赛多利斯酸度计使用说明书翻译.docx
《赛多利斯酸度计使用说明书翻译.docx》由会员分享,可在线阅读,更多相关《赛多利斯酸度计使用说明书翻译.docx(19页珍藏版)》请在冰豆网上搜索。
赛多利斯酸度计使用说明书翻译
LCD(液晶显示)
Singlechanneldisplay(单通道显示)
Note:
Notallofthefollowingwillbedisplayedatthesametime.
【注解:
以下符号并不会同时显示。
】
ⒶResult:
currentmeasurement.
【结果:
当前测量法。
】
ⒷUnits:
displaystheuntisforthecurrentmeasurement.
Examples:
pH,mV,mg/LF-,μS/cmorΩ·cm.
【单位:
显示当前测量值的单位。
例如:
pH,mV,mg/LF-,μS/cmorΩ·cm。
】
ⒸSoftkeyicons:
showthecurrentfunctionassignedtoeachsoftkey.
【软键图标:
显示指定的各软键的功能。
】
ⒹCalibrationduereminder:
the
iconremindsyouacalibrationisnowdue.
【校准到期提醒:
图标提醒校准现已到期。
】
ⒺDateandtime:
displayableindifferentformats.
【日期和时间:
可显示不同的格式。
】
ⒻDatalogging:
theicon
indicatesdataloggingisactive.
【数据记录:
图标
表示数据记录是激活的。
】
ⒼBuffers/Standards:
insinglechannelmode,allenteredbuffersorstandardsaredisplayed.A”!
”symbolnexttoabufferindicatesthatthebufferisoutoftheenteredcalibrationvalidtime(SeeCalibrationreminder,page21).
【缓冲液校准:
在单通道模式下,所有数据均显示校准值。
在“!
”符号旁边区域输入校准有效时间(见校准提醒,第21页)】
ⒽTemperature:
displaysthemeasuredtemperaturewhenanelectrodewithATCoraseparatetemperatureprobeisattached.Shows“M”whenamanuallyenteredtemperatureisbeingused.
【温度:
当电极与ATC或一个独立的温度探头连接时显示测量温度。
当手动输入温度时,显示“M”。
】
ⒾAlarm:
“
”indicatormeansdataisoutsidethesetalarmlimits.
【报警:
指示数据超出了设定的报警限值。
】
ⒿChannel:
indicateswhichelectrodechannel(input)isbeingdisplayed.ChannelsAεtBareBNCelectrodeinputs,andChannelCisaconductivitycellinput.
【通道:
表示正在显示的电极通道(输入)。
通道A和B是BNC接头电极输入,通道C是导电单元输入。
】
ⓀStability:
the
indicatestheelectrodeisstabletotheselectedcriteria.
【稳定性:
表明在选择的条件下,电极是稳定的。
】
Multiple-channeldisplay(多通道显示)
ⓁMultiple-Channel:
displaycanshowone(modelPP-15),two(modelPP-20andPP-25)ortheree(modelPP-50)electrodemeasurementswithtemperaturesimultaneously.
【多通道:
显示器可以显示一个通道(PP-15型),两个通道(PP-20型和PP-25型)或三个通道(PP-50型),电极测量与温度测量同时进行。
】
ⓂOut-of-rangeornon-validreading:
dashesindicatethatameasurementisnotavailable.
Thisusuallymeansthat:
-thereadingisoutofrange,or
-nostandardshavebeenenteredinionmode,or
-strictcalibrationhasbeensetandthecalibrationhasexpired.
【超范围的或无效的读数:
虚线表明这个测量是无效的。
这通常意味着:
读数超范围,或者在离子模式下没有校准,或者设置了严格校准模式并且校准已经过期。
】
FunctionKeys(功能键)
Mode:
selectsthemode:
pH,mV(ModelPP-15),lon(ModelsPP-25andPP-50),Conductivity–Resistivity–NaClSalinity–PracyicalSalinity–TDS(ModelsPP-20andPP-50)touseforthecurrentlyselectedchannel.
【模式键:
选择模式:
pH值,毫伏(PP-15型),LON(PP-25和PP-50型),电导率-电阻-氯化钠盐度-Pracyical盐度-TDS技术(PP-20和PP-50型)使用目前选定的通道。
】
Standardize:
entersbuffersorstandardsforthecurrentlyselectedchannel.UsetoenterpHbuffers,mVoffset,ionstandardsorconductivity/resistivitystandards.Alsousedtochangeothersettingswhichaffectthemeasurement.
【标准化:
在当前选定的通道进入缓冲液或标准液。
用于进入pH缓冲液,mV补偿,离子标准液或电导率/电阻率的标准液。
也可用于改变那些影响测量的其他设置。
】
CalData:
displaysandgraphsbuffersorstandardswithtimeanddatestampandelectrodecalibrationdatafortheselectedchannelandmode.
