单片机串口控制继电器的C源程序.docx
《单片机串口控制继电器的C源程序.docx》由会员分享,可在线阅读,更多相关《单片机串口控制继电器的C源程序.docx(21页珍藏版)》请在冰豆网上搜索。
单片机串口控制继电器的C源程序
51单片机串口控制继电器的C源程序
2009-09-2923:
13
计算机通过软件来控制单片机继电器。
操作:
计算机使用串口调试助手,当然,可以自己编写控制软件(上位机软件)。
单片机P1.1口连上继电器
C源程序为:
#include
sbitRELAY=P1^1; //定义继电器:
接P1^1
voiddelay(unsignedintcnt)
{
while(--cnt);
}
main()
{
TMOD=0x20; //
TH1=0xfd;
TL1=0xfd;
SM0=0;
SM1=1;
REN=1;//控制RI
TR1=1;
/*以上为定时器设置和波特率设置,这样的话,通过串口调试助手发送数据(随意数据)通过改变RI(串口接收标志来实现继电器的吸合与打开 */
while
(1)
{
if(RI==1)
{
RI=0;
delay(500);
RELAY=!
RELAY; //如果吸合则打开,如果己打开则吸合。
}
}
}
以上在AT89s52+Keil上编译调试运行OK。
/****************************************************************************/
/* 电子日历,有时间显示、闹铃、日期、秒表及键盘设置功能 */
/*功能键A:
设置位数字+1 闹钟模式下为闹钟开关 秒表模式下为记时开关 */
/*功能键B:
设置位数字-1 闹钟模式下为闹钟开关 */
/*功能键C:
设置模式及设置位选择 秒表模式下为清零键 */
/*功能键D:
在四种工作模式下切换设置闹钟开关 */
/****************************************************************************/
#include
#include
/***************这里设置程序初始化时显示的时间****************/
#defineSET_HOUR12 /*设置初始化小时*/
#defineSET_MINUTE00 /*设置初始化分钟*/
#defineSET_SECOND00 /*设置初始化秒数*/
/*************************系统地址****************************/
#defineBASE_PORT0x8000 /*选通基地址*/
#defineKEY_LINEBASE_PORT+1 /*键盘行线地址*/
#defineKEY_COLUMNBASE_PORT+2 /*键盘列线地址*/
#defineLED_SEGBASE_PORT+4 /*数码管段选地址*/
#defineLED_BITBASE_PORT+2 /*数码管位选地址*/
#defineLED_ON(x)XBYTE[LED_BIT]=(0x01<25px;">
#defineLED_OFFXBYTE[LED_SEG]=0x00 /*LED显示空*/
/**************在设置模式下对秒分时的宏定义*****************/
#defineSECOND0 /*对应数码管右边两位*/
#defineMINUTE1 /*对应数码管中间两位*/
#defineHOUR2 /*对应数码管左边两位*/
/********************定义四种工作模式***********************/
#defineCLOCKclockstr/*时钟模式*/
#defineALARTalartstr/*闹钟模式*/
#defineDATEdatestr /*日期模式*/
#defineTIMERtimerstr/*秒表模式*/
/****************以下是所有子函数的声明*********************/
voidsys_init(void); /*系统的初始化程序*/
voiddisplay(void); /*动态刷新一次数码管子程序*/
voidclockplus(void); /*时间加1S的子程序*/
voidupdate_clockstr(void); /*更新时间显示编码*/
voidupdate_alartstr(void); /*更新闹钟时间的显示编码*/
voidupdate_datestr(void); /*更新日期显示编码*/
voidupdate_timerstr(void); /*更新秒表时间的显示编码*/
voiddeley(int); /*延时子程序*/
voidupdate_dispbuf(unsignedchar*); /*更新显示缓冲区*/
unsignedchargetkeycode(void); /*获取键值子程序*/
voidkeyprocess(unsignedchar); /*键值处理子程序*/
unsignedchargetmonthdays(unsignedint,unsignedchar);/*计算某月的天数子程序*/
/*功能键功能子函数*/
voidAkey(void); /*当前设置位+1开关闹钟开关秒表*/
voidBkey(void); /*当前设置位-1开关闹钟*/
voidCkey(void); /*设置位选择 秒表清零*/
voidDkey(void); /*切换四种工作模式*/
/**********************全局变量声明部分*********************/
unsignedcharled[10]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F};/*从0~9的LED编码*/
unsignedcharledchar[3]={0x5c,0x54,0x71};/*onf*/
