仪表防爆及接地系统施工方案文档格式.docx
《仪表防爆及接地系统施工方案文档格式.docx》由会员分享,可在线阅读,更多相关《仪表防爆及接地系统施工方案文档格式.docx(11页珍藏版)》请在冰豆网上搜索。
正确完成仪表接地系统,对保证设备及人身安全,保证装置安全运行意义重大。
为了高速优质地完成装苣防爆及接地施工任务,特编制本方案。
2编制依据:
2」设计施工图及其它设计文件。
2.2现行《自动化仪表工程施工及验收规范》。
2.3现行的《电气装1T安装工程施工及验收规范》。
2.4现行《自动化仪表工程质量检验评泄标准》。
2.5厂商提供的产品安装使用说明书等技术文件。
2.6公司《质量保证手册》、《质量体系子程序》及英支撑性文件。
3•工程概况
工程槪况应包括:
工程名称、地点、规模、特点、范用、主要技术参数、主要实物工程量、工期要求及投资等。
4.防爆施工:
ExplosioproofConstruction:
4.1一般规左:
GeneralRegulations:
4.1.1爆炸和火灾危险区域使用的电气、仪表设备的防爆形式及配线方式必须符合设计要求,并满足使用区域的防爆等级规定。
Thestyleofexplosion-proofandwiringforelectricequipmentandinstrumentequipment,whichusedinexplosionandfiredangerousareas,mustaccordwiththedesignrequirementandcontentwithexplosionproofclassstipulation.
4.1.2安装在爆炸和火灾危险区域的仪表、电气设备和材料,必须具有符合现行国家或行业标准中规定的防爆质量技术鉴定文件和防爆产品出厂合格证书。
设备、材料的外观应无损伤和裂纹。
Concerningelectricandinstrumentalequipmentandmaterialthatisinstalledinexplosionandfiredangerousarea,theirexplosion-proofqualitytechniqueappraisaldocumentandexplosion-proofmanufacturecertificatemustbecompliancewiththenewstandardrequirementofcountiyorvocation・Tliei'
earen'
tdamageandcrackinappearanceofdeviceandmaterial.
4.1.3在爆炸和火灾危险场所使用的防爆电气、仪表设备,应有铭牌和防爆标志,并在铭牌上标明国家授权的部门所发给的防爆合格证编号。
Fortheexplosion-proofelectricandinstrumentalequipmentthatisusedinexplosionandfiredangerousarea,thenameplateandexplosion-proofmarkshouldappearontheequipment,thenumberofexplosion-proofcertificateissuedbythedepartmentofnationalaccreditationshouldbeprovidedonnameplate.
4.1.4任爆炸和火灾危险场所安装的正压通风的仪表盘(箱)、接线箱及电气、仪表设备、除本质安全型外,应有“电源未切断不得打开”的标志。
Thepluspressureventilationinstrumentpanel(box),junctionbox,electricequipmentandinstrumentequipmentinstalledinexplosiveandfiredangerousarea,excepttheintrinsicallysafetype,itshouldhas“Donotopenwhenenergized"
notice.
4.1.5仪表电气线路采用的电缆沟、汇线槽、保护管和仪表连接管路在穿越不同防爆等级的爆炸和火灾区域的分隔间壁时,在分隔间壁外,必须做充填密封。
Fortrench,cabletray,protectionpipeusedforinstrumentelectriccircuitandinstrumentconnectionpiping,iftheycrosstheseparatedroomindifferentexplosion-proofclassexplosionandfirearea,fillingandsealingshouldbedoneoutsidetheseparatedroom・4.2设备安装
ErectingEquipment:
4.2.1采用正压通风防爆的仪表盘(箱),接线箱,安装后应保证箱内压力维持在不低于设计规左的压力值,当有低压力时,苴联锁或报井装置动作应准确、可靠。
Fortheexplosion-proofinstrumentpanel(box),junctionboxwithpluspressureventilation,aftertheyareinstalled,thepressureinboxshouldbeensurednolowerthanthedesignpressure・theinterlockandalarmunitshouldactcorrectlyandreliablywhenthepressureislow.
4.2.2釆用正压通风防爆的仪表盘(箱)、接线箱,其正压力通风管路必须保持畅通,且不宜安装切断阀。
Theexplosion-proofinstrumentpanel(box),junctionboxadoptingpluspressureairiness,itspluspressureairinesspipingmustremainaccessibleandshouldnotmountshuttingoffvalue・
423在爆炸和火灾危险场所安装的仪表箱、分线箱、接线盒及防爆仪表、电气设备引入电缆时,应采用防爆密封填料进行密封:
多根电缆穿一根管时,可用密封盒并用适当填充料密封。
外壳上多余的孔应做防爆密封。
Fortheinstrumentbox,junctionbox,wiringbox,explosion-proofinstrumentandelectricequipmentwhichinstalledinexplosionandfiredangerousareas,theentranceofcableshouldbesealedwithexplosion-proofsealfilling・Whenoneconduitcontainsmultiplecable,theentrancecanmountsealingboxwithproprietyfilling・Doexplosion-proofsealingtospareholesinshell.
4.2.4防爆仪表箱、分线箱、接线箱的门(盖)应有弹性密封垫圈,或隔防密封而连接螺栓应均匀紧密,并应有弹簧垫。
Coversshouldhavespringsealingwasherforexplosion-proofinstrumentbox,junctionbox,andconnectionbox・Andconnectionboltsandnutsofseparatingandpreventingfaceshallbetightequablyandhavespringwasher.
4.2.5防爆电气、仪表设备的安装应牢固,内部接线必须正确、牢固,并有防松和防拔脱装宜。
Theexplosion-proofelectricandinstrumentdevicesshallbeinstalledfirmly.Insidewiringmustbecorrectandfirmwithlooseness-proofandshedding-proofunit・
3电气线路安装
ErectingElectricalcableline:
4.3.1穿越不同等级的爆炸和火灾危险区域分隔间壁的电缆沟的密封措施:
Sealingwayfortrenchthatcrossesseparatedwallsbelongingtodifferentclassofexplosionandfiredangerousareas:
a.电缆沟内充砂密封,可敷设一层电缆,充填一层砂,砂层厚约100mm.电缆全部敷设完后,充砂填满电缆沟。
Methodoffillingfinesandintotrench:
fillingone-layersandabout100mmdepthafterinstallonelayercable・Thetrenchshallbefullofsandafterallcablelayout.
b.在分界处两侧安装隔板,隔板之间充砂,长度不少于lm。
Theseparatedboardsshouldbefixedatbothsidesofinterface,zonebetweenboardsshallbefilledwithsand,andthelengthisnolessthanlm.
c.在分界处用阻火密封填料充填。
Sealingwithfire-resistantfillingattheinterfaces.
4.3.2汇线槽穿越不同级别的爆炸,火灾危险区域分界处时,可采取的密封播施:
Takingairproofmeasureswherecabletraypassesthroughtheinterfaceofdifferentclassexplosionandfiredangerousareas:
a.在分界处作气密砂封。
Carryoutsealwithsandattheinterface・
b.在分界处用阻火密封填料充填,形成密封阻挡层。
Sealwithfire-resistantsealfillingattheinterfaceandformsealingandresistant