模具英语100句 修改OK版Word文档格式.docx

1、Theres an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK?6 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？We will make the lifter and （inner） slider in this position, will that be a problem?7 你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？The 2

2、D and 3D drawings you provided are not the same, could you advise which one is correct?8 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。There is no draft angle in the 3D model, some areas are too thick, and some are too thin. Can we modify them by ourselves? We will send you the upd

3、ated drawing for approval.9 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？According to the shrinkage rate .005”, the mold has been done in the right dimension, but the part falls short to your part print（the actual dimensions are out of tolerances）, are you sure the shrinkage i

4、s right?10 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？This position is too small and will cause thin steel, can we widen it here?11 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？The space（room） is too small between the lifter and the boss. The angular lifter interferes with the boss during ejection（when moving）. Please c

5、onsider changing the position of the boss.12 这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？The rib here is too thin and relatively high, so it will be difficult to fill（走胶） here during the injection process, can we increase the thickness of this rib?13 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两种做法，1、做镶

6、件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？Are you going to increase or decrease the plastic（material） on this rib? For increasing plastic, we will use EDM. For decreasing plastic, there will be two options. One is to make inserts; the other is to weld the tool.Because there is water line under the inser

7、t, is that OK?14 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。The bottom of the rib was burned due to poor venting, we can add an insert in the middle of the rib to improve it.15 重做镶件大约需要5-6天时间，你能接受吗？It will take about 5 or 6 days to re-do the insert, is that OK?16 产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。可能

8、需要几天的时间。 所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？We have already textured this side. If we add material, it will take a few days to remake the texture. So we suggest using the EDM（ spark） finish instead of texturing, is that OK?17 模具是用公制/英制的配件？需要备用件吗？Are the mold parts in inches or mm? Do they need spare par

9、ts?18 模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。Will you provide the engraving content of the mold label? Please advise it asap.19 可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大小、呵林柱尺寸、顶棍孔尺寸等Can you provide the specifications of your injection machine? Such as the press size, tie bar space, Konck-out（K.O.）/ejector rods holes

10、 pattern.20 这个问题我需要同其它同事商议会再答复你。I will discuss it with my colleagues, and reply asap.21 我们将尽力达成你的计划，如有异常，会及时通知你。We will try our best to meet/ reach your plan. For any problems, we will notify you immediately/promptly.22.这个产品的长度为330.12MM,宽度为78.96MM,高度为45MM.胶厚为2MM,重量为70.63g,试模注塑机型号为250吨,胶料颜色为黑色,产品外表面晒

11、纹处理,内表面为抛光.需要日期章、环保章、材料章.前后模用2344氮硬，斜顶和行位座用738H，以上模具信息正确吗？请确认！Please check the information below and comment/approve.L. W. H =330.12 x 78.96 x 45MM, Thickness - 2MM. Weight - 70.63g, Press size - 250TColor of the T1 samples - black.Outer/visible surface finish texture; inner side polishing.Date code

12、, recycle stamp and material I.D. needed.CAV & Core - 2344 nitrided steel; Lifter and slider shelf/base/retainer - 738H. 23 现在到了吃午钣的时间，我们下午再继续好吗？Lunch time, shall we go for lunch now? We can discuss the project later.24.和滑块干涉的倒勾请加料填平至滑块可以顺利滑动The undercut area interferes with the slide block, so we s

13、uggest adding material to help the slider move smoothly.25. 加 胶太多 （The added wall/thickness is too much）26. 加肉面积太大 （The added area is too wide.）27.GATE位置移位 （ The gate location is moved.）28. 滑块拆的位置 （The split line of slide block or the area/location of slide.）29. 此处有尖角，填充困难 （It is hard to fill this a

14、rea due to the sharp feature.）30. 此处钢材太薄，强度不足而且不容易冷却（The steel is too thin, the strength of this area is too weak and it is hard to cool.）31. 圆柱特征要有一半圆不可以拆在滑块上，以免粘滑块造成拉白，拉断（We dont suggest designing half of the cylinder on the slide block because it will cause sticking and drag marks.）32. 此处做斜顶在作动时会

15、铲胶。（The part will be damaged if we make the lifter in this area.）33. 这个面是装配面，不能加胶。（This is a critical surface where we cannot add additional material.）34. 此处胶位太厚，会有缩水，建议减料改善（ The wall is too thick, there will be sink mark. We suggest reducing plastic to improve it.）35. 此面是不是外观面，此处做滑块的话会有夹线，是否可以接受Is

16、it a critical/visible surface? If we make a slide here, there will be asplit line. Is it OK?36. 此处有倒扣，能否不做滑块和斜顶？建议减胶使前后模碰穿？There is an undercut, can we/you reduce material to have kiss-off instead of making slide and lifter?37. 请尽快确认这种拆模方式和结构，否则会影响模期Please confirm the parting line and layout as soon

17、 as possible, otherwise, the lead time will be extended.38. 此面是否有特殊要求，能否有顶针印Please confirm whether it is a critical surface or not, and if we can have E.J. pin marks on it.39. P.L面开在此处，模具上会有尖角和刀口，对模具寿命有影响There are sharp edges if we set the parting line here, it will reduce the tool life.40. 加大拔模角，以便

