1、0368340150PCM 深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 1 of 11 Specification Approval Sheet(Polymer Cell)产品规格确认书(聚合物电池)Model/型号:BJ402025-PCMCapacity/容量:150mAhVoltage/电压:3.7V样品单号(sample number): YP-1738-03683 制定审核批准 客户确认许娟 深 圳 宝 嘉 能 源 有 限 公 司SHEN
2、ZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 2 of 11 Content目录1.Scope 3适用范围2.Model 3 型号3. .Dimensions of battery pack 3电池尺寸4. Specifications of battery pack 4电池基本特性5. Specification of cell 5电池性能6.Required Protection Functions 9保护功能7. Warranty period & Product Liability 10
3、保质期及产品责任8.Storage and Others 11贮存及其它事项 深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 3 of 11 1.Scope 适用范围This document describes the Product Specification of the Lithium-Polymer (LIP) rechargeable battery cell supplied by Baojia Battery Corporation L
4、imited). 本规格说明书描述了深圳宝嘉能源有限公司(以下简称宝嘉能源)生产的可充电聚合物锂离子电池的产品性能指标。2.Model:BJ402025-PCM 型号:BJ402025-PCM 3.Dimensions of battery 产品尺寸 Connecting Wires (1571-30#) 接线方式 Red: connect to “+” 红色接正极 Black : connect to ground “-” 黑色接负极深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A
5、 REV. : A PAGE: 4 of 11 4. Specifications of battery 电池基本特性 NO.ItemsSpecifications1Charge voltage充电电压4.2V2Nominal voltage额定电压3.7V3Nominal capacity额定容量150mAh 0.2C Discharge(0.2C放电)5Standard Charging method标准充电方法0.2C CC(constant current)charge to 4.2V,then CV(constant voltage 4.2V)charge till charge c
6、urrent decline to 0.01C0.2C CC(恒流)充电至4.2V,再CV(恒压4.2V)充电直至充电电流0.01C6Charging time充电时间Standard Charging:0.2C5A7.5hrs 标准充电: 0.2C5A7.5hrsRapid charge: 1 C5A2.5hrs快速充电: 1 C5A2.5hrs7Max.charge current最大充电电流1.0C8Max.discharge current最大放电电流1.5C9Discharge cut-off voltage放电截止电压2.80V10Operating temperature工作温度
7、Charging: 045充电: 045Discharging:045放电: 04511Storage temperature储存温度-20 +4512Cell Weight电池重量Approx:3.05g 约:3.05g 深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 5 of 11 5.Battery Cell Performance Criteria 电池性能 5.1 Electrical Characteristic 电化学性能序号NO.项目I
8、tem标准Standard测试方法Test Method1常温放电性能DischargeCharacteristics0.2C5A 5h在1标准大气压,环境温度205,相对湿度为4575的条件下,电池标准充电后(以下若没有特别说明,均在此条件下放置,皆按此充电方式),搁置30min,分别以0.2C5A进行放电至终止电压,循环三次,当有一次达到标准,即达到标准要求(下同)。Standard charged under the condition of normal atmospheric pressure and the environmental temperature of 255 and
9、4575RH, then rest for 30min and discharge at0.2C5A to the discharge cut-off voltage respectively. Charge/discharge cycle can be conducted for 3 times before meeting the Standards(the same below)2常温荷电保持能力Normal Storage放电时间4.25hDischarge Time4.25h电池标准充电后,开路放置28天,再以0.2C5A放电至终止电压。Store for 28 days after
10、 standard charged, then discharge at 0.2C5A to the discharge cut-off voltage.3循环寿命Cycle Life循环300次后放电时间42minDischarge Time42min0.2C5A放电至终止电压,搁置30min,以此模式循环300次Conduct 0.2C5A cycle for 300 times and measure final capacity.4贮存性能Long Time Storage电池贮存12个月,放电时间4h。stored for 12 months,Discharge Time4h以0.2
11、 C5A对电池充电,充入50的容量后贮存,期满后对电池进行0.2 C5A/0.2 C5A充放电。Standard charged, Discharge to the state of 50% capacity. Store for 12 months at room temperature. Conduct 0.2 C5A /0.2 C5A cycle before meeting the standard.45.2 Safety Characteristic安全性能深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-
