UOP规范往复式压缩机Word文件下载.docx
《UOP规范往复式压缩机Word文件下载.docx》由会员分享,可在线阅读,更多相关《UOP规范往复式压缩机Word文件下载.docx(11页珍藏版)》请在冰豆网上搜索。
c.ASMEB16.47,“LargeDiameterSteelFlanges,NPS26ThroughNPS60”
d.ASMEB46.1,“SurfaceTexture(SurfaceRoughness,Waviness,andLay)”
e.EuropeanForumforReciprocatingCompressors(EFRC),“GuidelinesforVibrationsinReciprocatingCompressorSystems”,www.recip.org
f.National,state,andlocalgovernmentalregulationsandlaws.
a.API618标准石油化工和天然气工业用往复式压缩机
b.美国机械工程师学会(ASME)B16.5,“管法兰和法兰管件,NPS1/2至NPS24公制/英制标准”。
c.ASMEB16.47大直径管钢制法兰(NPS26~NPS60)
d.ASMEB46.1,表面特征(表面粗糙度、波纹度和花纹方向).
e.欧洲的往复式压缩机论坛(EFRC),“往复式压缩机系统振动指南”,www.recip.org
f.国家、州和地方政府法律和规定。
2.DESIGN设计
ThisstandardisintendedtobeusedasanaddendumtoAPIStandard618.NumberinginthisdocumentcoincideswithactualparagraphnumbersfromAPIStandard6185thedition.
本标准用作API标准618的补充。
本章节中所采用的编号与API6185th版的实际段落编号相同。
ReciprocatingcompressorsshallcomplywiththerequirementsofAPIStandard618,exceptwheremodifiedbyeithertheUOPProjectSpecification(s)orUOPStandardSpecification(s).
压缩机应遵守API618的要求,“UOP公司工程规范”或“UOP标准规范”中加以修改的部分除外。
5.Requirements要求
Paragraph5.2,Addition/Clarification增加/澄清
Vendor’sofferingshallbeasizeanddesignwhichhasasuccessfulrecordofprovenfieldserviceatoperatingconditionssimilartothosespecified(prototypesarenotacceptable).Aninstallationlistshallbesubmitteduponrequest.
供货商报价中的规格和设计应具有在规定操作条件下现场成功应用的验证记录(不接受样机)。
如果有要求,应提交业绩表。
6.BasicDesign基础设计
6.1General概要
Paragraph6.1.24,Clarification澄清
Thecompressorshallbecapableofcontinuousoperationatallpartialloadsteps.(0%loadstepisforshorttermstartuponly).
压缩机应能在部分加载过程中连续操作(0%加载仅供短期启动)
CompressorvendorshallprovidePLC,andPLCshallincludecontrollogictoensureunloadingofbothpartiallyandfullyunloadedcylindersfollowsbestpracticesestablishedbelow:
压缩机供应商应提供PLC,PLC应该包括控制逻辑单元来确保气缸部分或完全卸载时采用如下最佳方案表
情况
最佳方案
部分卸载
周期性,短暂的载入气缸头空载来阻止润滑油积聚对机器造成的损害
完全卸载
仅对多级气缸并联操作状况下,加载卸载定期切换来阻止热量或润滑油积聚对机器的损害
Manufacturertostatefrequencyanddurationofrequiredloadingtoachieveaboveobjectivesinproposal.
未达到以上目标,制造商需提出加载频率和持续时间
6.6RodandGasLoads活塞杆负荷和气体负荷
Paragraph6.6.1,Addition/Clarification增加/澄清
Frameselectionshallbebasedonthemoreconservativeofthefollowingcriteria:
框架选择应基于以下标准中较为保守的部分:
-Combinedrodloadingshallnotexceed80%ofthemanufacturer’sMaximumAllowableContinuousCombinedRodLoading(MACCRL)whencalculatedatspecifiedlinepressuresofeachstage.
当计算在每个阶段的管线压力时,活塞杆负荷不超过制造商最大允许负荷(MACCRL)的80%。
-Combinedrodloadingshallnotexceed95%ofthemanufacturer’sMaximumAllowableContinuousCombinedRodLoading(MACCRL)whencalculatedasdefinedinparagraph6.6.1.
