IFR 266503000mAh32V 磷酸铁锂电池规格书超详细版.docx
《IFR 266503000mAh32V 磷酸铁锂电池规格书超详细版.docx》由会员分享,可在线阅读,更多相关《IFR 266503000mAh32V 磷酸铁锂电池规格书超详细版.docx(18页珍藏版)》请在冰豆网上搜索。
IFR266503000mAh32V磷酸铁锂电池规格书超详细版
深圳市银凯动力科技有限公司
SHENZHENYINKAIPOWERTECHNOLOGYCo.,Ltd
VER:
A
地址:
广东省深圳市坪山新区金荔科技园4栋
TEL:
86(0)0755-23088336FAX:
86(0)0755-23088396
DATE:
2015/10/24
CylindricalLIFEPO4Battery
Specification
圆柱型磷酸铁锂电池规格书
MODEL/型号:
IFR26650-3000mAh3.2V
PreparedBy/Date
编制/日期
CheckedBy/Date
审核/日期
ApprovedBy/Date
批准/日期
冯时春/2015.10.24
Customer
Approval客户批准
Signature确认
Date日期
CompanyName:
公司名称:
CompanyStamp:
客户印章:
---保密文件---
AmendmentRecords
(修正记录)
Edition
(版本)
Description
(记述)
Preparedby
(编制)
Approvedby
(批准)
Date
(日期)
A
FirstPublish
冯时春
2015/10/24
1Scope(适用范围)
ThisspecificationisappliedtothereferencebatteryinthisSpecificationthatmanufacturedbyYinkaiPowerTechnologyCo.,Ltd.
本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。
2ProductSpecification(产品技术规格)
Table1(表1)
No.
(序号)
Item
(项目)
GeneralParameter
(常规参数)
Remark
(备注)
1
RatedCapacity
(额定容量)
Typical
(标称容量)
3000mAh
Standarddischarge(0.2C5A)afterStandardcharge
(标准充电后0.2C5A标准放电)
Minimum
(最小容量)
2850mAh
2
NominalVoltage
(正常电压)
3.2V
MeanOperationVoltage
(即工作电压)
3
Voltageatendof
Discharge
(放电终止电压)
2.5V
DischargeCut-offVoltage
(放电截止电压)
4
ChargingVoltage
(充电电压)
3.65V
5
InternalImpedance
(内阻)
≤30mΩ
InternalresistancemeasuredatAC1KHZafter50%charge
(半电态下用交流法测量内阻)
Themeasuremustusesthenewbatteriesthatwithinoneweekaftershipmentandcycleslessthan5times
(使用出货后不到一个星期及循环次数少于5次的新电池测量)
6
Standardcharge
(标准充电)
ConstantCurrent0.2C5A
ConstantVoltage3.65V
0.01Ccut-off
(持续电流:
0.2C5A
持续电压:
3.65V
截止电流:
0.01C)
7
Standarddischarge
(标准放电)
Constantcurrent0.2C5A
endvoltage2.5V
(持续电流:
0.2C5A
截止电压:
2.5V)
Continuousthetable1(续表1)
No.
(序号)
Item
(项目)
GeneralParameter
(常规参数)
Remark
(备注)
8
Fastcharge
(快速充电)
ConstantCurrent0.5C
ConstantVoltage3.65V
0.01Ccut-off
(持续电流:
0.5C
持续电压:
3.65V
截止电流:
0.01C)
9
Fastdischarge
(快速放电)
Constantcurrent0.5C
endvoltage2.5V
(持续电流:
0.5C
截止电压:
2.5V)
10
MaximumContinuousChargeCurrent
(最大充电持续电流)
1.0C
11
MaximumContinuousDischargeCurrent
(最大放电持续电流)
1.5C
12
OperationTemperatureRange
(工作温度范围)
Charge(充电):
0~45℃
60±25%R.H.
BareCell
(电池储存湿度范围)
Discharge(放电):
-10~60℃
13
StorageTemperatureRange
(储存温度范围)
Lessthan1year:
-20~25℃
(小于一年:
-20~25℃)
60±25%R.H.
attheshipmentstate
(出货状态时的湿度范围)
lessthan3months:
-20~40℃
(小于3个月:
-20~40℃)
Lessthan7day:
-20~65℃
(小于7天:
-20~65℃)
14
CellDimension
(单体电芯尺寸)
High/高度:
66.2±0.3mm
InitialDimension
(初始尺寸)
Diameter/直径:
26.0±0.25mm
3PerformanceAndTestConditions(电池性能及测试条件)
3.1StandardTestConditions(标准测试条件)
Testshouldbeconductedwithnewbatterieswithinoneweekaftershipmentfromourfactoryandthecellsshallnotbecycledmorethanfivetimesbeforethetest.Unlessotherwisespecified,testandmeasurementshallbedoneundertemperatureof23±3℃andrelativehumidityof45~85%.Ifitisjudgedthatthetestresultsarenotaffectedbysuchconditions,thetestsmaybeconductedattemperature15~30℃andhumidity25~85%RH.