【校准数据:
在选定的通道和模式下图示用缓冲液或标准液进行的电极校准数据,并且带有时间和日期标识。
】
Channel:
selectsthechannel(s)(electrodeinputs)todisplay.ModelPP-15candisplayonechannel(ChannelA).TheModelPP-20candisplaytwochannels(ChannelsAandC).ModelPP-25canalsodisplaytwochannels(ChannelAandB).TheModelPP-50candisplayuptothreechannelssimultaneously(ChannelsA,BandC).
【通道:
选择显示测量电极的通道。
PP-15型,可以显示一个通道(通道A)。
PP-20型,可以显示两个通道(通道A和C)。
PP-25型也可以显示两个通道(通道A和B)。
PP-50型最多可以同时显示三个通道(通道A,B和C)。
】
Setup:
theSetupmenuisusedtosetvariousgeneralmetersettings,suchasdateandtime,displaycontrastandserialportconfiguration.
【设置:
设置菜单用来设置仪表的各种普通参数,如日期和时间,显示屏的对比度和串行端口的配置。
】
DataLog:
displaythedataloggingmenuusedtosetdataloggingandviewthestoredDataLog(seeDataLogging).
【数据记录:
显示参数设置的数据记录和查看存储的数据记录(见数据记录)。
】
Clear:
exitsthecurrentmenuandreturnstothepreviousmenu,cancelsthecurrentoperationorclearsanumberentry.
【清除:
退出当前菜单并且返回到上一级菜单,取消当前操作或清除输入的一个数字。
】
Enter/Print:
acceptsnumericvalues,menuselectionsorpendingoperations.Inthemainmeasurescreen,itactsasaPrintkey,andstoresthemeasurementsintheDataLog.Allcurrentmeasurementsaresenttoaprinter/computerthroughtheserialport.
【输入/打印:
接受数值,菜单选择或挂起的操作。
在多数测量界面上,它作为打印键,并存储测量结果到数据记录上。
所有的当前测量值通过串行端口被传输到打印机或者电脑上。
】
Softkeys:
thesefourkeysaccessdifferentoperationsatdifferenttimes.Mostmenusoffera“Help”softkeyandthe“Measure”softkey,whichallowsadirectreturntothemainmeasuringscreen,exitingallmenusimmediately.The“UpArrow”and“DownArrow”softkeysofferonewaytoselectamenuitem.The“LeftArrow”keyisabackspace,whichisactiveduringnumberentry.
【软键:
这四个键在不同的时间执行不同的操作。
大多数菜单下提供“帮助”软键和“测量”软键,“测量”软键允许直接返回到主测量界面,立即退出所有菜单。
“向上箭头”和“向下箭头”软键用来选择一个菜单项。
“左箭头”键是退格,在输入数字时有效。
】
NumericKeys:
pressinganumberkeyselectsanumberediteminamenu.Thenumberkeysalsoallowenteringvaluesforbuffersolutions,standards,andvariousmetersettings.
【数字键:
按下一个数字键,在菜单中选择编号项目。
数字键也可以输入缓冲液、标准液和不同的仪表设置参数。
】
Softkeys(软键)
Help(帮助)
Measure(测量)
Scrollup(向上滚动)
Scrolldown(向下滚动)
Backspace(退格)
Graph(图表)
Exponentnumberentry(指数数字输入)
Incrementalionmethod(增量离子法)
Presssoftkey:
startsmeasurement(按软键:
开始测量)
Measurelock:
eachdisplayreadingwillfreezewhenstable(测量锁:
每个显示稳定的读数将被冻结)
Measurementisperformed(进行测量)
Channels(通道)
TheChannelkeyisusedtoturnonoroffeachavailablechannel.Insingle-channeloperation,additionalinformationisprovidedfortheselectedchannel,includingalistofallenteredbuffersorstandards.Inmulti-channeloperation,theMode,StandardizeandCalDatamenusaskforthechannelbeforeaccessingthemenu.
【通道键用于打开或关闭每个可用的通道。
单通道操作时,提供了选定通道的所有缓冲液或校准液的信息清单。
多通道操作时,在访问菜单前,模式、标准化和校准数据按键要选择通道。
】
ModelPP-15:
(PP-15型)
Offerssingle-channeloperation(pHandORPelectrodes).
【提供单通道操作(pH和ORP电极)。
】
UsingandStoringElectrodes(使用和保存电极)
pHGlassElectrodes(pH玻璃电极)
●Providemoderatestirringforfasterelectroderesponse.
【进行温和的搅拌可以使电极更快的响应。
】
●Leavethefillholeopenduringalluse.
【使用时取下保存盖。
】
●Rinsetheelectrodebetweeneachmeasurementwithaportionofthenextsampleorbuffertobemeasured,orwithdeionizedordistilledwater.
【在每次测量之间均需要冲洗电极,使用部分待测样品或缓冲液,或者使用去离子水或蒸馏水。
】
●Keepglasselectrodeswetwhennotbeingusedbyplacingsomeelectrodefillingsolutioninthewettingcapandstoringwiththewettingcapon.
【不使用时要保持玻璃电极湿润,在湿润帽里装一些电极填充液并将电极储存在湿润帽里。
】
●Keepingglasselectrodes“wet”willimprovetheirperformance.Storeelectrodesinelectrodefillingsolutionorstoragesolution(KCl,3mol/L).
