轴承清洁度检测规程.docx
《轴承清洁度检测规程.docx》由会员分享,可在线阅读,更多相关《轴承清洁度检测规程.docx(16页珍藏版)》请在冰豆网上搜索。
轴承清洁度检测规程
Documenteditinformation文件修订信息
VersionNo.
版本号
Modificationreason&content
修改原因/内容
EditDate
修订日期
EditPerson
修订人
Remark
备注
B
27-WI-103-F03表格换版
2013-01-18
张仪君
C
增加各尺寸的清洁度检测方法及判定标准等
2014/11/05
张仪君
Review审核
Correlativedepartment
相关部门
Reviewopinion
评审意见
Reviewperson/Date
评审人/日期
Approval批准
Department
部门
Opinion
评审意见
Approvalperson/Date
批准人/日期
MR
(limittoprocedureonly)
管理者代表
(仅限于程序文件)
DepartmentManager
部门经理
OK
汪洋
1Purpose目的
为规范成品轴承装配后的清洁度检测操作程序。
Toregulatetheassemblyoffinishedbearingafterthedirtcounttestprocedures.
2Scope使用范围
本规程适用于成品轴承涂油包装后的清洁度检测。
Theprocedureappliedtobearingsdirtcounttestingafterpackaging.
3Responsibility职责
工流体实验室负责各单元的清洁度检测工作。
Fluidslabisresponsiblefordirtcounttest..
4Definition术语(无)
5Procedures过程及要求
(浸没法)方法适用于外径0到12英寸的轴承和零部件,检测频次及数量参照附录1。
(DipMethod)Testforcontaminantcontentof0to12inchODbearingcomponents,testfrequencyandquantityperaddendum1.
仪器设备Apparatus
5.1.1.1微孔耐热玻璃支架(xx1004720)
Milliporepyrexfilterholderxx1004720
5.1.1.2标准微孔滤膜微米孔隙HAWP0470020
StandardMilliporemicrometerporesizeHAWP04700
5.1.1.3微孔玻璃密封装置,显示屏和制动器xx10047032
Milliporeglasssealbase,screen,andstopperxx10047032
1-2L规格的弯臂抽气瓶(1公升微孔xx1004705)
Oneortwolitersidearmfilterflasks(Milliporeoneliterxx1004705)
5.1.1.4塑料管Plastictubing
5.1.1.5防爆炸真空泵(适当的防止粉碎就可以)。
VacuumpumpFisherScientific
5.1.1.6塑料洗瓶PlasticWashbottle
5.1.1.7不锈钢容器或玻璃烧杯(必须足够大,可让部件平放到容器底部,并与容器有一定间隙)。
Stainlesscontainerorglassbeaker(mustbelargeenoughtoallowcomponentstolayflatonbottomwithroomtospare)
5.1.1.8不锈钢镊子Stainlesssteelforceps
5.1.1.9干燥箱Dryingoven
5.1.1.10分析天平(0.0001g灵敏度。
)
Analyticalbalancecapableofweighingto0.0001g
5.1.1.11通风柜Ventilationhood
5.1.2清洗溶剂WashingSolvent
闪点大于60度的石蜡基溶剂,如ShellsolD60;LPA142;Ashlandsol142等
注意:
危险物极其易燃,水蒸气也可能引起火花。
远离热源,火花,和明火。
在足够的通风和有通风橱的情况下使用。
NOTE:
Extremelyflammable,Vaporcauseflashfire,Keepawayfromheatsparksandopenflame.Usewithadequateventilationandinhood.
操作程序Procedure
测量残磁≤2高斯,预称重滤膜,并用圆珠笔或铅笔在每个滤膜上标出识别编号。
Measureresidualmagnetism≤2gauss,pre-weighingfilter,markanidentificationnumberoneachfilterwithapencilorballpointpen.
对试验滤膜进行称重并记录重量,精确到。
Weighfilterstothenearestandrecordweigh.
为每个试验滤膜配置一个额外的滤膜,并称重每个控制滤膜。
(在进行过滤前,这个控制滤膜将直接插入到试验滤膜下。
上膜为试验滤膜,下膜为控制滤膜)
Weighanextrafilterforeachtestfilter.(Thiscontrolfilterisinserteddirectlybeneaththetestfilterpriortothefiltrationprocedure)
注意:
在操作整个过程中,用镊子操纵过滤器。
NOTE:
Handlefilterswithforcepsatalltimes.
清洗轴承部件Cleaningofbearingcomponents
在清洗容器中倒入足够的溶剂,使一个轴承部件完全浸入溶剂中。
清洗容器首选玻璃烧杯,但对大尺寸轴承,需要用不锈钢杯或盘。
Pureintothewashingcontainerenoughsolvent,completelycoveronebearingcomponent.Glassbeakersarepreferredbutstainlessbeakersortraysareneededforlargersizebearing.
5.3.2在充分搅动中清洗轴承部件15秒,以便有效去除微粒和防腐剂。
对装配后的内圈,为充分去除所有微粒和防腐剂,必须转动部件或溶液至少15秒。
Washbearingcomponentsfor15secondstoremoveparticlesandpreservative.Forassembledcones,rotatingthecomponentsinthesolventtoremoveparticlesandpreservative.
