Boat Maintenance中文船体维护.docx

1、Boat Maintenance中文船体维护Boat Maintenance船体维护A boats gel coat forms the outer skin of its fibre glass hull. Its a layer of pigmented resin,which protects the surface of the boat, sealing the fibre glass beneath from the elements from water, moisture and the suns ultraviolet rays. Gel coat also gives th

2、e boat its colour and provides its attractive glossy finish.玻璃纤维船体的胶衣就好比人的皮肤表面一样。它是一层颜料树脂，覆盖住船的表面，保护下面的玻璃纤维免受海水，降雨以及紫外线等恶劣环境的影响。同时胶衣可以选择不同的颜色同时具有吸引人的光泽。Damage occurs to the gel coat simply by being in the harsh marine environment, particularly from the suns ultraviolet rays. Oxidation can occur, whi

3、ch results in a dull, chalky appearance.The extent of this oxidation, dictates which tactics should be used to restore the original finish- in most cases, oxidation of the boats gel coat is easily remedie.恶劣的海洋环境会损害胶衣，特别是来自太阳的紫外线。发生氧化的会使胶衣产生沙眼、裂缝以及外观的粗糙。船的胶衣是容易氧化的，所以必须根据氧化的程度来判断采取何种方法进行修复。While the

4、sun is the gel coats worst enemy, care must also be taken to protect it from water and abrasion. Abrasions can occur simply when dirt is ground into the deck, or through nicks and scratches from mooring. A worn or scratched gel coat can allow water to permeate the fibre glass, causing serious damage

5、 over time尽管阳光是胶衣最大的敌人，但来自海水的腐蚀和人为的磨损也不能忽视。磨损的产生可能是陆地的沙土进入船上造成，或者人为的碰撞划痕以及停泊时的磨擦。胶衣的磨损或刮伤会让水渗入到玻璃纤维，随着时间的推移造成严重损害。The best plan of action is to clean and protect your new boat from the start using a simple gel coat maintenance plan. Because the gel coat maintains the integrity of the fibre glass ben

6、eath it, and gives your boat a shiny, well-maintained look, attention to cleaning and protecting thegel coat will preserve it for years to come.胶衣的简单维护最好是新船到了之后进行清理和保养。胶衣不仅仅只保护它下面的玻璃纤维，还能使船的外观保持亮丽有光泽。所以要使船的外观保持亮丽有光泽，必须注意清洗和保护胶衣。Maintenance Plan维护计划Part 1第一部分Use dedicated fibre glass cleaners, such a

7、s 3M Marine Fibreglass Cleaner and Wax this has a PH of 4-7.使用专用的玻璃纤维清洁剂，如3M MarineFibreglass Cleaner and Wax 它的PH值在4-7之间。Do not use a cleaner containing the following: Strong Alkali,Ammonia, Bleach or High Acidic.不要使用包含以下添加剂的清洁产品：强碱，氨水，漂白剂或强酸性。After soaping always rinse very well using fresh water

8、it is vital that all cleaner residue is removed.使用清洁剂清洗后最好能用淡水再冲洗一遍，这是很重要的。要确保清洁剂残留物被彻底洗净。Do not leave water to dry in direct sunlight, where practical remove excess water droplets with an absorbent material such as leather or use a squeegee. If water is left on a surface in direct sunlight, it acts

9、 as a magnifier and intensifies the suns harmful effects on the surface accelerating the weathering process.洗完船需要把表面的水用吸水抹布擦干，不要让水停留在上面被阳光晒干。因为在阳光照射下，表面的水会具有放大镜的效果，对下面的胶衣产生有害的影响。To remove dirt and mild stains, many fibre glass cleaners are available from chandlery stores. There are many types of spe

10、cialty cleaners, including some with wax to protect the gel coat. Others are a two part process of cleaning and waxing. Both are useful in the protecting phase of the program.要清除船表面的污垢和脏物，许多船都是使用从杂货店买来的清洁剂。其实应该使用专业的清洁剂，包括保护胶衣的蜡水。过程分为两个步骤：清洁和上蜡。这两个程序都是用来保护胶衣的。Part 2第二部分After thoroughly cleaning the g

11、el coat with boat wash the next step in protecting your boats gel coat is waxing. At this stage, experts vary on the type of wax, but most generally agree that applying wax is essential to maintaining the integrity and shine of your boats gel coat.在洗船液彻底的清洗船表面后，下一步应该是给胶衣打蜡，起保护作用。打蜡的原因虽然有很多不同的说法，但是大多

