模具专业英语词汇doc.docx
《模具专业英语词汇doc.docx》由会员分享,可在线阅读,更多相关《模具专业英语词汇doc.docx(57页珍藏版)》请在冰豆网上搜索。
模具专业英语词汇doc
模具专业英语词汇
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模 英语站
landed positive mold 有肩全压式模具
button die 镶入式圆形凹模
loading shoe mold 料套式模具
center-gated mold 中心浇口式模具
loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模
composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
modular mold 组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具
electroformed mold 电铸成形模
multi-gate mold 复式浇口模具
expander die 扩径模
offswt bending die 双折冷弯模具
extrusion die 挤出模
palletizing die 叠层模
family mold 反套制品模具
plaster mold 石膏模
blank through dies 漏件式落料模
porous mold 通气性模具
duplicated cavity plate 复板模
positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具
progressive die 顺序模
gypsum mold 石膏铸模
protable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具
sectional die 拼合模
runless injection mold 无流道冷料模具
sectional die 对合模具
segment mold 组合模
semi-positive mold 半全压式模具
shaper 定型模套
single cavity mold 单腔模具
solid forging die 整体锻模
split forging die 拼合锻模
split mold 双并式模具
sprueless mold 无注道残料模具
squeezing die 挤压模
stretch form die 拉伸成形模
sweeping mold 平刮铸模
swing die 振动模具
three plates mold 三片式模具
trimming die 切边模
unit mold 单元式模具
universal mold 通用模具
unscrewing mold 退扣式模具
yoke type die 轭型模
accurate die casting 精密压铸
powder forming 粉末成形
calendaring molding 压延成形
powder metal forging 粉末锻造
cold chamber die casting 冷式压铸
precision forging 精密锻造
cold forging 冷锻
press forging 冲锻
compacting molding 粉末压出成形
rocking die forging 摇动锻造
compound molding 复合成形
rotary forging 回转锻造
compression molding 压缩成形
rotational molding 离心成形
dip mold 浸渍成形
rubber molding 橡胶成形
encapsulation molding 注入成形
sand mold casting 砂模铸造
extrusion molding 挤出成形
shell casting 壳模铸造
foam forming 发泡成形
sinter forging 烧结锻造
forging roll 轧锻
six sides forging 六面锻造
gravity casting 重力铸造
slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形
squeeze casting 高压铸造
hot chamber die casting 热室压铸
swaging 挤锻
hot forging 热锻
transfer molding 转送成形
injection molding 射出成形
warm forging 温锻
investment casting 精密铸造
matched die method 对模成形法
laminating method 被覆淋膜成形
low pressure casting 低压铸造
lost wax casting 脱蜡铸造
matched mould thermal forming 对模热成形模
bismuth mold 铋铸模
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模
landed positive mold 有肩全压式模具
button die 镶入式圆形凹模
loading shoe mold 料套式模具
center-gated mold 中心浇口式模具
loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模
composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
modular mold 组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具
electroformed mold 电铸成形模
multi-gate mold 复式浇口模具
expander die 扩径模
offswt bending die 双折冷弯模具
extrusion die 挤出模
palletizing die 迭层模
family mold 反套制品模具
plaster mold 石膏模
blank through dies 漏件式落料模
porous mold 通气性模具
duplicated cavity plate 复板模
positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具
progressive die 顺序模
gypsum mold 石膏铸模
protable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具
sectional die 拼合模
runless injection mold 无流道冷料模具
sectional die 对合模具
segment mold 组合模
semi-positive mold 半全压式模具
shaper 定型模套
single cavity mold 单腔模具
solid forging die 整体锻模
split forging die 拼合锻模
split mold 双并式模具
sprueless mold 无注道残料模具
squeezing die 挤压模
stretch form die 拉伸成形模
sweeping mold 平刮铸模
swing die 振动模具
injection mold 注塑模
rubber molding 橡胶成形
hot chamber die casting 热室压铸
sand mold casting 砂模铸造
extrusion mold 挤出模
multi-cavity mold 多模穴模具
palletizing die 叠层模
plaster mold 石膏模
three plates mold 三板模
plain die 简易模
pierce die 冲孔模
forming die 成型模
progressive die 连续模
gang dies 复合模
shearing die 剪边模
riveting die 铆合模
compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控 母模
core 模心 公模
runner system浇道系统
sprue/cold material trap 浇道/冷料井