//unsignedcharkey[24]={ /*键值代码数组对应键位:
*/
// 0x70,0x71,0x72,0x73,0x74,0x75, /* 7 8 9 ATRACERESET*/
// 0xb0,0xb1,0xb2,0xb3,0xb4,0xb5, /* 4 5 6 BSTEP MON*/
// 0xd0,0xd1,0xd2,0xd3,0xd4,0xd5, /* 1 2 3 CHERE LAST*/
// 0xe0,0xe1,0xe2,0xe3,0xe4,0xe5}; /* 0 F E DEXEC NEXT*/
struct{ /*时间结构体变量*/
unsignedchars;
unsignedcharm;
unsignedcharh;
}clock={SET_SECOND,SET_MINUTE,SET_HOUR};
struct{ /*闹铃时间结构体变量*/
unsignedcharm;
unsignedcharh;
}alart={SET_MINUTE,SET_HOUR};
struct{ /*日期结构体变量*/
unsignedintyear;
unsignedcharmonth;
unsignedcharday;
}date={6,1,1};
struct{ /*秒表时间结构体变量*/
unsignedcharms;
unsignedchars;
unsignedcharm;
}timer={0,0,0};
unsignedchardispbuf[6]; /*显示缓冲区数组*/
unsignedcharclockstr[6]; /*时间显示的数码管编码数组*/
unsignedcharalartstr[6]; /*闹钟显示的数码管编码数组*/
unsignedchardatestr[6]; /*日期显示的数码管编码数组*/
unsignedchartimerstr[6]; /*秒表显示的数码管编码数组*/
unsignedintitime=0,idot; /*定时器0中断计数*/
unsignedcharitime1=0; /*定时器1中断计数*/
sbitP3_1=P3^1; /*外接蜂鸣器的管脚*/
bdatabitIsSet=0; /*设置模式标志位 0:
正常走时1:
设置模式*/
bdatabitAlart_EN=0; /*闹铃功能允许位 0:
禁止闹铃1:
允许闹铃*/
bdatabitIsBeep=0; /*响铃标志位 0:
未响铃 1:
正在响铃*/
unsignedcharSetSelect=0; /*在设置模式IsSet=1时,正在被设置的位,对应上面的宏*/
unsignedchar*CurrentMode;/*标志当前正设置的功能,如CurrentMode=CLOCK或CurrentMode=ALART等*/
voidtimerplus(void);
/**************************函数部分*************************/
voidmain(void)
{
sys_init();
while
(1)
{
XBYTE[KEY_COLUMN,0x00]; /*给键盘列线赋全零扫描码,判断是否有键按下 */
while((XBYTE[KEY_LINE]&0x0f)==0x0f) /*检测是否有键按下,无则一直进行LED的刷新显示*/
{
if(Alart_EN&&(clock.h==alart.h)&&(clock.m==alart.m)){IsBeep=1;}
else
{IsBeep=0;
P3_1=0;}
display();
}
keyprocess(getkeycode()); /*有键按下时得到键值,并送入键值处理程序*/
display(); /*可要可不要*/
}
}
voidsys_init(void)
{
TMOD=0x22; /*定时器0和1都设置为工作方式2,基准定时250×2=500us=0.5ms*/
TH0=6; /*定时器0中断服务用来产生1秒时钟定时及闹钟蜂鸣器蜂鸣脉冲*/
TL0=6; /*定时器1中断服务留给秒表使用,产生1/100秒定时*/
TH1=6;
TL1=6;
ET0=1;
ET1=1;
EA=1;
TR0=1;
update_clockstr(); /*初始化时钟显示编码数组*/
update_alartstr(); /*初始化闹钟显示编码数组*/
update_datestr(); /*初始化日期显示编码数组*/
update_timerstr(); /*初始化秒表显示编码数组*/
update_dispbuf(clockstr);/*初始化显示缓冲数组*/
CurrentMode=CLOCK; /*默认的显示摸式为时钟*/
P3_1=0; /*蜂鸣器接线引脚复位*/
}
voidtimer0(void)interrupt1using1 /*定时器0中断服务器,用来产生1秒定时*/
{
itime++;
if(itime==1000)
{
if(IsSet) /*在设置模式下,对正在设置的位闪烁显示*/
{
dispbuf[SetSelect*2]=0; /*对正在设置的位所对应的显示缓冲区元素赋0,使LED灭*/
dispbuf[SetSelect*2+1]=0;
}
if(IsBeep)P3_1=!
P3_1; /*闹钟模式时,产生峰鸣器响脉冲*/
if(CurrentMode==CLOCK)
{
dispbuf[2]=dispbuf[2]&0x7f;
dispbuf[4]=dispbuf[4]&0x7f;
}
}
if(itime==2000) /*两千次计数为1S 2000×0.5ms=1s*/
{
itime=0; /*定时1s时间到,软计数清零*/
clockplus(); /*时间结构体变量秒数加1*/
update_clockstr(); /*更新时间显示编码数组*/
if(CurrentMode!
