船体设计常用语.docx

1、船体设计常用语船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明A1ABOUTABT大约2ABOVE BASE LINE A/B离基线的距离3ACCESS HOLE ACC. HOLE通道孔4ADDITIONAL ADD.附加的5AFTER PERPENDICULAR A.P.艉柱6AFTERWARD AFT.(A)船艉方向7AFT PEAK TANK A.P.TK艉尖舱8AIR HOLE A/H透气孔9ALIGNMENT (MOULD LINE )ALIGNMENT对齐10ANGLE A角钢11ARRANGEMENT ,ARRT布置12ASSEMBLY ASSY装配B1BAS

2、E LINE B.L基线2BEAD BEAD焊缝堆高3BEAM BEAM梁4BILGE KEEL BLG. KELL舭龙骨5BILGE WELL B/W污水井6BLOCK BLK (B)分段7BLOCK DIVISIONBLK DIV分段划分8BOTH SIDEB.S两舷9BOTTOM BTM船底10BRACKET BKT肘板11BREADTHB型宽12BREAST HOOK B.H13BULB PLATE B.PL.,B.P球扁钢14BULKHEAD BHD舱壁15BULWARKBULWARK舷墙16BUTTOCK LINE B.L.17BUTT WELDING BUTT WELD.对接焊船

3、体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明C1CAMBER CAMBER梁拱2CARGO HOLD C/H货舱3CARLING CARLG局部加强筋4CASTING CASTG铸钢件5CENTER LINE C/L中心线6CHAIN LOCKER CHAIN CHAIN LKR.止链器7CHAIN PIPE CHAIN CHAIN PIPE锚链管8CHAMFER C.倒角9CHECKED PLATE CHK. PL花钢板10COAMING COAMG舱口围11COFFERDAM C/D隔离空舱12COLLARCOLLAR补板13COLLAR PLATE C.PL.补板14

4、CONSTRUCTION CONST.结构15CORRUGATED BILKHEAD CORR.BHD槽形隔壁16CRACK ,CRACK裂缝17CUTTING CUTTG切割D1DEAD WEIGHT TONNAGE DWT载重吨2DECK DK甲板3DECK HOUSE DK HOUSE甲板室4DEPTH（MOULDED） D型深5DETAIL DET.详图6DIAMETER DIA.直径7DIAPHRAGM DIAPH.横隔板8DOUBLE BOTTOM D.BTM，D/B双层底9DOUBLE CONTINOUS FILLET WELDING D.C.F.W.双面连续角焊10DOUBLE

5、 PLATE ,D/PL垫板11DRAFT（MOULDED） D吃水12DRAIN HOLE D/H流水孔13DRAWING DWG图纸船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明E1EACH EA.个数2ELEVATION ELEV.侧视图3ENGINE ROOM E/R机舱4ENGINE ROOM BULKHEAD E/R BHD机舱舱壁5EQUAL ANGLE E.A.等边角钢6ERECTION EREC.搭载7EXPANSION ,EXPAN. EXP.展开8EXCEPTEXC.除了 外F1FACE FLAT F/F面材2FALSE BOTTOM FALSE BT

6、M.活底3FASHION PLATE FASHION PL.4FENDERFENDER护舷材5FLAT BAR F.B.扁铁6FLOORFLOOR肋板7FORE PEAK TANK F.P.TK艏尖舱8FORE PERPENDICULAR FP艏柱9FORECASTLE DECK FCLE DK首楼甲板10FOREWARD FWD (F)船艏方向11FOUNDATION FUDN基座11FRAME FR.肋骨12FRAME SPACE F.S肋骨间距13FRESH WATER TANK F.W.TK淡水舱14FULL PENETRATION WELING F.P全熔透焊接15FUNNEL FU

7、NNEL烟囱G1GALVANIZED GALV镀锌2GENERAL ARRANGEMENTGA总布置图3GIRDER GIR 主桁梁4GRINDING ,GRINDG, (G)打磨船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明5GUTTER BAR GUTTER BAR挡水扁铁6GROSS TONNAGE GT总重量H1H-BEAM H(H)H字钢2HALF ROUND BAR R.B.半圆钢3HAND GRIP H/G手柄4HATCH HATCH舱口5HATCH COVERH/C舱口盖6HAWSE PIPE HAWSE PIPE锚链管7HEIGHT H高度8HEIGHT-