sprue puller 拉杆
runner design 流道设计
main runner 主流道
secondary runner 次流道
gate design 浇口设计
submarine gate 潜伏浇口
tunnel gate 隧道式浇口
pinpoint gate 点浇口
fan gate 扇形浇口
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
dish gate 盘形浇口
diaphragm gate 隔膜浇口
ring gate 环形浇口
Runner less 无浇道
(sprue less) 无射料管方式
long nozzle 延长喷嘴方式
sprue 浇口;溶渣
insulated runner/hot runner 热浇道
runner plat 浇道模块
valve gate阀门浇口
slag well 冷料井
cold slag 冷料渣
sprue gate 射料浇口,直浇口
nozzle 射嘴
sprue lock pin 料头钩销(拉料杆)
注塑缺陷:
flash 飞边
warpage 翘曲
air trap 积风
blush 发赤
flow line 流痕
splay 银纹
short shot 短射
sink mark 缩痕
streak 条纹
void 缩孔
weld line 熔接线
gas mark 烧焦
cold slug 冷斑
delamination 起皮
burr 毛刺
flaw/scratch 刮伤
gloss 光泽
glazing 光滑
surface check 表面裂痕
hesitation 迟滞
注塑工艺:
molding conditions 成型条件
drying 烘干
barrel temperature 料筒温度
melt temperature 熔化温度
mold temperature 模具温度
injection pressure 注塑压力
back pressure 背压
injection speed 注塑速度
screw speed 螺杆转速
tensile strength 抗拉强度
tensile elongation 延伸率
flexural modulus 弯曲模数
flexural strength 抗弯强度
shrinkage 收缩率
regrind usage 次料使用
机械设备:
lathe车床
planer |刨床
miller 铣床
grinder 磨床
driller 钻床
linear cutting 线切割
electrical sparkle 电火花
welder 电焊机
punching machine 冲床
robot机械手
common equipment常用设备
EDM=Electron Discharge Machining 放电加工
3D coordinate measurement 三次元量床
boring machine 搪孔机
milling machine 铣床
contouring machine 轮廓锯床
copy grinding machine 仿形磨床
cylindrical grinding machine 外圆磨床
die spotting machine 合模机
engraving machine 雕刻机
engraving E.D.M. 雕模放置加工机
form grinding machine 成形磨床
graphite machine 石墨加工机
horizontal boring machine 卧式搪孔机
horizontal machine center 卧式加工制造中心
internal cylindrical machine 内圆磨床
模具零件:
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
inner guiding post内导柱
inner hexagon screw内六角螺钉
dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒
pin销
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
模具述语
一、入水:
gate
进入位:
gate location
水口形式:
gate type
大水口:
edge gate
细水口:
pin-point gate
水口大小:
gate size
转水口:
switching runner/gate
唧嘴口径:
sprue diameter
二、流道:
runner
热流道:
hot runner,hot manifold
热嘴冷流道:
hot sprue/cold runner
唧嘴直流:
direct sprue gate
圆形流道:
round(full/half runner
流道电脑分析:
mold flow analysis
流道平衡:
runner balance
热嘴:
hot sprue
热流道板:
hot manifold
发热管:
cartridge heater
探针:
thermocouples
插头:
connector plug
插座:
connector socket
密封/封料:
seal
三、运水:
water line
喉塞:
line lpug
喉管:
tube
塑胶管:
plastic tube
快速接头:
jiffy quick connector plug/socker
四、模具零件:
mold components 三板模:
3-plate mold
二板模:
2-plate mold
边钉/导边:
leader pin/guide pin
边司/导套:
bushing/guide bushing
中托司:
shoulder guide bushing
中托边L:
guide pin
顶针板:
ejector retainner plate
托板:
support plate
螺丝:
screw
管钉:
dowel pin
开模槽:
ply bar scot 撑头:
support pillar
唧嘴:
sprue bushing
挡板:
stop plate
定位圈:
locating ring
锁扣:
latch
扣鸡:
parting lock set
推杆:
push bar
栓打螺丝:
S.H.S.B
顶板:
eracuretun
活动臂:
lever arm
分流锥:
spure sperader
水口司:
bush
垃圾钉:
stop pin
隔片:
buffle
弹弓柱:
spring rod
弹弓:
die spring
中托司:
ejector guide bush
中托边:
ejector guide pin
镶针:
pin
销子:
dowel pin
波子弹弓:
ball catch
喉塞:
pipe plug
锁模块:
lock plate
斜顶:
angle from pin
斜顶杆:
angle ejector rod
尼龙拉勾:
parting locks
活动臂:
lever arm
复位键、提前回杆:
early return bar
气阀:
valves
斜导边:
angle pin
术语:
terms
承压平面平衡:
parting surface support balance
模排气:
parting line venting
回针碰料位:
return pin and cavity interference
模总高超出啤机规格:
mold base shut hight
顶针碰运水:
water line interferes withejector pin
料位出上/下模:
part from cavith (core) side
模胚原身出料位:
cavity direct cut on A-plate,core direct cut on B-plate.
内模管位:
core/cavity inter-lock
顶针:
ejector pin
司筒:
ejector sleeve
司筒针:
ejector pin
推板:
stripper plate
缩呵:
movable core,return core core puller
扣机(尼龙拉勾):
nylon latch lock
斜顶:
lifter
模胚(架):
mold base
上内模:
cavity insert
下内模:
core insert
行位(滑块)