标准件最新国标号.docx

1、标准件最新国标号平键1 GB/T 1095-2003 平键 键槽的剖面尺寸 Square and Rectangular keyways 2 GB/T 1096-2003 普通型 平键 Square and rectangular keys 3 GB/T 1097-2003 导向型 平键 Square and rectangular keys 4 GB/T 1566-2003 薄型平键 键槽的剖面尺寸 Square and Rectangular thin keyways 5 GB/T 1567-2003 薄型 平键Square and rectangular thin keys 螺栓1 GB

2、/T 10-1988 沉头方颈螺栓Flat countersunk square neck bolts 2 GB/T 11-1988 沉头带榫螺栓Flat countersunk nib bolts 3 GB/T 12-1988 半圆头方颈螺栓Cup head square neck bolts 4 GB/T 1228-1991 钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structures 5 GB/T 1231-1991 钢结构用高强度大六角头螺栓、大六角螺母、垫圈技术条件Specification

3、s of high strength bolts with large hexagon head, large hexagon nuts,plain washers for steel structures 6 GB/T 12869-1991 机床夹具零件及部件 双头螺栓The parts and units of jigs and fixtures-Double end stud 7 GB/T 12870-1991 机床夹具零件及部件 槽用螺栓The parts and units of jigs and fixtures-Slot bolt 8 GB/T 13-1988 半圆头带榫螺栓Cu

4、p head nib bolts 9 GB/T 14-1998 大半圆头方颈螺栓 C级Cup head square neck bolts with large head-Product grade C 10 GB/T 15049.6-1996 CAD 标准件图形文件 几何图形和特性规范 螺栓CAD standard parts file-Specification of geometry and parameters-Bolts 11 GB/T 15-1988 大半圆头带榫螺栓Cup head nib bolts with large head 12 GB/T 152.4-1988 紧固件

5、六角头螺栓和六角螺母用沉孔Fasteners-Counterbores for hexagon bolts and nuts 13 GB/T 15389-1994 螺杆Threaded rods 14 GB/T 158-1996 机床工作台 T形槽和相应螺栓Machine tool tables-T-slots and corresponding bolts 15 GB/T 16674.1-2004 六角法兰面螺栓 小系列Hexagon bolts with flange-Small series 16 GB/T 16674.2-2004 六角法兰面螺栓 细牙 小系列Hexagon bolts

6、 with flange with metric fine pitch thread-Small series 17 GB/T 16938-1997 紧固件 螺栓、螺钉、螺柱和螺母通用技术条件Fasteners-General requirements for blots,screws,studs and nuts 18 GB/T 16939-1997 钢网架螺栓球节点用高强度螺栓High strength bolts for joints of space grid structures 19 GB/T 18230.1-2000 栓接结构用大六角头螺栓 螺纹长度按GB/T 3106 C级 8

7、.8和10.9级Hexagon bolts for high-strength structural bolting with large width across flats(thread lengths according to GB/T 3106)-Product grade C-Property classes 8.8 and 10.9 20 GB/T 18230.2-2000 栓接结构用大六角头螺栓 短螺纹长度 C级 8.8 和 10.9级Hexagon bolts for high-strength structural bolting with large width acros

8、s flats(short thread length)-Product grade C-Property classes 8.8 and 10.9 21 GB/T 27-1988 六角头铰制孔用螺栓 A和B级Hexagon fit bolts-Product grade A and B 22 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A和B级Hexagon fit bolts with Split pin hole on shank-Product grade A and B 23 GB/T 29.1-1988 六角头头部带槽螺栓 A和B级Hexagon bolts with s

9、lot on head-Product grade A and B 24 GB/T 29.2-1988 十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation 25 GB/T 3098.10-1993 紧固件机械性能有色金属制造的螺栓、螺钉、螺柱和螺母Mechanical properties of fasteners Bolts, scrows, studs and nuts made of non-ferrous metals 26 GB/T 3098.1-2000 紧固件机械性能 螺栓、螺钉和螺柱Mechanical propert