8、TENSILE STEELH.T.S高强度钢9HOLDHOLD货舱10HOLE HOLE开孔11HOPPER HANK HOPP.TK底边舱12HORIZONTAL HORI.水平I1I-BEAM I(I)“I”工字钢2INSERT PLATE INSERT PL.嵌入板3INSPECTION ,INSP.检查4INVERTED ANGLE I.A.不等边、不等厚角钢K1KNUCKLE LINE K.L折角线2KNUCKLE POINT K.P折角点L1LENGTH L长度2LIFTING BEAM LIFTG BEAM吊梁3LIFTING LUG(EYE PLATE) LIFTG LUG吊环

9、4LIGHTENING HOLE L/H减轻孔5LONGITUDINAL ,LONG.纵骨6LONGITUDINAL BHD LONG. BHD纵壁7LONGITUDINAL SPACE L.S.纵向间距船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明7LOOKING LOOKG看M1MACHINERY ARRANGEMENTM/A机舱布置图2MAIN DECK MAIN DK主甲板3MAN HOLE M/H人孔4MAN HOLE COVER M/H M/H COVER人孔盖5MARKING MK标记6MAXIMUM MAX.最大7MIDSHIP MIDSHIP船舯8MINI

10、MUM MIN.最小9MOULDEDMIL模具10MOULD LINE ML.(M)理论线N1NAVIGATION BRIDGE DECKNAV. BRI. DK驾驶甲板2NUMBER NO.号码3NON TIGHTN.T非水密4NON WATER TIGHT BULKHEAD N.W.T. BHD非水密舱壁O1OFFSETOFFSET型值2OIL TIGHT BULKHEAD O.T.BHD油密舱壁3OPENING OPENG开口4ONLY ONLY单独的5OPPOSITE OPP.相反的6OUTFITTING OUTFIT.舾装P1PAD PLATE PAD PL.垫板2PARTIAL P

11、ENETRATION WELDING P.P.深熔焊3PERFORATED FLAT DECKPERF. FLAT DK开口甲板4PILLAR PILLAR,(P)支柱船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明5PIPE HOLE P/H管子开孔6PLAN PLAN平面图7PLATE PL.(P)板8PLATFORM DECK PLATM DK中间甲板9POOP DECK POOP DK艉楼甲板10PORT P,(P)左舷11PRE-ERECTION P.E.预先搭载Q 1QUALITY CONTROL Q.C.品质管理R1RADIUS R半径2RADIUS END R

12、.E.切点3REFERENCE REF参考4ROUND BAR R.B.圆钢5RUDDER TRUNK R/T挂舵臂S1SCALE S/C比例2SEA CHEST S.C海底门3SECTION SEC截面图，横剖面图4SIDE SHELL S.SHELL舷侧外板5SPEED LOG S/L测速装置6SQUARE BAR S.B方钢7STARBOARD STBD右舷8STAYSTAY栏杆撑条9STEERING GEARS/G舵机10STEP ST. (St.)踏步11STERN FRAME S/FR.艉柱12STIFFENER STI. 扶强材13STRINGER STR.水平桁14SUB-AS

13、SEMBLY SUB ASSY小组立15SWAGE BULKING SW BHD槽形舱壁船体设计常用术语PAGE NO.DWG NO.序号全称缩语中文说明T1TACK WELDING T.W.定位焊2TANK , TK（船舶）的液体舱3TANK TOP T/TOP (T/T)舱顶4TEMPORARY TEMP.临时性的5THICKNESS THK. (t)厚度6TRANSEVERSE ,TRANS.横梁7TRANSEVERSE BULKHEAD TRANS. BHD横舱壁8TRIPPING BRACKET T.B防颠肘板9TYPICAL TYP.典型的U1UNEQUAL ANGLE U.A不等

14、边角钢2UNDER （U）下面3UPPER UPP.上面4UPPER DECK UPP. .DK上甲板V1VERTICAL VERT.垂直的2VERTICAL LADDER V/L直梯3VOID SPACE V/S空舱W1WATER BALLAST TANK W.B.TK.压载水舱2WATER TIGHT BULKHEAD W.T. BHD.水密舱壁3WEATHER DECK WEATHER DK露天甲板4WEIGHT ,W/T重量5WELDING WELDG焊接6WHEEL HOUSE TOP W/H TOP驾驶室船体设计常用术语PAGE NO.DWG NO.船体设计常用术语PAGE NO.DWG NO.