TD信令121Word文件下载.docx
《TD信令121Word文件下载.docx》由会员分享,可在线阅读,更多相关《TD信令121Word文件下载.docx(18页珍藏版)》请在冰豆网上搜索。
DirectTransfer
CN向RNC发起鉴权请求
downlinkDirectTransfer
鉴权请求,消息内容与上一条一致,只是通过RNC转发给UE
uplinkDirectTransfer
UE给RNC返回鉴权响应
鉴权响应,通过RNC转发给CN
CommonID
CN将UE的IMSI下发给RNC
完成上述过程,UE已经能够直接和CN发生信息交互
进行一些基本配置的直传消息,确认UE和CN的通信,至此信令通道已经完全建立,可以进行数据交互了
RabAssignmentRequest
CN向RNS发起RAB指派
RadioLinkReconfigurationPrepare
RNC向NODEB发起无线链路重配,重新配置CS电话速率
RadioLinkReconfigurationReady
radioBearerSetup
RNS向UE发起RB指派
RadioLinkReconfigurationCommit
radioBearerSetupComplete
RabAssignmentResponse
至此RAB指派完成,UE可以进行正常通话
DirectTransfer(振铃)
振铃及接续过程,至此UE之间已经开始正常通话。
通话结束,UE主动发起与CN断开
CN通知UE与网络释放
UE释放完成
IuReleaseCommand
CN向RNC发起IU口的释放
IuReleaseComplete
RNC释放IU口
rrcConnectionRelease
RNC向UE发起空口释放
rrcConnectionReleaseComplete
UE释放空口
RadioLinkDeletionRequest
RNC向NODEB发起无线链路删除请求
RadioLinkDeletionResponse
NODEB删除无线链路
1)、rrcConnectionRequest
establishmentCause=TRRC_originatingConversationalCall说明这是主叫业务
2)、RAB指派之前的信令和UE开关机的信令内容差不多,就不在描述。
3)、RabAssignmentRequestRAB指派是由CN下发给RNC
rAB_Parameters.trafficClass=0
说明该卡的签约类型为会话类
注意:
语句中0表示会话类业务1表示流类业务2表示交互类3表示背景类
rAB_Parameters.maxBitrate.n=1
说明目前的RAB指派中只有一种最大速率
rAB_Parameters.maxBitrate.elem[0]=12200
说明卡签约的最大速率是12.2K
Parameters.guaranteedBitRate.elem[0]=12200
卡签约的保证速率为12.2k
rAB_SetupOrModifyItemFirst.userPlaneInformation.uP_ModeVersions.data=0002说明目前CN用户面版本为2,即速率决定权在CN,即CN下发那种速率的业务RNC就用那种速率的业务。
CN的用户面版本如果是1则决定权在RNC,即速率的选择由RNC来决定
transportLayerAddress.numbits=160
transportLayerAddress.data=0101010000000000000000000000000000000000
MGW的ATM地址长度和ATM地址
4)、RadioLinkReconfigurationPrepareRNC向NODEB发起无线链路重配,重新配置CS电话速率
uL_Code_InformationModify_ModifyList_RL_ReconfPrepTDDLCR.elem[0].dPCH_ID=100
uL_TimeslotLCR_Information_RL_ReconfPrepTDD.elem[0].timeSlotLCR=3
uL_Code_InformationModify_ModifyList_RL_ReconfPrepTDDLCR.elem[0].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=7
上行的DPCHID为100,上行占用时隙3上的码道编号为7,码道编号为7的意思是在时隙3中的16个码道占用两个码道。
dL_Code_LCR_InformationModify_ModifyList_RL_ReconfPrepTDD.elem[0].dPCH_ID=139
dL_Timeslot_LCR_InformationModify_ModifyList_RL_ReconfPrepTDD.elem[0].timeSlotLCR=4
dL_Code_LCR_InformationModify_ModifyList_RL_ReconfPrepTDD.elem[0].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=15
下行的DPCHID为139,下行占用时隙4上的码道编号为15,码道编号为15的意思是在时隙4中的16个码道占用1个码道。
由于业务速率在变化,具体码道占用情况需要看多次的无线链路重配准备消息,在每一次的无线链路重配准备中都会告知这个码道是增加还是删除,才能得出确切的码道占用情况。
在radioBearerSetup/radioBearerReconfiguration中我们可以看到每次无线链路重配准备后UE占用的码道
dCH_SpecificInformationList.elem[0].dCH_ID=1
ul_TransportFormatSet.dynamicParts.elem[1].nrOfTransportBlocks=1
ul_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=148
ul_TransportFormatSet.semi_staticPart.transmissionTimeInterval=2
dl_TransportFormatSet.dynamicParts.elem[1].nrOfTransportBlocks=1
dl_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=148
dl_TransportFormatSet.semi_staticPart.transmissionTimeInterval=2
上下行的信令速率为:
1×
(148-12)/40=3.4k
因此该信令链路DCH_ID=1速率是3.4Kbps
dCH_SpecificInformationList.elem[0].dCH_ID=2
ul_TransportFormatSet.dynamicParts.elem[0].nrOfTransportBlocks=0
ul_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=39
ul_TransportFormatSet.dynamicParts.elem[2].nrOfTransportBlocks=1
ul_TransportFormatSet.dynamicParts.elem[2].transportBlockSize=81
ul_TransportFormatSet.semi_staticPart.transmissionTimeInterval=1
dl_TransportFormatSet.dynamicParts.elem[0].nrOfTransportBlocks=0
dl_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=39
dl_TransportFormatSet.dynamicParts.elem[2].nrOfTransportBlocks=1
dl_TransportFormatSet.dynamicParts.elem[2].transportBlockSize=81
dl_TransportFormatSet.semi_staticPart.transmissionTimeInterval=1
