DIN EN 104321996金属材料焊缝破坏试验硬度试验第2部分焊接接缝显微硬度试验.docx

1、DIN EN 104321996 金属材料焊缝破坏试验硬度试验第2部分焊接接缝显微硬度试验DIN EN 1043-2-1996 金属材料焊缝破坏试验.硬度试验.第2部分焊接接缝显微硬度试验ICS 25.160 .40 DEUTSCHE NORM ardness testing of welds in metallic materials Micro hardness testing on welded joints English version of DIN EN 1043四2Descriptors: Testing , welded joints, hardness test, metal

2、s. November 1996 DIN EN 1043皿2Zerst?rend Prfung von Schwi?verbindungen an metallischen Werkstoffn 一 H?rteprfung Teil 2: Mikroh?rtprfung an Schwei?verbindungen European Standard EN 1043圄2: 1996 has the status 01 a DIN Standard 圄A comma is used as the decimal marker. National foreword This standard ha

3、s been prepared by CEN厅C 121. The responsible German body involved in its preparation was the Normenausschu Schwei?technik (Welding Standards Committee), Technical Committee Zerst?rende Prfung von Schwei?verbindungen. DIN 50133 is the standard corresponding to International Standards ISO 6507斗 and I

4、SO 6507-2 referred to in clause 2 of the EN. Standard referred to (and not included in Normative references) DIN 50133 Vickers hardness testing of metallic materials 一 HV 0 ,2 to HV 100 。 No part 01 this standard may be reproduced without the prior permission of DIN Deutsche8 In8tftut tr Normung e.

5、V. , Berlin. Beuth Verlag GmbH, Berlin, has the exclusive right 01 sale for German Standards (DIN-Normen). 巨N comprises 10 pages 阳Ref. No. DIN EN 1043回2:1996-11Price group 07 8ales No. 1107 05.97 EUROPEAN S?NDARD NORME 睦UROPEENNEEUROP?I串串HE NORM EN 1043-2 October 1996 ICS 25.160 .40 Descriptors: Tes

6、ting, welded joints, hardness test, metals. English version Destructive tests on welds in metallic materials Hardness test Part 2: Micro hardness testing on welded joints Essais destructifs des soudures sur matriaux mtalliques - Essai de duret -Partie 2: Essai de microduret des assemblags soud告$Zers

7、t?rende Prfung von Schwei?verbin-dungen an metallischen Werkstoffen -H?rteprfung - Teil 2: Mikroh?rteprfung an Schwei?verbindungen This European Standard was approved by CEN on 1996-05-23 固CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate th告 conditions for gi

8、ving this European Standard the status of a national standard without any alt串阳tion.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any C巨N member. This European Standard exists in three official versi

9、ons (English , French , German). A version in any other language made by translation under the responsibility of a CEN member into its own languag自 and notifi自d to the Central S自cr自tariat has the same status as the official verslons. CEN members are the national standards bodies of Austria , Belgium

10、, Denmark, Finland , France, Germany, Greece, Iceland , Ireland , Italy, Luxembourg, Netherlands, Norway, Por-tugal , Spain , Sweden , Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europ?isches Komitee fr Normung Central Secretariat: rue de

11、 Stassart 36, B-1050 Brussels 。 1996. CEN - AII rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN 1043国2: 1996 E Foreword.;.1111.11. 2 1 Scope .回.;. 3 2 Normative references . .四 a s g. . ? . .田.国. 3 3 Principle .回.;.团.植.国.，.;.国.田. 3 4 Denom

12、inations and symbols .， ?.II. 圄. 3 5 Preparation of test specimens. 自. 4 6 Test procedure .回.;.圃.田. . . 11 圃. 4 6.1 Rows of indentations (R) . . . . e 0 .国 0. . 4 6.2 Individual indentations (E) . u .嗣国. 5 7 Test results . . 5 8 Test report.,.;1;. 6 Annex A (informative) 时ardness testin由 (R) on weld

