模具专业词汇收集.docx

1、模具专业词汇收集模具专业词汇收集一、 入水：gate进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysi

2、s 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line喉塞：line plug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold 边钉/导边：lea

3、der pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainer plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core, return core core

4、 puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun

5、 活动臂：lever arm 分流锥：spruespreader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return b

6、ar气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting su*ce support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut height 顶针碰运水：water line interferes with ejector pin 料位出上/下模：part from cavity (core) side 模胚原身出料位：cavity direct cut on A-plate, core direc

7、t cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliminary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability, stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thermo expansion 公差：toleranc

8、e 铜公(电极）：copper electrode其他术语单词Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse m

9、achine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet

10、metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备

11、 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |plein|刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长

12、 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final in

13、spection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |skrpid|报废 scrape .v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation | ksi

14、dein|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker

15、锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板

16、hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage

17、can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺

18、陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污

19、 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/su*ce processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质

20、delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-gr

21、ade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱

22、 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation

23、评估 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch-t

24、o throw-over switching over切换 engineering, project difficulty 工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, die

25、ing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent

26、压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to c

27、ontrol管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡

28、 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑extrusion die 挤出模 extrusion molding 挤出成形eye bolt 环首螺栓 eyelet 眼孔ffacing 面车削 fading 退色 falling bal

29、l impact test 落球冲击试验family mold 成套制品模具 fantail die 扇尾形模具fatigue test 疲劳试验 favourable price 合宜价格feed 供料 feed length 送料长度feed level 送料高度 feed ring 补给环feeler gauge 测隙规 ferrite 肥粒铁ferrostatic pressure 钢铁水静压力 fettling 铸件清理fiber reinforcement 纤维强化热固性 fiber reinforcement 纤维强化复合材料file 锉刀 filing 锉刀修润filing 锉

30、削加工 filler rod 充填剂filler speck 填充料斑 fillet weld 填角焊接filling core 埋入砂心 filling-in 填砂film gate 薄膜形浇口 film play 液面花纹fine blanking 精密下料加工 fine blanking press 精密下料冲床finger pin 指形梢 finish blanking 光制下料加工finish machined plate 角形模板 finish machined round plate 圆形模板finishing 精整加工 finishing allowance 加工余量finishing slag 炼后熔渣 first