巴可DP2K系列故障代码.docx

1、巴可DP2K系列故障代码BARCO DP2K 系列故障代码译表本文将列举绝大部分会显示在巴可 DP2K系列放映机触摸屏与日志中的故障错误代码并译文备查，同时将针对部分常见的对我放映工作有价值的故障提供 解决方法。需要注意的是，某些代码会同时表示错误和警告，某些表示错误（error），某些是警告（waring ）。在“警告”状态下，放映机虽将继续维持运 转，但仍建议尽快解决导致“警报”的故障，否则， “警报”状态将有可能引发“错误”的产生，而最终导致停机事故的发生。故障代码列表如下，可用ctrl+f快捷键进行搜索：1.Code 5003: “ light sen sor - no com mun

2、i cati on ” （Error）“灯传感器-无通讯”2.Code 5004: “ lamp - no com muni cati on ” （Error）“灯-无通讯”状态解决方法灯箱没有被正确安装检查灯箱安装，并重置灯箱使用了与本机型号不匹配的灯箱选择匹配灯箱同时显示代码 5180 ( lamp house - not conn ected )见 5180与灯箱无通讯检查灯箱前端蓝色插头是否损坏3.Code 5005: “ lamp power supplies - com muni cati on failed ” (Error)“灯电源-通讯失败”状态解决方法CTRL in, CT

3、RL out线没有插紧重新连接电源模块上的CTRL接口与接 线Address线没有插紧重新连接address线主电源输入线没有插紧重新连接两组 MAIN INPUT接口与接 线其中一组电源红灯快速闪亮更换整组电源模块” (Warni ng)4.Code 5010: “ pump - refill mode is on15.Code 5102:“smps fan 1 - speed too low(Error)状态解决方法放映机切换至“补充模式”，只有冷却 泵开启等冷却液补充完毕，点击“退出补充模 式”5.Code 5042:“cold mirror fan - speed too low“冷却

4、泵-补充模式已开启” (Error)“开关电源风扇1-转速过低”16.Code 5103:“ smps fan 1 - speed low ” (Warning)“开关电源风扇1 -转速低”17.Code 5112:“ smps fan 2 - speed too low ” (Error)“开关电源风扇2 -转速过低”18.Code 5113:“ smps fan 2 - speed low ” (Warning)“开关电源风扇2 -转速低”19.Code 5122:“lamp rear fan - speed too low ” (Error)“灯后部风扇-转速过低”20.Code 512

5、3:“lamp rear fan - speed low ” (Warning)“灯后部风扇-转速低”21.Code 5132:“ elcabox fan - speed too low ” (Error)“电控盒风扇-转速过低”22.Code 5133:“ elcabox fan - speed low ” (Error)“电控盒风扇-转速低”23.Code 5160:“ engine switch - not ok ” (Error)引擎开关-不正常”24.Code 5170:“ fib - not conn ected ” (Error)“解码板-未连接”25.Code 5180: “l

6、amp house - not conn ected ” (Error)“灯箱-未连接”状态解决方法灯箱未正确安装检查灯箱是否已正确牢固安装，确认三 颗锁定螺丝已锁紧开关损坏或未接触检查灯箱右下角固定螺丝对应的放映 机内侧微动开关是否损坏或未接触风扇控制板失灵更换26.Code 5191: “ prism switch -prism) ” (Warning)-warning (lens probably touches“棱镜开关-警告（镜头可能已触动棱镜）状态解决方法镜头转动至极限，已触动到棱镜传感器重新调整镜头位置棱镜传感器失效拆除镜头并重启放映机，若仍有警告则 为棱镜传感器失效27.Cod