13、ed joints. ' 8 . 8.;'. ;'. 8. '. . . . . . 9 Annex B (informative) Hardness testing (E) on welded joints. .10 Foreword This European Standard has been prepared by Technical Committee CENITC 121 ;Weldi吨'thesecretariat of which is held by DS. This European Standard shall be gi

14、ven the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Apri11997, and conflicting national standards shall be withdrawn at the latest by April 1997. According to the CEN/CENELEC Intemal Regulations , the national standards organizations

15、of the following countries are bound to implement this European Standard: Austria , Belium ， Denma础，Finla时， France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, No阳ay ，PO叫ugal ， Spain , Sweden, Switzerland and the United Kingdom. Page 3 EN 1043-2: 1996 This standard specifies m

16、cro hardness tests on transverse sections of welded joints of metallic materials with high hardness radients. It covers Vickers hardness tests in accordance with 180/D!8 6507斗， normally with test loads of 0 ， 9自 N to less than 49 N (HV 0 ,1 to less than HV 5). Testing should be carried out to ensure

17、 that the highest and/or the lowest level of hardness of both parent metal (in the case of dissimilar metal both parent metal) and weld metal is determined 圃The type and extent of testin sha!l be as specified by an application standard or by agreement between the contracting parties. This standard d

18、oes not cover the hardness test as described in EN 1043斗，2 Normative references This European 8tandard inco币。rates ， by dated or undated reference雷 provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter

19、. For dated references, subsequent amendments to or revisions of any of these publications apply to this European 8tandard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 1043-1 Oestructive test on welds in m

20、etallic materials - Hardness testing - Part 1: Hardness test on arc welded joints 180/018 6507-1: 1995 Metallic materials - Vickers Hardness test 翩 Part 1 : Test method 3 Principle 时icro hardness testing shall be carried out in accordance with 180/018 6507-1. The micro hardness tests may be carried

21、out in the form of rows of indentations冒民， or as individual indentations, E. When types of weld are not shown in the examples, the test procedure shall be appropriate to the welded joint. Unless otherwise specified , the test shall be carried out at ambient temperature (23 士码。C4 Denomination5 and 5y

22、n啦。15The denominations and symbols to be used are specified in table 1 and represented on figures 1 to 3. Table 1 : Denominations and symbols 8ymbol Oesgnation Unit E Individual indentation R Row of indentation HV Vickers hardness L Oistance between the centrepoint of the indentations in mm heat aff

23、ected zone H Oistance of rows of indentations from the reference line 阿1门1(surface or fusion line) Thickness of test specimen mm 1) The unit of symbolisation for Vickers hardness is given in 180/018 6507斗 E5 Preparation of test specimens The preparation of the test specmen shall be in accordance wth

24、 180/018 6507四 1.A cross-section of test piece shall be taken by mechanical cutting , usually transverse to the welded joint. This operation and the subsequent preparation of the surface shall be carried out carefully so that the hardness of the surface to be tested is not affected metallurgically.

25、The surface to be tested shall be properly prepared and preferably etched, so that accurate measurements of the diagonal of the indentations can be achieved in the different zones of the welded joint. 6 Test procedure 6.1 Rows of indentations (R) Fiures 1 to 3 give examples of hardness indentations

26、made in rows including the distance from the surface so that these rows or parts of them permit an assessment of the welded joint. If required by the contracting parties, additional rows of indentations and/or different locations may be made. The location shall be stated in the test report. In metal

27、s such as aluminium, copper and their alloys, the rows on the root-side of butt welds (see fiure 1) can not be necessary. The number and spacin窜。f indentations shall be sufficient to define hardened or softened regions due to welding. Recommended distance between the centrepoint of the indentations

28、in the heat affected zone (HAZ) s gven n table 2. Page 5 EN 1043-2: 1996 Sufficient indentations shall be made to ensure that unaffected parent metal is tested. In the weld metal, the distance between indentations shall be selected and checked so that the results obtained will enable assessment of the welded joint to be ma