【保持玻璃电极“湿润”将提高其性能。
需将极保存在电极填充溶液或保存溶液中(3mol/L氯化钾)。
】
MeterSetup(仪表设置)
MeterSetupMenu
【仪表设置菜单】
PressSetuptoaccesstheMeterSetupmenu:
【按“Setup”访问仪表设置菜单:
】
1.Timeanddatamenu:
usetosetthetimeformat(HH:
MM:
SSorHH:
MM:
AM/PM),thetime,thedateformat(MM/DD/YYYY,DD-MM-YYYYorYYYY.MM.DD),andthedate.
【时间和日期菜单:
用于设置时间格式(时:
分:
秒或时:
分:
上午/下午),和日期格式(月/日/年,日-月-年或年.月.日)。
】
2.Selecttemperatureunits:
usetoselecttemperaturemeasurementanddisplayinCelsius,FahrenheitorKelvin.
【选择温度单位:
用于选择温度测量时显示的单位:
摄氏,华氏或开尔文温度。
】
3.Selectcontrast:
usetoselectthedisplaycontrast,makingthedisplayedcharacterslighterordarker.Selectsetting“5”fortypicalconditions.
【选择对比度:
用于选择显示器的对比度,使显示的字符更亮或者更暗。
标准设置为“5”。
】
4.Selectlanguage:
usetoselectthedesireduserlanguage.
【选择语言:
用于选择用户所需的语言。
】
5.Setupserialport:
usetoconfiguretheserialportstartbits,baudrateandparitysetting.Thismustmatchthesettingoftheprinterorcomputerbeingusedwiththemeter.
【设置串行端口:
用于配置串口的起始位,波特率和奇偶校验位设置。
这必须符合正在使用的仪表的打印机或计算机设置。
】
6.Keypressbeep:
ThismenuitemturnsthekeypressbeepONandOFF.
【按键提示音:
这个菜单项转换按键提示音为ON或OFF。
】
7.Selectdisplaybackground:
usetosetthedisplaytoblackcharactersonawhitebackgroundorwhitecharactersonablackbackground.
【选择显示器背景:
用于设置在白色背景上显示黑字或者在黑色背景上显示白字。
】
8.Showmeterinformation:
usetoshowthemetermodel,softwareversionandserialnumber.
【显示仪表信息:
用于显示仪器型号,软件版本和生产序列号。
】
9.Enablemeasurelock:
thisfeaturelocks(orfreezes)stablemeasurementsforlaterreview.StabilitycriteriashouldbesettoSLOWforallchannelsandmodesinuse(seeOptionsMenu).
【激活测量锁:
此功能锁定(或冻结)稳定的测量结果,便于稍后的查阅。
稳定的标准,对于所有使用的渠道和模式均应设置为慢速(见选项菜单)。
】
10.Enablestrictcalibration:
usetosetstrictcalibrationwherenomeasurementsaredisplayedifthecalibrationreminderhasexpired.
【启用严格的校准:
使用设置严格的校准:
如果校准提醒已过期,将不显示测量值。
】
“±”Setscreensaver:
usetoactivatethescreensaver.
【“±”设置屏幕保护程序:
使用激活屏幕保护程序。
】
“·”Restorefactorydefaults:
usetoresetallsettingstofactorydefaults.Onoccasion,itmaybeusefultocompletelyresetthemeter,forexample,ifotherusershavechangedasetting.
【“·”恢复出厂默认设置:
使所有设置重置为出厂默认值。
某些时候,它可能用于完全复位仪表。
例如,如果其他用户改变了设置。
】
Warning!
Aresetalsoclearsallelectrodestandardizations.
【警告!
复位会清除所有电极标准化。
】
pHMode(pH模式)
pHModeStandardizationMenu
【PH模式标准化菜单】
PressModeandselect1)pH.
【按模式按钮并选择1)pH值。
】
PressStandardizeandthepHModeStandardizeMenuappears:
【按标准化按钮则pH模式下的标准化菜单显示:
】
1.Auto-enterabuffer:
usetoaddanewbufferwhichisauto-recognizedbythemeter,orupdateanexistingbuffer.Followtheprompts.
【自动检测缓冲液:
添加缓冲液或检测新的缓冲液时仪表会自动确认。
按照提示进行操作。
】
2.Manualbufferentry:
usetoenterabuffervaluebymanuallyenteringthepHofthebuffer.
【手工输入校准液值:
手工输入校准液的pH值。
】
3.Clearbuffers:
usetoclearallbuffersenteredforthecurrentchannel(pHmode).Ifallenteredbuffersarebeingre-entered,itisusuallynotnecessarytoclearbuffersbeforere-enteringthem.
【清除校准液值:
用于清除当前通道(pH模式)的所有校准液值。
如果全部的校准液都要重新检测,通常没有必要在检测前清除校准液值。
】
4.OptionsMenu:
usetodefineadditionalspecificpHmodesettingse.g.tosetpHlimits.(Seepage23).
【选项菜单:
使用定义其他特殊的pH值模式设置,例如,设置pH值限值。
(见第23页)。
】