18、脱模顺利We suggest enlarging the draft angle to help release/demold the tool.）41. GATE做在此处的话有两个缺点：1.盖子打开时可以看到GATE的修剪部位; 2.两个斜销在同一侧，顶出也不是很平衡.（There are two issues if the gate is to be designed in this area:a）. It is easy to see the gate/trimming mark when you open the cap.b）. The ejection is unbalanced w

19、hen two lifters are on the same side）42. GATE做在此处的话.盖子打开后看不到GATE的修剪部位（The gate mark is not visible if the gate location is designed like this.）43. 我们建议进胶做在这一侧，产品表面不会缩水。To avoid sink marks, we suggest gating on this side/surface.44. 在此处GATE做潜顶针的话，背后的外观面会有冲料痕，而且成品又是黑色的，会最明显If we sub-gate into an eject

20、or pin, the outer surface of the part will have serious flow marks. Since the part is in black, the marks will be more visible.43. P.L开在此处不合理，模具加工困难，P.L应改为和图示的一样If parting line is designed here, the tooling will be more difficult. Therefore,we recommend to have the parting line as indicated.45。产品粘前模

21、的机会很大，能否在后模加倒勾，拉料杆或者后模保留E.D.M纹，开模时使成品留在后模一侧We may have sticking on cavity, can we add undercuts and sprue puller? Or keep EDM grain to snatch the part on the core.46.此处胶位厚度不均匀，成品表面会有应力痕，是否接受Please confirm whether it is acceptable to have stress marks on the surface because the thickness is uneven.47

22、. 请注明何处为外观面，能否提供2D图和注意事项Please advise where the critical/visible surface is. Please also provide us a 2D drawing and other specifications.48. 红色所示处是有问题的地方，请特别注意Please note the red highlights because those areas have problems.49. 成品设计此处有问题，建议如附图所示修改（We would suggest using the attached part design as

23、the current design has problems.）50. 此处改为一个球形的凹槽 （We suggest modifying it as a spherical recess.）51. 圆柱特征要有一半不可以拆在滑块里，以防拉断 We dont suggest designing half of the cylinder on the slide block because it will cause drag marks.52. 此处大滑块上走小滑块，小滑块要先退，大滑块要做延迟There is a small slide on the big slide. The smal

24、l slide will recede before the big one moves.53. 滑块要用液压油缸抽芯以保证开合模顺序（The slide pins will use an oil cylinder to assure that the process is in proper order.）54. 这个面有装配，加料的话装配时会顶住，如图所示We cannot add material to this surface because it will intervene between the two parts when it is assembled.Please see

25、the attached sketch. 55. 可降低斜销面，增加成品些许肉厚来做变化We suggest descending the surface of lifter and thickening the part for improvement.56. 一半做斜销，一半直接脱模 （Half will have the lifter and the other will be molded directly.）57. 此处两个柱子重迭，有倒勾，不能直接脱模，要做SLIDEThese two bosses are overlapping with undercut, therefore

26、a slide needs to be made.58. 此处强制顶出 （This area needs force ejection.）59. 后模两段开模，这个地方先退 There will be two stages/steps ejection. It will recede first.60. 此处做镶件会有夹线，能否接受There will be an insert split line here. Please confirm. 61. 此面前后模1度靠破/插穿，会有段差，可否接受（Please confirm whether it is ok to have mismatch

27、to the area where there is 1 degree of shut off in Core / Cavity side.）62. 这个尺寸能否加大 （Please confirm whether we can enlarge this dimension.）63. 此处加一个凹槽，胶片的弹出效果会更好一些，试模后看装配的效果再做修正（The elastic of the film will be better if we add a recess. We will see how it will affect the assembly parts,and then make

28、 modifications.）64. 此处有倒扣，建议将剖面线所示部位移除来避免此处的倒扣（There is an undercut here, we suggest cutting out the indicated part/area to avoid it.）65. 成型后潜水口要修平 （The gate （sub gate） needs to be trimmed perfectly after being molded.）66. 此处倒扣先直接顶出，之后再手动取出（The undercut needs to be ejected directly/straightly, then

29、the part will be taken out by hand/manually.）67. 这两个面都有滑块，GATE改在此处改不到（The gate is not suitable in this area because there are two sliders.）68. 此处加做一个节流阀/调节阀，射出时方便调整成品的质量（We would suggest placing a runner shut-off insert to adjust the volume of part filling/the flow of the resin.）69. 此倒扣在滑块上强制脱模，倒扣是否

30、可以减小到0.6（This undercut will be molded/manufactured by force, please confirm whether it can be reduced to 0.6 mm.）70. 此柱子无法脱模，请确认是否是在转图时错位，能否提供客户的原始图档 data. ）（This boss is not releasable/can not be molded/manufactured. Please check the file again, if possible, send us the original database.71. 此柱子是实心的，会缩水 （The solid boss will shrink.）72. 这个面是否要咬花/晒纹，咬花番号/晒纹型号是什么，最小的拔模角要多大（Please confirm whether this surface needs to be tex