12、数人都同意是为了保护胶衣的完整性和保持光泽。Most fibreglass boat waxes are beeswax based, carnauba wax, silicone or a combination of these. All are designed to protect the gel coat from ultraviolet rays and the harsh marine environment. We recommend you use 3M Ultra Performance Paste wax (see photo).大多数玻璃纤维的船蜡是用蜂蜡为原料与巴西棕

13、榈蜡、硅酮混合。所有这些设计都是为了使胶衣能抵御紫外线和恶劣的海洋环境。我们推荐你使用3M Ultra Performance Paste wax（看图片）。You should apply two coats of wax ensuring that when applying you leave the wax to set, you will have to leave for 30 40 mins between coats. This will provide a good protective barrier coat. Depending on the climate you s

14、hould try to apply every month after wash down.你应该打两层蜡（粗蜡和细蜡），两次之间的间隔应该在30-40分钟，这样能更好的保护胶衣。根据不同的气候，你应该每个月至少重新打蜡一次。Other ways to protect your boats gel coat is to use fenders with washable covers to ward off accidental dings and scrapes. Since ultraviolet rays do the most damage, actually covering yo

15、ur boat will preserve the life of gel coat.其他保护你船体胶衣的方法是使用有保护套的可清洗碰垫套，防止碰垫跟船之间的磨损。由于紫外线对胶衣的损害最大，因此盖上船罩将会延长胶衣寿命。Signs of Oxidation氧化迹象If the surface of your boat appears dull or chalky, it is likely that your gel coat has oxidized. Gel coat oxidation is easily remedied in most cases.如果你的船表面出现无光泽或白色粉状

16、，很可能是你的胶衣已被氧化。胶衣氧化在大多数情况下很容易补救。Light Oxidation光氧化If your boats gel coat is slightly oxidized, most of the surface will be shiny with a few patches of dullness or cloudiness.如果你船的胶衣是轻微氧化，就是只有一些地方无光泽，大部分还是有光泽的。At this stage of oxidation, a simple oxidation removing compound applied to the hull will re

17、move oxidation and restore the shine. We would recommend 3M Fast Cut (white or Green top)在这个氧化阶段，应该使用容易去除氧化使船体恢复光泽的产品。我们推荐3M Fast Cut（白或绿盖）This is a cutting compound, which needs to be used an electric variable speed polisher with the speed setting at about 1,500 rpm. Use a yellow soft woollen mop a

18、s below.这是一个去除氧化物的过程，必须使用电动变速抛光机，速度设定在大约1500转/分钟。然后使用黄色柔软的羊毛擦。This is a cutting compound, which needs to be used with speed setting at about 1,500 rpm. Use a 3M Superbuff III. (Yellow in colour).这是一个去除氧化物的过程，需要把速度设定在大约1500转/分钟。使用3M Superbuff III。（黄色）Apply compound to the effected area then use the p

19、olisher to remove the dull gel coat. Once you have polished the area you will then need to apply 2 coats of wax to seal the newly restored finish.使用抛光机和蜡水去除胶衣表面的无光泽区域。一旦你已经抛光这个区域，你还需要打两次蜡（粗蜡和细蜡）来完成修复。3M Superbuff III Yellow (soft)3M Superbuff III 黄色（软的）3M Superbuff III white (medium)3M Superbuff III

20、 白色（中等的）Medium Oxidation中等氧化The entire surface of the boat will be dull, flat and unreflective plus there may be signs of pitting. To remove the oxidation and smooth the pitting, you will need to use the same 3m Fast Cut as used with Light Oxidation but with a coarser 3M Superbuff polishing mop (whi

21、te in colour)这个程度将使船的整体表面都比较没有光泽，不平以及一些点蚀的迹象。去除氧化和点蚀，你需要使用相同的3m Fast Cut 用于去除光氧化，但是要使用比较粗的3M Superbuff 抛光圆饼（白色）3M Fast Cut is similar to fine sandpaper, it removes the surface rather than coating it.3M Fast Cut是同类中最好的砂纸，它只去除了表面凹痕而不是整个涂层。Once you have polished the area you may see polishing swirls -