从溶剂中取出轴承,然后用溶剂喷雾剂彻底喷洒至少10秒钟。
在此期间,应边清洗边让冲洗物流入容器。
对组装后的轴承应边转动边清洗。
分开清洗每一个部件,然后立即干燥。
最后用防锈材料如QuakerFERROCOTE5856BFT1将轴承重新防护。
Removethebearingfromthesolventandwashthoroughlywithafinesprayofhexanefromthewashbottleforatleast10seconds.Duringthisstep,allwashingshoulddrainintothecontainer.Coneassembliesshouldberotated.Washeachcomponentandthenimmediatelydry.preservethebearingwithQuakerFERROCOTE5856BFT1
注意:
轴承部件用一个过滤盘。
由于溶剂烟雾是危险的,所以整个清洗过程必须在实验室环境下进行。
不可接触皮肤。
在整个操作过程中,可使用钳子或塑料手套处理轴承部件。
但只有(经过含污量)证实的防尘手套可使用(聚乙烯手套)。
避免使用已破损,有斑点的手套。
NOTE:
Useonefilterdiskforfivebearings.Thecleaningproceduremustbeinthelabhoodsincethesolventfumesishazardous.Usetongsorplasticglovestocleanthebearingcomponent.Onlyglovesproventobefreeofdirt(suchasPEgloves)canbeused
过滤清洗后溶液Filteringwashingsolvent
将事先已称重的微米孔隙的滤膜,安放于微孔过滤器上。
(上膜)
AssembleMilliporefilterwithapre-weighedfilter.(topfilter)
在实验滤膜下放置一张事先已称重的控制滤膜。
(下膜)
Insertapre-weighedcontrolfilterbeneaththetestfilter.(bottomfilter)
小心的将清洗后溶液倒入过滤漏斗,并用装有真空抽气装置的抽气瓶将溶液通过滤膜真空过滤。
Pourthesolventintothefilterfunnelcarefullyandapplyvacuumtodrawthesolventthroughthefilter.
所有的溶剂过滤后,用装有溶剂的洗瓶喷洗容器四次,以便将容器残留的微粒洗掉。
然后喷洗过滤漏斗壁,确保滤液的所有的微粒已收集,所有的防腐剂或残油已完全收集。
再移开固定装置,喷洗漏斗和装置结合处,清洗出任何遗留在那里的残油。
重新清洗漏斗后再卸下。
Afterfilteredallsolvent,washthecontainerfourtimeswithawashbottletoremoveparticles.Thenwashthewallsoffilterfunnel.Removeclampandsprayoutsideofthefunnel-basejunctiontodrawinanyoilcollectedthere.Rewashfunnelanddisassemble.
释放真空后,用镊子移动滤膜盘,放置到干净平整的纸上晾干。
Afterreleasingvacuum,useforcepstoremovethefilterdisks.Placethemonasheetofflatpaperfordrying.
重新称重Reweighing
将滤膜放置在干燥箱中干燥15分钟,干燥温度为80-100℃(175-212℉)。
Placethefiltersinaovenat80-100℃(175-212℉)anddryfor15minutes.
从干燥箱中取出滤膜并冷却15分钟。
Removefromtheovenandletthefiltercool15minutes。
重新称重滤膜,精确到。
Reweighthefilterstothenearest.
计算Calculation
用最终的测试滤膜重量,减去初始滤膜的重量。
可减去控制滤膜增加重量或加上控制滤膜失去的重量,以修正每次的测试结果。
用合成的总含污量除以参与试验的总部件数,就可得到每个部件的平均含污量。
(如果用足够的洗液去除残油的话,控制滤膜增加的重量不应该超过)
Subtracttheinitialweighofthetestfilterfromthefinaltestfilterweight.Thensubtractweightgainoraddweighlossofcontrolfilterasacorrectionfactorforeachtestresult.Dividetheresultanttotaldirtcountbythenumberofcomponentsusedinthetesttoobtaintheaveragedirtcontentofeachcomponent.(Theweightincreaseofthecontrolfiltershouldnotexceedifadequatewashingisusedtoremoveoilresidue)
表面积的数据可从27-WI-103-F02“成品轴承表面积一览表”查得。
评判标准(参见附录1)Limits(Refertoaddendum1)
总重量TotalWeight
颗粒物尺寸/类别Particlesize/type
相关措施CorrectiveAction
若测试轴承的含污量超过允许值,工艺流体及防锈实验室应立即通知车间对相关产品进行处置,并分析原因,针对原因制定并实施纠正措施,工艺流体及防锈实验室对实施效果进行验证。
纠正措施还可包括:
过程流程调查,对滤膜,油槽含污量,与过程流程和滤膜相关的维护准则、操作程序回顾。
车间应将更换、及相应的一些措施记录于27-WI-103-F03“清洗液/防锈油/过滤系统更换记录”。
Whenbearingstestedcontainmorecontaminantorparticlesthanthemaximumallowable,appropriatecorrectiveactionsmustbeinitiated.Theseincludebutarenotlimitedto:
aphysicalinvestigationofprocessfluids,filters,contaminantcontentinreservoirs,areviewofthemaintenancepracticesrelatedtoprocessfluidsandfilters,areviewofhandlingprocedures,andanyotherappropriateproblemsolvingactivitiesaimedatproducingbearingsfreefromcontaminants.Workshopshouldbereplaced,andthecorrespondingmeasuresrecordedinthe27-WI-103-F03"cleaningfluid/RPoil/filtersystemreplacementrecord."