10、ies of fasteners made of carbon steel and alloy steel-Part 1:Bolts,screws and studs 27 GB/T 3098.13-1996 紧固件机械性能 螺栓与螺钉的扭矩试验和破坏扭矩公称直径110mm Mechanical properties of fasteners-Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm 28 GB/T 3098.6-2000 紧固件机械性能 不锈钢螺栓、螺钉

11、和螺柱Mechanical properties of fasteners-Bolts,screws and studs made of stainless-steel 29 GB/T 3099-1982 螺栓、螺钉、螺母及附件名词术语Bolts,screws,nuts and accessories-Terminology and nomenclature 30 GB/T 31.1-1988 六角头螺杆带孔螺栓 A和B级Hexagon bolts with split pin hole on shank-Product grade A and B 31 GB/T 31.2-1988 六角头螺

12、杆带孔螺栓 细杆 B级Hexagon bolts with split pin hole on shank-Reduced shank-Product grade B 32 GB/T 31.3-1988 六角头螺杆带孔螺栓 细牙 A和B级Hexagon bolts with split pin hole on shank-Fine pitch thread-Product grade A and B 33 GB/T 3103.1-2002 紧固件公差 螺栓、螺钉、螺柱和螺母Tolerances for fasteners- Bolts,screws, studs and nuts 34 GB/

13、T 3103.2-1982 紧固件公差 用于精密机械的螺栓,螺钉和螺母Tolerances for fasteners-Bolts,screws and nuts for fine mechanics 35 GB/T 3105-2002 普通螺栓和螺钉 头下圆角半径General purpose bolts and screws-Radii under the head 36 GB/T 3106-1982 螺栓,螺钉和螺柱的公称长度和普通螺栓的螺纹长度Bolts,screws and studs-Nominal lengths and thread lengths for general pu

14、rpose bolts 37 GB/T 32.1-1988 六角头头部带孔螺栓 A和B级Hexagon bolts with wire holes on head-Product grade A and B 38 GB/T 32.2-1988 六角头头部带孔螺栓 细杆 B级Hexagon bolts with wire holes on head-Reduced shank-Product grade B 39 GB/T 32.3-1988 六角头头部带孔螺栓 细牙 A和B级Hexagon bolts with wire holes on head-Fine pitch thread-Prod

15、uct grade A and B 40 GB/T 3227-2000 螺栓螺母用装配工具 机动套筒工具的传动四方Assembly tools for screws and nuts-Driving squares for power socket tools 41 GB/T 3228-2000 螺栓螺母用装配工具 冲击式机动四方传动套筒的尺寸Assembly tools for screws and nuts-Machine-operated square drive sockets (impact)-Dimensions 42 GB/T 3229-2000 螺栓螺钉用装配工具 机动螺刀头的

16、六角传动端Assembly tools for bolts and screws-Hexagon drive ends for machine-operated screwdriver bits 43 GB/T 35-1988 小方头螺栓 B级Square head bolts with small head-Product grade B 44 GB/T 3632-1995 钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures 45 G

17、B/T 3633-1995 钢结构用扭剪型高强度螺栓连接副 技术条件Technical requirement for sets of torshear type high strength bolt hexagon nut and plain washer for steel structures 46 GB/T 37-1988 T型槽用螺栓Bolts for T-Slot 47 GB/T 3750.3-1983 卡套式铰接六角螺栓Hollow screws 48 GB/T 5276-1985 紧固件 螺栓、螺钉、螺柱及螺母 尺寸代号和标注Fasteners-Bolts,screws,stu

18、ds and nuts-Symbols and designations of dimensions 49 GB/T 5277-1985 紧固件 螺栓和螺钉通孔Fasteners-Clearance holes for bolts and screws 50 GB/T 5286-2001 螺栓、螺钉和螺母用平垫圈 总方案Plain washers for bolts,screws and nuts-General plan 51 GB/T 5650-1985 扩口式管接头空心螺栓Flared type tube fittings-Inverted flare bolts 52 GB/T 577