7、e 5212: “ pump - speed too low ” (Error)“冷却泵-转速过低”28.Code 5213: “pump - speed low“冷却泵-转速低” (Warning)29.Code 5230: “ le ns zoom positi on -(Warning)-requested target not reached ”“镜头变焦位置-没有达到预定位置”状态解决方法所使用的为手动镜头更换电动镜头并设置镜头参数已激活镜头文件无法驱动已安装镜头检查镜头型号设置是否正确镜头文件损坏删除并重建所有现有镜头文件镜头预定位置已非常接近电动镜头机 械极限手动重置镜头，或重置

8、放映机位置镜头马达失灵使用小面板上的镜头位置控制按钮，若 无反应，则为镜头马达失灵30.Code 5232: “ le ns horiz on tal shift positi on - requested target notreached ” (Warning)“镜头水平移动位置-没有达到预定位置”状态解决方法镜头文件损坏参见5230镜头预定位置已非常接近电动镜头机 械极限手动重置镜头，或重置放映机位置镜头马达失灵使用小面板上的镜头位置控制按钮，若 无反应，则为镜头马达失灵31.Code 5233: “ lens vertical shift position - requested ta

9、rget notreached ” (Warning)“镜头垂直移动位置-没有达到预定位置”参见523232.Code 5237: “ lens positi on - clear requested target time out failed(Warning)“镜头位置-接受明确指令超时”33.Code 5280: “ ambie nt - temperature too high ” (Error)“环境-环境温度过高”状态解决方法前滤网堵塞清洗或更换环境温度过高降低环境温度抽风设备失灵修复抽风设备34.Code 5281: “ ambie nt - temperature high ”

10、 (Warni ng)“环境-环境温度高”参见528035.Code 5283: “ ambie nt - temperature low ” (Warning)“环境-温度低”36.Code 5284: “ ambie nt - temperature sen sor ope n ” (Error)“环境-环境温感器断路”37.Code 5285: “ ambie nt - temperature sen sor short ” (Error)“环境-环境温感器短路”38.Code 5290: “ dmd blue - temperature too high ” (Error)“蓝DMD

11、-温度过高”39.Code 5291: “ dmd blue - temperature high ” (Warni ng)“蓝DMD -温度高”40.Code 5293: “ dmd blue - temperature low ” (Warni ng)“蓝DMD -温度低”41.Code 5294: “ dmd blue - temperature sen sor ope n ” (Error)“蓝DMD -温感器断路”42.Code 5295: “ dmd blue - temperature sen sor short ” (Error)“蓝DMD -温感器短路”43.Code 530

12、0: “ dmd gree n - temperature too high ” (Error)“绿DMD -温度过高”44.Code 5301: “ dmd gree n - temperature high ” (Warning)“绿DMD -温度高”45.Code 5303: “ dmd gree n - temperature low ” (Warning)“绿DMD -温度低”46.Code 5304: “ dmd gree n - temperature sen sor ope n ” (Error)“绿DMD -温感器断路”47.Code 5305: “ dmd gree n -

13、 temperature sen sor short ” (Error)“绿DMD -温感器短路”48.Code 5310: “lamp - temperature too high ” (Error)“灯-温度过高”状态解决方法滤网堵塞清洗或更换滤网环境温度过高降低环境温度抽风设备失灵修复抽风设备氙灯阴/阳极风扇失灵检查阴/阳极风扇转速及电压49.Code 5311: “lamp - temperature high ” (Warni ng)“灯-温度高”参见531050.Code 5314: “ lamp - temperature sensor open ” (Error)“灯 - 温感

14、器断路”51.Code 5315: “ lamp - temperature sensor short ” (Error)“灯 - 温感器短路”52.Code 5320: “ fcb - force lps off ” (Error) “风扇控制板 - 灯电源强制关闭”53.Code 5330: “ pfc heatsink - temperature too high ” (Error)“散热器 - 温度过高”54.Code 5331: “ pfc heatsink - temperature high ” (Warning)“散热器 - 温度高”55.Code 5340: “ dmd re