=TIMER)update_dispbuf(CurrentMode); /*用时间编码数组更新显示缓冲区*/
}
}
voidtimer1(void)interrupt3using2 /*定时器1中断服务器,用来产生1/100秒定时*/
{
idot++;
if(++itime1==20) /*20*0.5ms=10ms*/
{
itime1=0;
timerplus();
update_timerstr();
if(CurrentMode==TIMER)
{
update_dispbuf(timerstr);
dispbuf[2]=dispbuf[2]&0x7f; /*关闭小数点的显示*/
dispbuf[4]=dispbuf[4]&0x7f;
if(idot<1000) /*闪烁显示小数点*/
{
dispbuf[2]=dispbuf[2]|0x80;
dispbuf[4]=dispbuf[4]|0x80;
}else{
dispbuf[2]=dispbuf[2]&0x7f;
dispbuf[4]=dispbuf[4]&0x7f;
}
}
}
if(idot==2000)idot=0;
}
/*功能模块子函数*/
voidclockplus(void) /*时间加1s判断分,时子函数*/
{
if(++clock.s==60) /*秒位判断*/
{
clock.s=0;
if(++clock.m==60) /*分位判断*/
{
clock.m=0;
if(++clock.h==24) /*时位判断*/
{
clock.h=0;
if(++date.day==(getmonthdays(date.year,date.month)+1))
{
date.day=1;
if(++date.month==13)date.month=1;
}
}
}
}
}
voidtimerplus() /*秒表1/100秒位加1,判断秒、分子程序*/
{
if(++timer.ms==100)
{
timer.ms=0;
if(++timer.s==60)
{
timer.s=0;
if(++timer.m==60)
{
timer.m=0;
}
}
}
}
voidupdate_clockstr(void) /*更新时钟显示代码数组clockstr*/
{
clockstr[0]=led[clock.s%10]; /*给元素0赋相应数码管显示编码,编码序号是秒数的个位*/
clockstr[1]=led[(int)(clock.s/10)]; /*给元素1赋相应数码管显示编码,编码序号是秒数的十位*/
clockstr[2]=led[clock.m%10]; /*以下类推*/
clockstr[3]=led[(int)(clock.m/10)];
clockstr[4]=led[clock.h%10];
clockstr[5]=led[(int)(clock.h/10)];
}
voidupdate_alartstr(void) /*更新闹钟显示代码数组alartstr*/
{ /*右边两位显示on:
闹钟开启 of:
闹钟关闭*/
if(Alart_EN)alartstr[0]=ledchar[1];/*显示字母n*/
elsealartstr[0]=ledchar[2]; /*显示字母f*/
alartstr[1]=ledchar[0]; /*显示字母o*/
alartstr[2]=led[alart.m%10];
alartstr[3]=led[(int)(alart.m/10)];
alartstr[4]=led[alart.h%10];
alartstr[5]=led[(int)(alart.h/10)];
}
voidupdate_datestr(void) /*更新日期显示代码数组datestr*/
{
datestr[0]=led[date.day%10];
datestr[1]=led[(int)(date.day/10)];
datestr[2]=led[date.month%10];
datestr[3]=led[(int)(date.month/10)];
datestr[4]=led[date.year%10];
datestr[5]=led[(int)(date.year/10)];
}
voidupdate_timerstr(void) /*更新秒表显示代码数组timerstr*/
{
timerstr[0]=led[timer.ms%10];
timerstr[1]=led[(int)(timer.ms/10)];
timerstr[2]=led[timer.s%10];
timerstr[3]=led[(int)(timer.s/10)];
timerstr[4]=led[timer.m%10];
timerstr[5]=led[(int)(timer.m/10)];
}
voiddisplay(void) /*刷新显示六位LED一次*/
{
unsignedchari;
for(i=0;i<6;i++)
{
LED_ON(i); /*选通相应位*/
XBYTE[LED_SEG]=dispbuf[i]; /*写显示段码*/
deley(50); /*延时显示*/
LED_OFF; /*写LED全灭段码*/
}
}
voidupdate_dispbuf(unsignedchar*str) /*更新显示缓冲区子函数,参数为要用来更新缓冲区的源字符数组的首地址*/
{
dispbuf[0]=str[0]; /*将要更新的源字符数组内容COPY至dispbuf数组,用作显示缓冲区*/
dispbuf[1]=str[1];
dispbuf[2]=str[2]|0x80;/*默认把时位和分位后面的小数点显示出来,根据需要再取舍*/
dispbuf[3]=str[3];
dispbuf[4]=str[4]|0x80;
dispbuf[5]=str[5];
}
voiddeley(inti) /*延时子函数*/
{
while(i--);
}
unsignedchargetkeycode(void) /*键盘扫描子程序,返回获得的键码*/
{
unsignedcharkeycode; /*键码变量,一开始存行码*/
unsignedcharscancode=0x