12、WI-733-003-002/A REV. : A PAGE: 6 of 11序号NO.项目Item标准Standard测试方法Test Method1过充性能Overcharge不爆炸、不起火No fire、No explosion电池标准充电后,以3C5A电流充电至4.6V,然后转恒压充电至截至电流0.01C5A时终止。Standard charge. Charge at 3 C5A to 4.6V, then change to charge with constant voltage till the current less than or equal to 0.01 C5A. Ob
13、serve the variation of the batterys appearance2过放性能Over Discharge不起火、不爆炸No fire、No explosion电池标准充电后,以1C5A进行放电至终止电压,然后用10的电阻将电池正负极相连,搁置14天。Standard charged. Discharge at 1C5A to discharge cut-off voltage and then connect the positive and negative terminals with a resistor of 10 for 14 days.3常温短路性能Sho
14、rt Circuit at Room Temperature不爆炸、不起火最高温度150No fireNo explosionMax.temperature150电池标准充电后,置于防爆玻璃罩中直接短路其正负极(线路总电阻不大于50m),当电池温度下降到比峰值约低10 时试验结束。观察电池的温度及外观变化。Standard charged. Keep the battery into a ventilation cabinet and short-circuit the positive and negative terminals directly (general resistance s
15、hall be less than or equal to 50m). Stop the test when the temperature falls to value 10 lower than the peak value. Observe the variation of the batterys appearance and temperature.4高温短路性能Short Circuit at High Temperature不冒烟、不爆炸不起火最高温度150No fire、No explosionMax.temperature150电池标准充电后,置于552防爆箱中,放置3h后直
16、接短路其正负极(线路总电阻不大于50m),试验过程监视电池温度变化,当电池温度下降到比峰值约低10 时,结束试验。观察电池的温度及外观变化。Standard charged, Keep the battery into a ventilation cabinet of 552 and store for 3h. Short-circuit the positive and negative terminals directly (general resistance shall be less than or equal to 50m) at this temperature. Supervi
17、se the variation of the batterys temperature in the process of the test, stop the test when the temperature falls to value 10 lower than the peak value. Observe the variation of the batterys appearance and temperature.深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A R
18、EV. : A PAGE: 7 of 11 5重物冲击性能Impact不爆炸、不起火No fireNo explosion5电池标准充电后,放在平面上,并与热电偶相连,将一直径为15.8mm的棒放在电池高度方向中间位置,让重量9.1kg的重物从610mm高度自由垂落至冲击台面。Standard charge. Keep the battery connected with a thermocouple and put it on a impaction platform, place a 15.8mm diameter bar across the center of the biggest
19、surface, then let a 9.1kg heavy hammer self fall off to the platform from a height of 610mm. Observe the variation of the batterys appearance.6热冲击安全性能Hot Oven不起火、不爆炸No fire、No explosion电池标准充电后,放置于热箱中,并与热电偶相连,温度以(5 2 )/min的速率升至130 2 并保温30Min。Standard charge. Keep the battery connected with a thermoco
20、uple and put it into a circulating air oven. Temperature is raised at a rate of 5 2 per minute to a temperature of 1502 and remained for 30min at this temperature. Observe the variation of the batterys appearance.5.3 Environment Adaptation Performance环境适应性能序号NO.项目Item标准Standard测试方法Test Method1热循环性能T
21、hermal Cycle电池不漏液、不冒烟、不起火、不爆炸No smoking 、No fire、No explosion电池标准充电后,在环境温度为752的条件下开路放置48h,在-20 条件下开路放置6h,然后在室温条件下开路放置24h, 1C5A进行放电至终止电压。Standard charge the battery, then store it at 752for 48h, then -20 for 6h and room temperature for 24h.Then discharge at0.2C5A to discharge cut-off voltage.2恒定湿热性能S
22、tatic Humidity电池不起火、不爆炸放电时间3hDischarge Time 3h No remarkable deformationNo smoking explosion电池标准充电后,置于温度为402,相对湿度为90的恒温恒湿箱中,搁置48h后,取出电池205环境下搁置2h。观察电池外观变化。然后以0.2C5A放电至终止电压。Standard charge. Put the battery into a 402 and 90 RH chamber for 48h, then get it out and store it for 2h at room temperature.