15、d - temperature too high ” (Error)“红 DMD - 温度过高”56.Code 5341: “ dmd red - temperature high ” (Warning) “红 DMD - 温度高”57.Code 5343: “ dmd red - temperature low ” (Warning) “红 DMD - 温度低”58.Code 5344: “ dmd red - temperature sensor open ” (Error) “红 DMD - 温感器断路”59.Code 5345: “ dmd red - temperature sens

16、or short ” (Error) “红 DMD - 温感器短路”60.Code 5350: “smps primary heatsink - temperature too high (Error)“开关电源主散热器 - 温度过高”61.Code 5351: “ smps primary heatsink - temperature high (Warning)“开关电源主散热器 - 温度高”62.Code 5360: “smps secundary heatsink - temperature too high (Error)开关电源副散热器 - 温度过高”66.Code 5401: “

17、 +30v - voltage high ” (Warning)“ +30v - 电压高”67.Code 5403: “ +30v - voltage low ” (Warning)“+30v - 电压低”68.Code 5411: “ +5v - voltage high ” (Warning)“ +5v - 电压高”69.Code 5413: “ +5v - voltage low ” (Warning)“ +5v - 电压低”70.Code 5431:“ cold mirror fan - voltage high” (Warning)“反射镜风扇 -电压高”71.Code 5432:“

18、 cold mirror fan - voltage too low” (Error)“反射镜风扇 -电压过低”72.Code 5433:“ cold mirror fan - voltage low” (Warning)“反射镜风扇 -电压低”73.Code 5441:“ engine fan - voltage high ”(Warning)“引擎风扇 - 电压高”(Error)74.Code 5442: “ engine fan - voltage too low“引擎风扇 - 电压过低”75.Code 5443: “ engine fan - voltage low ” (Warnin

19、g)引擎风扇 - 电压低”76.Code 5451:“ heat exchanger fan - voltage high” (Warning)“换热器风扇 -电压高”77.Code 5452:“ heat exchanger fan - voltage too low ” (Error)“换热器风扇 -电压过低”78.Code 5453:“ heat exchanger fan - voltage low” (Warning)“换热器风扇 -电压低”79.Code 5461:“ lamp anode fan - voltage high” (Warning)“灯阳极风扇 -电压高”80.Co

20、de 5462:“ lamp anode fan - voltage too low” (Error)“灯阳极风扇 -电压过低”81.Code 5463:“ lamp anode fan - voltage low” (Warning)“灯阳极风扇 -电压低”82.Code 5471:“ lamp cathode fan - voltage high” (Warning)“灯阴极风扇 -电压高”83.Code 5472:“ lamp cathode fan - voltage too low” (Error)“灯阴极风扇 -电压过低”84.Code 5473:“ lamp cathode fa

21、n - voltage low” (Warning)“灯阴极风扇 -电压低”85.Code 5492:“ smps fan - voltage too low ”(Error)风扇控制板风扇 - 电压过低”86.Code 5493: “ smps fan - voltage low ” (Warning)“风扇控制板风扇- 电压低”87.Code 5501:“ fib +12v - voltage high ” (Warning)“解码板 +12v -电压过高”88.Code 5503:“ fib +12v - voltage low ” (Warning)“解码板 + 12v -电压低”89

22、.Code 5521: “ motor (lens, dowser) - voltage high ” (Warning)“马达(镜头、光闸) - 电压高”90.Code 5523: “ motor (lens, dowser) - voltage low ” (Warning)“马达(镜头、光闸) - 电压低”91.Code 5531: “ pump - voltage high ” (Warning)“冷却泵 - 电压高”92.Code 5532: “ pump - voltage too low ” (Error)“冷却泵 - 电压过低”93.Code 5533: “ pump - vo