测试必须使用出厂时间不超过一个星期的新电池,且未进行过五次以上的充放电循环。
除非特别说明,否则测试会在温度23±3℃,相对湿度45~85%的条件下进行。
如果经鉴定测试结果不受上述条件影响,测试也可以在温度15~30℃,相对湿度25~85%RH的条件下进行。
3.2MeasuringInstrumentorApparatus(测量器具及设备)
3.2.1DimensionMeasuringInstrument(尺寸测量器具)
Thedimensionmeasurementshallbeimplementedbyinstrumentswithequalormore
precisionscaleof0.01mm.
尺寸测量器具的精度等级应不小于0.01mm。
3.2.2Voltmeter(伏特计)
Standardclassspecifiedinthenationalstandardormoresensitiveclasshavinginnerimpedancemorethan10kΩ/V
按照国家标准指定规格等级或采用灵敏度更高的,测量电压时内阻不应小于10kΩ/V。
3.2.3Ammeter(安培计)
Standardclassspecifiedinthenationalstandardormoresensitiveclass.Totalexternal
resistanceincludingammeterandwireislessthan0.01Ω.
按照国家标准指定规格等级或采用灵敏度更高的,包括电流表及电线在内的总外阻应小于0.01Ω。
3.2.4ImpedanceMeter(电阻计)
Impedanceshallbemeasuredbyasinusoidalalternatingcurrentmethod(1kHzLCRmeter).
内阻测试仪测量原理应为交流阻抗法(1kHzLCR)。
3.3StandardCharge\Discharge(标准充放电)
3.3.1StandardCharge:
Testprocedureanditscriteriaarereferredasfollows:
标准充电:
测试过程及标准如下:
0.2C5A=600mA
Chargingshallconsistofchargingata0.2C5Aconstantcurrentrateuntilthecellreaches3.65V.Thecellshallthenbechargedatconstantvoltageof3.65voltswhiletaperingthechargecurrent.Chargingshallbeterminatedwhenthechargingcurrenthastaperedto0.01C.Chargetime:
Approx5.5h,Thecellshalldemonstratenopermanentdegradationwhenchargedbetween0ºCand45ºC.
电池先0.2C5A恒流充至3.65V,当充电电流逐渐减小时再以3.65V恒压充至电流减小到0.01C,充电时间大约为5.5个小时。
在0℃-45℃内充电电池应没有永久损害。
3.3.2StandardDischarge(标准放电)
0.2C5A=600mA
Cellsshallbedischargedataconstantcurrentof0.2C5Ato2.5volts@23º3C
电池以0.2C5A恒流放电至2.5V@23º3C
3.3.3Ifnootherwisespecified,theresttimebetweenChareandDischargeamountto30min.
如果没有特别说明,电池充放电间隔时间为30分。
3.4Appearance(外观)
Thereshallbenosuchdefectasflaw,crack,rust,leakage,whichmayadverselyaffectcommercial
valueofbattery.
电池外观应没有划伤、破裂、污渍、生锈、漏液等影响市场价值的缺陷存在。
3.5InitialPerformanceTest(初始性能测试)
Table2(表2)
Item
(项目)
TestMethodandCondition
(测试方法及条件)
Requirements
(要求)
(1)Open-Circuit
Voltage
(开路电压)
Theopen-circuitvoltageshallbemeasuredwithin24hoursafterstandardcharge.
(标准充电后24小时内测量开路电压)
≥3.3V
(2)Internalimpedance
(初始内阻)
InternalresistancemeasuredatAC1KHzafter50%charge.
(半充电状态下,测量其AC1KHz下的交流阻抗)
≤30mΩ
(3)MinimalRated
Capacity
(最小额定容量)
Thecapacityon0.2C5Adischargetillthevoltagetaperedto2.5Vshallbemeasuredafterrestedfor30minthenfinishstandardcharge.
(标准充电后,搁置30min,测量0.2C放电至2.5V截止电压所放出的容量)
DischargeCapacity
(放电容量)
≥2850mAh
3.6TemperatureDependenceofdischargecapacity(放电温度特性)
Cellsshallbechargedper3.3.1anddischarged@0.2C5Ato2.5volts.ExcepttobedischargedattemperaturesperTable3.Cellsshallbestoredfor3hoursatthetesttemperaturepriortodischargingandthenshallbedischargedatthetesttemperature.Thecapacityofacellateachtemperatureshallbecomparedtothecapacityachievedat23ºCandthepercentageshallbecalculated.EachcellshallmeetorexceedtherequirementsofTable3.
电池按3.3.1规定充电。
按表3的温度中放电,电池必须先在该试验温度中放置3个小时。
在每一个温度中的放电容量应不小于表3的要求。
Table3(表3)
DischargeTemperature
(放电温度)
0℃
23℃
45℃
60℃
DischargeCapacity(0.2C5A)
(放电容量/0.2C5A)
60%
100%
97%
95%
3.7CycleLifeandLeakage-Proof(循环寿命及漏液试验)
Table4(表4)
No.