当按第6.6.1条计算时,活塞杆负荷不应超过制造商最大允许活塞杆负荷(MACCRL)的95%。
6.8CompressorCylinders压缩机气缸
Paragraph6.8.1,Addition增加
Themaximumcylinderdiameteris36inches(914mm).ExceptionsrequirewrittenapprovalfromUOP.1
最大气缸直径为36英尺(914mm)。
免责条款需要UOP批准。
Paragraph6.8.2.4,Addition/Clarification增加澄清
Whennon-metallicwearbandsandpistonringsareused,theinsidesurfaceoflinersshallbehonedperparagraph6.8.2.4.
当使用非金属支撑环和活塞环时,应按6.8.2.4章进行内表面打磨。
Paragraph6.8.4.2,Addition/Clarification增加澄清
FlangeclassesspecifiedareinaccordancewithASMEB16.5orASMEB16.47.
法兰等级按照ASMEB16.5或ASMEB16.47的规定。
FlangeclasseslistedintheUOPProjectSpecificationarebasedupondesignpressureandtemperatureconditionsonlyanddonotaccountforotherloads.Thefinaldesignofallflangesshallaccountforgasketseating,externalloadsimposedbypiping,andallotherimposedloads.Differentialthermalexpansionofdissimilarjointsandtransientthermalconditionssuchasstart-up/shutdownandoperationalupsetshallbeaccomodated.
在UOP项目规范中列出的法兰等级只基于设计压力和温度条件,不考虑其他负载。
所有法兰的最终设计应考虑到阀座、管道外荷载和所有其他荷载。
应适应如启动/关闭和切换时不同接头的热膨胀和瞬态热状态。
Flangesintendedforusewithspiralwoundgasketsshallhaveaflangesurfacefinishof125microinchRaminimumto250microinchRamaximum.Flangesintendedforusewithothergasketsshallhaveaflangesurfacefinishwithintheoptimalrangeforthespecifiedgasket.FinishesshallbejudgedbyvisualcomparisonwithsurfacefinishroughnessstandardsconformingtoASMEB46.1.
用螺旋缠绕垫圈的法兰盘表面粗糙度应介于125微英寸到250微英寸之间。
使用其他垫片的法兰盘的表面加工应符合垫片规范最佳值。
Flangefinishesshallbeprotectedfromdamageduringfabrication,heattreatment,shipping,storageandinstallation.
法兰盘成品应使用符合ASMEB46.1标准的表面粗糙度标准进行目视比较。
RingJointflangesshallhaveaflatbottomgroovewiththeintersectionbetweenthebottomandsidesofthegroovemachinedtoasmooth0.125inch(3mm)minimumradius.
槽式密封面法兰应该有一个平的底部沟槽,在凹槽的底部和侧面之间的光滑十字槽加工尺寸最小半径0.125英寸(3mm)。
6.9ValvesandUnloaders气阀和卸荷器
Paragraph6.9.2.6,Clarification澄清
Topreventfailureoftheunloadertoactuateduetocorrosion:
为防止因腐蚀造成的卸荷器失效
-Theunloaderactuatorsshallbeaweatherproofdesignwhichpreventsingressofwaterandothercontaminants.
卸荷器应采用防水密封设计防止水和其他污染物进入
-Allcriticalslidingfitcomponentsintheunloaderactuatorsshallbeconstructedofcorrosionresistantmaterials,including:
所有卸荷器关键滑动部件应采用耐腐蚀材料
oPistons/operators制动器/操作机构
oUnloaderCylinderbodies卸荷器缸体
oUnloaderShafts/spindles/pushrods卸荷器轴/主轴/推杆
Theactuators/operatorsshallbesizedfor10psi(0.7kg/cm²
)lessthanthespecifiedminimumsiteoperatingfluidpressure.Unloadersshallbeshoptestedforproperactuation
制动器\操作机构结构尺寸应该适合10psi(0.7kg/cm²
)小于规定最小现场流体压力。
卸荷器应进行适当的驱动工厂实验。
Paragraph6.9.2.7,Clarification澄清
Rainshieldsshallbeprovidedwithallmachines,unless:
所有机器均应提供防雨罩,除非:
-Installedindoors.室内安装
-ThevendorunloaderdesigncomplieswithUOPclarification6.9.2.6
供应商卸荷器完全采用UOP澄清6.9.2.6设计
6.10Pistons,PistonRods,andPistonRings活塞活塞杆活塞环
Paragraph6.10.3,Addition增加
Castaluminumandfabricatedsteelpistonsshallnotbeusedabove500horsepower(375kW)percylinder.铸铝和焊接钢活塞不应用于超过500马力(375kw)每气缸
Pistons,whenintegrated/integralwiththepistonrod(e.g.lowratiobetweenpistonroddiameterandcylinderdiameter)shallbeconstructedofthesamematerialasthepistonrodandmaybefabricatedwithoutlimitsabove.