22、you then need to go over the area again using the softer 3M Superbuff yellow mopwith a fine cut compound such as 3m Finesse-It.一旦你已经打磨了抛光区域后你可以看见上面的纹路，这时你需要更细的3M Superbuff黄色圆饼和蜡水，如3m Finesse-It重新抛光刚才的区域。The final process is to apply two coats of wax ensuring that when applying you leave the wax to s

23、et, you will have to leave for 30 40 mins betweencoats. This will provide a good protective barrier coat.最后的工序是打两次蜡，粗蜡打完间隔30-40分钟再打细蜡。这将给胶衣提供最好的保护。Depending on the climate you should try to apply every month after wash down.根据不同的气候，你应该每个月至少重新打蜡一次。Signs of Heavy Oxidation重氧化迹象The entire surface of th

24、e boat will have no reflectivity and may be chalky to the touch - pitting is obvious. At this stage of oxidation, washing, sanding and polishing are required. In most cases though, restoration will mean intense work to restore the shine and may require the attention of a professional.船的整体表面没有光泽，有白色粉

25、末，触碰有明显点蚀感觉。这种氧化程度，冲洗，打磨，抛光是必需的。大多数情况下，想要恢复光泽是需要比较复杂的程序，而且可能需要专业的技术。Boat Restoration船修复Time,weather,sun and salt all take their toll on your boats surfaces.3Ms marine supplies feature an extensive range of boat restoration products that are cleverly designed to restore a boats finish depending on th

26、e amount of oxidation that needs to be removed.时间，天气，太阳和盐分都会损耗你的船表面。3M船用修复系列产品范围广泛，船的保养取决于需要去除的船体饰面氧化量的多少。Removing Heavy Oxidation去除重氧化Removing heavy oxidation requires using a more aggressive compound with a compounding pad to secure a professional result.It is important to avoid leaving the buffin

27、g pad in one spot for too long as this may damage the paint or gelcoat and it is always a good idea to practise with the buffer before beginning to avoid burning through and deep swirl marks.Suggested Product:3M Marine Imperial Compound or Finishing Material 06044E去除重氧化需要使用更多活性化合物以及组合垫来确保专业的效果。重点是避免

28、抛光垫在一个地方停留太长时间，因为这可能会破坏油漆或者胶衣。开始抛光之前在缓冲区先进行练习总会是不错的选择，用于避免磨穿和留下深螺旋纹。建议使用产品：3M Marine Imperial Compound or Finishing Material 06044ERemoving Minor Scratches and Returning the Boats Shine去除轻微划痕和恢复船的光泽After using an aggressive compound to removed any remaining minor scratches or swirl marks and to rest

29、ore the original high gloss finish follow with a boat glaze.As s final stage to prevent surface fading and protect against UV damage apply a boat wax.Suggested Product:3M Marine Finesse it 11 finishing material 09048E使用活性化合物去除一些较小的划痕或漩涡痕迹之后要紧跟着上船用釉使其恢复原来的高光泽。最后阶段预防船表面褪色，保护不受紫外线影响应使用船蜡。建议产品：3M Marine

30、 Finesse it 11 finishing material 09048EFollowed by:3M Marine Liquid Wax 09027E or 3M Marine Ultra Performance Paste Wax 09030E applied using any 3M Scotch Brite High performance cloth HPW 2010依次是：3M Marine Liquid Wax 09027E 或者 3M Marine Ultra Performance Paste Wax 09030E，也可以使用3M Scotch Brite的高性能打蜡布

31、 HPW 2010。Removing Light Oxidation去除轻微氧化When completing tasks such as removing small rust spots,stains and light oxidation that occur on newer boats a less aggressive compound is more suitable then heavy duty cleaners.Apply a small amount of fibreglass cleaner on a rag or for larger areas buff out t

32、he spot with a Superbuff Pad,then wipe it off with a dry cloth.Suggested Product:3M Marine Fibreglass Cleaner and wax 09010E applied using 3M High Performance Cloth or any 3M Marine Superbuff pad当完成任务（例如去除小的蚀斑，污点和光氧化）后，船表面残留的活性化合物必须清洁干净。应用上打蜡布或在更大的区域内使用Superbuff和少量清洁剂，然后用干布擦拭。建议产品：3M Marine Fibreglass Cleaner and wax 09010E 也可以使用 3M High Performance Cloth 或者其它的 3M Marine Superbuff padRestoring and Polishing Metals恢复和抛光金属Over time metal surfaces such a