注意:
用塑料桶收集废液。
在桶上贴上危险物和易燃标签。
将所有的桶送到EHS指定的地点。
Note:
Drumupwastesolventinplasticdrums.Hazardouswasteandflammablelabelsmustbeondrums.Sendfulldrumstotheappropriateoff-sitedisposalfacility.
▲(吊索压力喷淋法)方法适用于外径12到18英寸的轴承和零部件,检测频次及数量参照附录1。
(Sling/PressureSprayMethod)Testforcontaminantlevelof12to18inchbearingcomponents.Testfrequencyandquantityperaddendum1.
仪器设备Apparatus
参照注意:
滤膜是带网格的标准微孔滤膜,型号:
SVWG04700)
Seesection(Noteexception:
griddedfilterSVWG04700)
喷射容器罐型号:
XX6700P05MilliporePressureVesselmodel#XX6700P05
溶剂喷雾枪型号:
XX6702500MilliporeFilterjetSolventDispenserwithfanspraynozzlemodel#XX6702500.
清洗溶剂WashingSolvent
闪点大于60度的石蜡基溶剂,如ShellsolD60;LPA142;Ashlandsol142等
注意:
危险物极其易燃,水蒸气也可能引起火花。
远离热源,火花,和明火。
在足够的通风和有通风橱的情况下使用。
NOTE:
Extremelyflammable,Vaporcauseflashfire,Keepawayfromheatsparksandopenflame.Usewithadequateventilationandinhood.
操作程序Procedure
测量残磁,将零部件放在合适的容器内以便收集清洗后的溶剂,对于重量或是尺寸过大的零件必须要使用行车。
Measureresidualmagnetism;placethepartsin/overanappropriatelysizedcollectionvesselsuchthatallthesolventwillbecollected.Itmaybenecessarytohangthepartfromacraneduetoitsweightandsize.
调节容器喷淋口的压力在15psig±5psig。
Pressurizethesprayvesseltoapressure.Arecommendedvalueis15psig±5psig.
将零部件放在收集容器内开始喷淋清洗,每个零部件喷淋清洗5~10秒,之后重复3次。
注意喷淋清洗过程中的压力要保持在15psig±5psig。
Placethepartinto/overthecollectionvessel,Agoodruleofthumbistogivetheareaofthepart5to10secondsofspray.Repeateachspray3times.Beawareofthesprayerpressure.Thepressureofthevesselshouldbemaintainedattherecommendedvalueof15psig±5psig.
将零部件移出,让溶剂残留回到收集容器内,再翻个身以收集尽量多的溶剂。
如果有必要,将零部件悬空以收集所有的溶剂
Removethepartandlettheresidualfluiddrainbackintothecollectionvessel.Turntheparttomakesureasmuchofthefluidaspossibleiscollected.Ifnecessary,suspendthepartoverthecollectionvesselbysomemethoduntilallofthesolventiscollected.
按照的步骤,用μm滤纸过滤收集的溶剂,用干净的溶剂漂洗收集容器、微孔过滤玻璃支架。
所有用来漂洗清洁度设备的溶剂必须经过μm的滤纸过滤。
FilterthecollectedsolventthroughagriddedμmfilterpreparedasperparagraphRinseoutthecollectionvesselwithcleansolvent.Rinsedownthefilterholder.Allsolventusedforrinsingtheequipmentmustbefilteredthroughafilter.
用镊子移动滤膜盘,放置到干净平整的纸上晾干。
Useforcepstoremovethefilterdisks.Placethemonasheetofflatpaperfordrying.
重新称重Reweighing
将滤膜放置在干燥箱中干燥15分钟,干燥温度为80-100℃(175-212℉)。
Placethefiltersinaovenat80-100℃(175-212℉)anddryfor15minutes.
从干燥箱中取出滤膜并冷却15分钟。
Removefromtheovenandletthefiltercool15minutes。
重新称重滤膜,精确到。
Reweighthefilterstothenearest.
计算Calculation
用最终的测试滤膜重量,减去初始滤膜的重量。
可减去控制滤膜增加重量或加上控制滤膜失去的重量,以修正每次的测试结果。
用合成的总含污量除以参与试验的总部件数,就可得到每个部件的平均含污量。
(如果用足够的洗液去除残油的话,控制滤膜增加的重量不应该超过)
Subtracttheinitialweighofthetestfilterfromthefinaltestfilterweight.Thensubtractweightgainoraddweighlossofcontrolfilterasacorrectionfactorforeachtestresult.Dividetheresultanttotaldirtcountb