当整体或与活塞杆一体活塞(如活塞杆直径和气缸直径比低)应采用活塞杆相同材质,不受上述限制。
Paragraph6.10.3.1,Clarification/Addition澄清\增加
Hollowsingle-piecepistonsshallhaveaspringloadedreliefplugintheouter-endfaceofthepiston.中空单体活塞应在活塞外端面安装一个弹簧安全阀
Multi-piecepistonsshallhaveaminimum1/8”(3mm)diameterdrilledventhole多体活塞应有一个最小直径1/8”(3mm)孔
6.12DistancePieces接筒
Paragraph6.12.2.1,Clarification澄清
Distancepiecesshallbeprovidedwithgasketed,solidmetalcovers.
接筒应提供带封圈固体金属盖板
Paragraph6.12.2.4,Addition增加
Compartmentsshallbeventedseparatelytonon-hazardousareas.
接筒腔室应与无害区域分隔排放
Paragraph6.12.2.7,Addition增加
Packingventpipinginsideofthedistancepieceshallbedesignedforthemaximumallowableworkingpressureofthecylinder.
取代接筒的内部填料放气管道设计时应考虑气缸最大工作压力
6.14.2CompressorFrameLubrication压缩机机身润滑
Paragraph6.14.2.1.4,Addition增加
Thereservoirshallbefittedwithalubeoiltemperaturetransmitter.
油箱应设有温度传感器
Paragraph6.14.2.2,Addition增加
Whenanauxiliaryoilpumpisnotprovided,ahandpumpshallbeprovidedforstart-uplubrication.如果没有辅机泵,为了开启润滑应提供手动泵
Paragraph6.14.2.3,Addition增加
Forapplicationswithratedpowersbelow250horsepower(185kW),oilcoolersarenotrequiredprovidedthevendorcandemonstratethroughcalculationandoperatingexperiencethattheframehasadequateradiativeareatodissipatetheheat.
当额定功率低于250马力(185kW)时,供应商无需提供油冷却器若能通过计算和操作经验证明框架有足够的辐射面积来散热。
Paragraph6.14.2.5,Clarification澄清
Heatingforreservoirsshallbeprovidedwhentheminimumambienttemperatureislessthanthevendor'
srequiredminimumstart-uptemperature.ThermostaticallycontrolledimmersionheatersconformingtoAPI618shallbeused.当最低环境温度低于供应商所需的最低启动温度时需要安装油箱加热器。
恒温控制加热器应符合API618标准
7.Accessories辅助设备
7.2CouplingsandGuards联轴器和防护罩
Paragraph7.2.1,Addition/Clarification增加\澄清
Couplingsshallallowcontinuousoperationwithtwicetheestimatedcold-tohotthermalgrowth.
联轴器应满足在两倍预估热膨胀条件下持续工作
7.6ControlsandInstrumentation控制和仪表
Paragraph7.6.1.2,Clarification澄清
Provideaseparatelymountedlocalinstrumentpanelforeachcompressor.Asaminimumthefollowingshallbeincluded:
-Processgasinletanddischargetemperaturesforeachcylinder
-Processgasinletanddischargepressuresforeachstage
-Framelubeoilpressure
-Speedforvariablespeeddrivers
-Multi-positionselectorswitchforcylinderloading(eachservice)
每台压缩机非别安装现场仪表,至少应包括如下:
每台气缸进出口气体温度传感器
各级压力传感器
机身润滑油压力
变频电机速度传感器
气缸加载多位选择开关(每次服务)
Paragraph7.6.2.4,Addition增加
Thesystemshallbecapableofstartingupandshuttingdownwitheachstageunloaded.控制系统应具有分级卸载开启关闭能力
InadditionthevendorshallalsodoONEofthefollowing:
此外供应商应做一下一项工作
-Provideinterlockstoensurethatthecompressorcann