加工中心精度检验规范文档格式.docx
《加工中心精度检验规范文档格式.docx》由会员分享,可在线阅读,更多相关《加工中心精度检验规范文档格式.docx(12页珍藏版)》请在冰豆网上搜索。
DATE
MCVF01S001
Q301000003940331-7
1.0静态精度STATICACCURACYINSPECTION单位Unit:
mm
项
次
NO
检查项目
Inspectionitem
测试方法图
Measuringmethoddiagram
许可差
Permissibledeviation
实际
测量值
Measuredvalue
1.1
床台X轴方向运动之真直度
StraightnessoftheXaxismovement
a.
X-Z
面内
0.06/1000
b.
Y-Z
1.2
床台Y轴方向运动之真直度
StraightnessoftheYaxismovement
1-1
单位Unit:
1.3
床台X轴方向之运动与其上面之平行度
ParallelismbetweenmovementinXaxisdirectionandtableuppersurface
X≦5000.02
500<X≦8000.025
800<X≦12500.03
1250<X≦20000.04
1.4
床台Y轴方向之运动与其上面之平行度
ParallelismbetweenmovementinYaxisdirectionandtableuppersurface
Y≦5000.02
500<Y≦8000.025
800<Y≦12500.03
1250<Y≦20000.04
1.5
X轴方向运动与床台基准沟侧面之平行度
ParallelismbetweenmovementinXaxisdirectionandSidesurfaceoftablereferenceslot
每300mm的量测距离下
许可差为0.015mm
0.015forameasuring
lengthof300
1-2
单位Unit:
1.6
各轴方向相互运动之直角度
PerpendicularityBetweenmovementinXaxisdirectionandYaxisdirectionandZaxisdirection
X-Y
轴Place
0.012/300
c.
1.7
主轴中心线与床台面之直角度
Perpendicularitybetweencenterlineofmainspindleandtablesurface.
旋径每300
Per300
0.015
1-3
1.8
主轴孔内面之偏摆
Runoutofspindletaperhole
固定端
Atspindlesideendoftestbar
0.005
固定端300处
At300position
1.9
主轴轴线与Z轴轴线运动间的平行度
Parallelismbetweenthespindleaxisand
theZ-axismotion
a:
0.015/300
b:
1.10
主轴在Z轴方向之移(松)
动量
MovementofmainspindleinZaxisdirection
1.11
主轴端面之偏摆
Runoutofmainspindleoutersurface
1-4
0.01
1.12
主轴外面之偏摆
0.01mm
1.13
床台X轴方向运动之直线度
StraightnessoftablemovementintheXaxis.
1.Applyafixedindicatortothestraightedgeasthefigureshown.
2.Adjusttogetreadingatbothendsofthestraightedge.
2.Movethetable300mminX-axisdirection.
3.Recordthelargestvaluedifferenceasthemeasurementvalue.
0.01/300
1.14
床台Y轴方向运动之直线度
StraightnessoftablemovementintheYaxis
1-5
1.15
旋转台旋转偏摆
Tablerunout(XY)
0.015mm/300
1.16
Tablerunout(Z)
0.005mm
1.17
车刀角度换刀後重复定位精度
Repeatabilityoftoolangleaftertoolchange.
0.001mm
1.18
车刀角度停止後重复定位精度
Repeatabilityoftoolangleaftertoolstop.
1.20
车刀加工後定位精度
Repeatabilityoftoolangleaftermachiningpart
1.21
主轴振动检测
Spindlevibrationdetection
≦0.6mm/s
(Ref)
2.0定位精度检查Positioningaccuracyinspection单位Unit:
2.1
直线运动之定位精度
ISO230-2
循环次数:
2次
Positioningaccuracyofstraightlinemovement
By
Cycletimes
:
Twotimes
X
L≦1000
1000<L≦2000
L≧2000
0.02
Y
Z
单位Unit:
sec
2.2
回转运动之定位精度
C
15〞
1-7
3.0反复精度检查Repetitionaccuracyinspection单位Unit:
3.1
直线运动之反复定位精度ISO230-2
Positioningrepeatabilityofstraightlinemovement
0.006
3.2
回转运动之重复定位精度
8〞
1-8
3.3
Maxreversalvalue
最大反冲值
PositionaccuracyqualifiedtoISO230-2
4.0循圆精度检查Repetitionaccuracyinspection单位Unit:
4.1
循圆精度
Roundness
GeometrycontouringevaluatedbyRenishawBallbarsystem(ISO230-1)
XY
XZ
1-9