dCH_SpecificInformationList.elem[1].dCH_ID=3
ul_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=103
dl_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=103
dCH_SpecificInformationList.elem[2].dCH_ID=4
ul_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=60
dl_TransportFormatSet.dynamicParts.elem[1].transportBlockSize=60
由于是CS业务所以在传输信道里面由3个DCH。
分别是如下:
DCH=2,TTI=20,TB=0、39、81
DCH=3,TTI=20,TB=0,103
DCH=4,TTI=20TB=0,60
可以计算出上下行最大速率:
maxBitrate=(81+103+60)/20=12.2k
5)、radioBearerSetupRNC向UE发送RRC协议的RB建立消息
dl_CCTrCH_TimeslotsCodes.firstIndividualTimeslotInfo.timeslotNumber=4
dl_TS_ChannelisationCodesShort.codesRepresentation.u.bitmap.numbits=16
dl_TS_ChannelisationCodesShort.codesRepresentation.u.bitmap.data=0003
DL时隙为4,所占用的码道为16进制的0003,换算成2进制之后为0000000000000011
表示在此次呼叫过程中下行DCH占用时隙4的两个码道。
3、PS呼叫过程。
UE发起RRC连接请求,在请求消息中携带了手机能力信息
RNC给nodeb配置信令数率
NODEB上报给RNC空口已经同步
UE向CN发起attchreq
RNC向CN转发attchreq
鉴权过程
SecurityModeCommand
完整性和加密过程
securityModeCommand
securityModeComplete
SecurityModeComplete
CN下发给RNC,目前ps业务中UE使用的IMSI号
CN回复给UE,Attachaccept
UE回复CN,Attachcomplete
UE向CN发起PDP激活请求
CN下发给UTRAN,告诉UTRAN目前的配置上下业务最大的数率,业务类型等等
重配中RNC告诉NODBE应该配置的业务速率的组合是哪些,如果之前的使用的是高速信令的话,通过这条消息就将信令速率降成低速
至此RAB指派完成,UE可以进行PS业务
CN下发给UE,PDP激活成功
1)RabAssignmentRequest
rAB_SetupOrModifyItemFirst.rAB_Parameters.trafficClass=2
说明该卡的签约类型为交互类
rAB_SetupOrModifyItemFirst.rAB_Parameters.maxBitrate.n=2
说明目前的RAB指派中有两种种最大速率
rAB_SetupOrModifyItemFirst.rAB_Parameters.maxBitrate.elem[0]=384000
说明卡签约下行最大速率是384K
rAB_SetupOrModifyItemFirst.rAB_Parameters.maxBitrate.elem[1]=64000
说明卡签约上行行最大速率是64K
由于是交互类业务不存在保证速率
卡签约为会话类和流类时有最大速率和保证速率,签约为交互类和背景类是没有保证速率,只有最大速率。
rAB_SetupOrModifyItemFirst.userPlaneInformation.uP_ModeVersions.numbits=16
rAB_SetupOrModifyItemFirst.userPlaneInformation.uP_ModeVersions.data=0001
说明CN的用户面版本是1,决定权在RNC,即速率的选择由RNC来决定
transportLayerInformation.transportLayerAddress.data=8A010105
此次业务承载在SGSN用户面地址为138.1.1.5的用户面板SGUP上;
在SGSN一般是一个SGUP单板一个用户面地址。
2)RadioLinkReconfigurationPrepare
uL_Timeslot_InformationLCR.elem[0].timeSlotLCR=2
uL_Code_InformationList.elem[0].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=3上行占用的TS2时隙中的码道编号为3的相关码道
dL_Timeslot_InformationLCR.elem[0].timeSlotLCR=6
.dL_Code_LCR_Information.elem[0].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=15
.dL_Code_LCR_Information.elem[1].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=16
.dL_Code_LCR_Information.elem[2].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=17
.dL_Code_LCR_Information.elem[3].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=18
.dL_Code_LCR_Information.elem[4].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=19
.dL_Code_LCR_Information.elem[5].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=20
.dL_Code_LCR_Information.elem[6].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=21
.dL_Code_LCR_Information.elem[7].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=22
.dL_Code_LCR_Information.elem[8].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=23
.dL_Code_LCR_Information.elem[9].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=24
.dL_Code_LCR_Information.elem[10].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=25
.dL_Code_LCR_Information.elem[11].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=26
.dL_Code_LCR_Information.elem[12].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=27
.dL_Code_LCR_Information.elem[13].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=28
.dL_Code_LCR_Information.elem[14].tdd_ChannelisationCodeLCR.tDD_ChannelisationCode=29
.dL_Code_LCR_Information.elem[15].tdd_ChannelisationCodeLCR.tDD_Channe