入 &Null pointer assignment 无效的断点分配 六、COMMAND中的提示信息 堆栈溢出 &Integer divide by 0 & 分母是0 &Not enough space for environment & 磁盘没有足够的空间 & 时钟错误 &No fixed disks present & 没有硬盘存在 &Insufficient memory
24、 & 内存不足 &Invalid drive specification & 无效的驱动器名 &Invalid characters in volume label & 无效的盘符 &Invalid Volume ID & 无效的卷标ID号 &No target drive specified & 目标驱动器没有定义 &missing operating system & 系统文件丢失 &Non system Disk or Disk Error & 不是系统盘或磁盘错误 &Replace Disk and Press Anykey To Reboot & 替换磁盘,按任意键重新启动 七、SY
25、S传送系统文件时的提示信息Cannot find System Files & 不能找到系统文件 &System transferred & 系统传送完毕 &Disk unsuitable for system disk & 目标磁盘不适合做系统盘 八、FORMAT中的提示信息Unable to write BOOT. & 不能写引导扇区 &Invalid media type & 无效的磁盘类型 &Parameters not supported & 参数不支持 &Cannot format a network drive & 不能格式化网络驱动器 &Invalid media or Track 0 bad - disk unusable & 无效的磁盘或磁道损坏,磁盘不可用 &Format terminated & 格式化终止 &
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1