(序号)
Item
(项目)
Criteria
(标准)
TestConditions
(测试条件)
1
CycleLife
(循环寿命)
Higherthan80%oftheInitialCapacitiesoftheCells
(初始容量的80%)
Carryout1500cycle
Charging/Discharginginthebelowcondition.
◆Charge:
StandardCharge,per3.3.1
◆Discharge:
0.2C5Ato2.5V
◆RestTimebetweencharge/discharge:
30min.
◆Temperature:
23±3℃
循环1500次
充放电按以下条件:
◆充电:
标准充电,按3.3.1规定
◆放电:
0.2C5A放至2.5V
◆搁置:
30min.
◆温度:
23±3℃
2
Leakage-Proof
(漏液试验)
Noleakage
(visualinspection)
(没有漏液/目测)
Afterfullchargewithstandardcharge,storeat60±3℃,60±10%RHfor1month.
标准充电条件下充满电后在温度60±3℃,湿度60±10%RH下储存一个月
4.MechanicalcharacteristicsandSafetyTest(安全测试及机械特性)
Table5(表5)(Mechanicalcharacteristics)
No.
(序号)
Items
(项目)
TestMethodandCondition
(测试方法及条件)
Criteria
(标准)
1
VibrationTest
振动测试
Afterstandardcharging,fixedthecelltovibrationtableandsubjectedtovibrationcyclingthatthefrequencyistobevariedattherateof1Hzperminutebetween10Hzan55Hz,theexcursionofthevibrationis1.6mm.Thecellshallbevibratedfor30minutesperaxisofXYZaxes.
将标准充电后的电芯固定在振动台上,沿X、Y、Z三个方向各振动30分钟,振幅1.6mm,振动频率为10Hz~55Hz,每分钟变化1Hz。
Noleakage
无泄漏
Nofire
不起火
2
DropTest
跌落测试
Thecellistobedroppedfromaheightof1metertwiceontoconcreteground.
将标准充电后的电芯从1米高度跌落至混凝土地面2次
Noexplosion,
Nofire,noleakage
无爆炸、无起火、无泄漏
Table6(表6)(SafetyTest)
Item
(项目)
Battery
Condition
(电池要求)
TestMethod
(测试方法)
Requirements
(要求)
Crush
(挤压试验)
Fresh,
Fullycharged
(充满电的新电池)
Crushbetweentwoflatplates.Appliedforceisabout13kN(1.72Mpa)for30min.
(电池放置在两块平面金属板间,施加13KN(1.72Mpa)的作用力,且持续保持30分钟)
Noexplosion,
Nofire
(无起火无爆炸)
Short
Circuit
(短路试验
20℃)
Fresh,
Fullycharged
(充满电的新电池)
Eachtestsamplebattery,inturn,istobeshort-
circuitedbyconnectingthe(+)and(-)terminalsofthebatterywithaCuwirehavingamaximumresistanceloadof0.1Ω.Testsaretobeconductedatroomtemperature(20±2℃).
(在常温下约20±2℃依次把每个样品电池的正负极用铜线连接起来使电池外部短路--线路总电阻不超过0.1Ω)
Noexplosion,
NofireTheTemperatureofthesurfaceoftheCellsarelowerthan150℃
(无起火无爆炸
电池表面温度应低于150℃)
Short
Circuit
(短路试验
60℃)
Fresh,
Fullycharged
(充满电的新电池)
Eachtestsamplebattery,inturn,istobeshort-
circuitedbyconnectingthe(+)and(-)terminalsofthebatterywithaCuwirehavingamaximumresistanceloadof0.1Ω.Testsaretobeconductedattemperature(60±2℃).
(在常温下约60±2℃依次把每个样品电池的正负极用铜线连接起来使电池外部短路--线路总电阻不超过0.1Ω)
Noexplosion,
NofireTheTemperatureofthesurfaceoftheCellsarelowerthan150℃
(无起火无爆炸
电池表面温度应低于150℃)
Impact
(冲击试验)
Fresh,
Fullycharged
(充满电的新电池)
A56mmdiameterbarisinlayedintothebottomofa10kgweight.Andtheweightistobedroppedfromaheightof1montoasamplebatteryandthenthebarwillbeacrossthecenterofthesample.(用一条直径为56mm的圆棒放置在电池中央,将一10Kg的重锤从1m的高度垂直落下在电池的中心位置)
Noexplosion,
Nofire
(无起火无爆炸)
Forced
Discharge
(过放试验)
Fresh,
Fullycharged
(充满电的新电池)
Dischargeatacurrentof1C5Afor2.5h.
(以1C的电流放电2.5小时)
Noexplosion,
Nofire
(无起火无爆炸)
5.Cautionsinuse(谨慎使用)
Toensureproperuseofthebatterypleasereadthemanualcarefullybeforeusingit.
(为确保正确使用电池,使用前请仔细