23、Observe the variation of the batterys appearance and then discharge at 0.2C5A to discharge cut-off voltage, measuring final capacity.深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 8 of 11 3跌落性能Drop不起火、不爆炸放电时间255minNo smoking 、No fire、No explosionDisch
24、arge time255min6标准充电后,将电池样品由高度(最低点高度)为1m的位置自由跌落到1820mm的硬木板上,要求各面各跌落一次。然后将电池以0.2C5A放电至终止电压,做0.2C5/0.2C5循环达到要求停止,充放电循环次数不高于3次Standard charge. Then let it self fall off from a height of 1.0m (the lowest height) to a smooth wooden surface. The self fall off should be conducted from every positive and ne
25、gative direction. Then discharge at0.2C5A to discharge cut-off voltage. Conduct 0.2C5A /0.2C5A cycle for 3 times.4不同温度下的放电性能High-low Temperature DischargeA)60 时285min B)0 时240min;C)-20 时150min电池不爆炸、不起火。A)60 时285min B)0 时240min;C)-20 时150minNo fireexplosion电池标准充电后,在602条件下恒温搁置3h、以0.2C5A放电至终止电压,然后在室温条件
26、下标准充电, 依次按照02/-202的顺序在相应的恒温条件下搁置20h,以0.2C5A放电至终止电压。Standard charge. Then store for 3h at 602 and discharge at 0.2C5A to discharge cut-off voltage. then standard charge at room temperature and store for 20h according to the order of 02 /-202 and discharge at 0.2C5A measuring corresponding discharge c
27、apacity. 5振动环境适应性能Vibration电池外观无明显损伤、不漏液、不冒烟、不爆炸No remarkable damage、No smoking 、No explosion电池标准充电后,安装在振动台面上,按下面的振动频率和对应的振幅调整好试验设备,X、Y、Z三个方向每个方向上从10Hz55Hz循环扫频振动30min,扫频速率为1oct/min:A)振动频率:10Hz30Hz ;位移幅值(单振幅):0.38mm ;B)振动频率:30Hz55Hz ;位移幅值(单振幅):0.19mm。 Standard charge. Measure initial status. Equip it
28、 to the vibration platform, adjust and prepare the test equipment according to following vibration frequency and relevant swing, doing frequency sweeping from X, Y, Z three directions, each from 10Hz to 55Hz for 30 minutes of recycling, rating of which is 1oct/min:A)vibration frequency:10Hz30Hz ;Dis
29、placement breadth (single swing): 0.38mm ;B) vibration frequency: 30Hz55Hz Displacement breadth(single swing): 0.19mm。Measure final status after sweeping and Observe the variation of the batterys appearance. 深 圳 宝 嘉 能 源 有 限 公 司SHENZHEN BAOJIA BATTERY CO., LTD.DOC NO.: QR-WI-733-003-002/A REV. : A PAGE: 9 of 11 5.4 Visual inspection 外观检查 There shall be no such defect as scratch, flaw, crack, and leakage, which may adversely affect commercial value of the cell. 不允许有任何影响电池性能的外观缺陷,诸如裂纹、裂缝、泄漏等。5.5 Standard environmental test condition 标准测试环境 Unless otherwise specified, all tests stated in
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1