23、ltage low ” (Warning)“冷却泵 - 电压低”94.Code 5551: “ tec - voltage high ” (Warning)“珀耳贴致冷器- 电压高”95.Code 5553:“ tec - voltage low ” (Warning)“珀耳贴致冷器- 电压低”96.Code 5561:“ elcabox fan - voltage high ”(Warning)“电控盒风扇 -电压高”97.Code 5562:“ elcabox fan - voltage too low” (Error)“电控盒风扇 -电压过低”98.Code 5563:“ elcabox

24、 fan - voltage low ”(Warning)“电控盒风扇 -电压低”99.Code 5571:“ lamp rear fan - voltage high” (Warning)“灯后部风扇-电压高”(Error)lOO.Code 5572: “ lamp rear fan - voltage too low “灯后部风扇-电压过低”102.Code 5583:“+12v - voltage low(Warni ng)“+12v -电压高”“ +12v -电压低”-zero lamp power supplies103.Code 5640: “ lamp power supplie

25、sdetected ” (Error)“灯电源-没有探测到灯电源”状态解决方法两电源模块其中之一主供电电缆断开检杳电源模块上 MAINS INPUT插槽 及插线电源模块中“CTRL IN ”与“CTRL OUT” 插线断开检杳电源模块中“ CTRL IN ”与“CTRLOUT ”插槽及插线电源模块未安装到位重新安装灯电源控制板失灵更换灯电源模块闪红灯更换电源模块104.Code 5641: “ lamp power supplies - lamp is on, but smps is off(Error)状态解决方法开关电源板失灵更换灯电源模块失灵更换电源背板失灵更换105.Code 5642

26、: “ lamp power supplies - at least one lamp powersupply could not be detected ” (Error)参见5640106.Code 5643: “ lamp power supplies - com muni cati on failed with atleast one lamp power supply ” (Error)参见5640107.Code 5644: “ lamp power supplies - lamp is on, but at least onelamp power supply is off ”

27、(Error)参见5640108.Code 5646: “ lamp - set lamp on failed ” (Error)“灯-点灯失败”状态解决方法氙灯有触发，无法持续点燃1，氙灯寿命将尽，更换新灯2，触发器损坏109.Code 5647: “ lamp - lamp is off due to an error ” (Error)“灯-由于一个错误氙灯已熄灭”状态解决方法由于某些错误，灯电源被指令熄灭氙灯查看放映机日志寻找其他错误信息，首 先解决此类错误问题灯电源故障查看灯电源指示灯，若红灯闪烁则更需 换灯电源氙灯缺陷更换新灯110.Code 5654: “lamp run tim

28、e - read failed ” (Error)“灯运行时间-读取失败”111.Code 5657: “lamp run time - exceeds maximum ” (Error)“灯运行时间-已到最大寿命”状态解决方法灯箱内氙灯已达到最大使用寿命更换新灯，或重置灯信息112.Code 5658: “ lamp run time - read limits failed ” (Error)“灯运行时间-限制读取失败”113.Code 5659: “lamp run time - warni ng ” (Warni ng)状态解决方法灯箱内氙灯接近到最大使用寿命尽快更换新灯，或重置灯信息

29、114.Code 5800: “ ti-boards - system status = fail ” (Error)“ TI板-系统状态=失败”这是一个通用TI错误代码，需要进入触摸屏的“诊断-测试-自检”中勾选所 有选项并进行检测，并将检测结果提供给服务商用以查找具体故障所在。115.Code 5801: “ ti-boards - security error, please authorize ” (Error)TI板-安全错误，请授权”状态解决方法放映机的输入或通讯组件被物理重置使用授权钥匙进行重新授权，步骤如下1，确保重置部件正确安装2，开启放映机3，将授权钥匙嵌入授权插槽4，在5秒内输入口令放映机内盖被拆开(光处理器部分)方法同上安全开关失灵如果执行以上方法仍无效，更换 DCI安全开关电源背板失灵如果更换安全开关无效则更换电源背 板116.Code 5802: “ ti-boards - power up self test = fail ” (Error)“TI板-开机自检-失败”117.Code 5803: “ ti-boards - in terface board arm