19、9.1-2000 紧固件表面缺陷 螺栓、螺钉和螺柱一般要求Fasteners-Surface discontinuities-Bolts,screws and studs for general requirements 53 GB/T 5779.3-2000 紧固件表面缺陷 螺栓、螺钉和螺柱 特殊要求Fasteners-Surface discontinuities-Bolts,screws and studs for special requirements 54 GB/T 5780-2000 六角头螺栓 C级Hexagon head bolts-Product grade C 55 GB

20、/T 5781-2000 六角头螺栓 全螺纹 C级Hexagon head bolts-Full thread-Product grade C 56 GB/T 5782-2000 六角头螺栓Hexagon head bolts 57 GB/T 5783-2000 六角头螺栓 全螺纹Hexagon head bolts-Full thread 58 GB/T 5784-1986 六角头螺栓 细杆 B级Hexagon head bolts-Reduced shank-Product grades B 59 GB/T 5785-2000 六角头螺栓 细牙Hexagon head bolts with

21、 fine pitch thread 60 GB/T 5786-2000 六角头螺栓 细牙 全螺纹Hexagon head bolts with fine pitch thread-Full thread 61 GB/T 5789-1986 六角法兰面螺栓 加大系列 B级Hexagon flange bolts-Heavy series-Product grade B 62 GB/T 5790-1986 六角法兰面螺栓 加大系列 细杆 B级Hexagon flange bolts-Heavy series-Product grade B 63 GB/T 6188-2000 螺栓和螺钉用内六角花

22、形Hexalobular internal driving feature for bolts and screws 64 GB/T 7559-1987 纤维增强塑料层板螺栓连接挤压强度试验方法FRP Laminates-test method for bearing strength by bolted joints 65 GB/T 794-1993 加强半圆头方颈螺栓Strengthened cap head square neck bolts 66 GB/T 798-1988 活节螺栓Eye bolts 67 GB/T 799-1988 地脚螺栓Eyelet bolts 68 GB/T

23、800-1988 沉头双榫螺栓Flat countersunk double nib bolts 69 GB/T 801-1998 小半圆头低方颈螺栓 B级Cup head square neck bolts with small head and short neck-Product grade B 70 GB/T 8-1988 方头螺栓 C级Square head bolts-Product grade C 71 GB/T 8262-1987 圆头椭圆颈螺栓Bolts,round head with oval neck 72 GB/T 892-1986 螺栓紧固轴端挡圈Lock rings

24、 at the end of shaft with bolt 73 GB/T 9074.11-1988 十字槽凹穴六角头螺栓和平垫圈组合件Cross recessed hexagon bolt with indention and plain washer assemblies 74 GB/T 9074.1-2002 螺栓或螺钉和平垫圈组合件Bolt or screw and washer assemblies with plain washers 75 GB/T 9074.12-1988 十字槽凹穴六角头螺栓和弹簧垫圈组合件Cross recessed hexagon bolt with i

25、ndentation and single coil spring lock washer assemblies 76 GB/T 9074.13-1988 十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件Cross recessed hexagon bolt with indentation, single coil lock washer and plan washer assemblies 77 GB/T 9074.15-1988 六角头螺栓和弹簧垫圈组合件Hexagon head bolt and single coil spring lock washer assemblies 78 GB

26、/T 9074.16-1988 六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assemblies 79 GB/T 9074.17-1988 六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt, single coil spring lock washer and plain washer assemblies 螺钉1 GB 3098.7-2000 紧固件机械性能 自挤螺钉Mechanical properties of fasteners-Thread rolling sc

27、rews 2 GB 6560-1986 十字槽盘头自攻锁紧螺钉Cross recessed pan head thread forming screws 3 GB/T 100-1986 开槽沉头木螺钉Slotted countersink head wood screws 4 GB/T 101-1986 开槽半沉头木螺钉Slotted raised countersunk head wood screws 5 GB/T 102-1986 六角头木螺钉Hexagon head wood screws 6 GB/T 10634-1989 螺钉旋具的命名与术语Screwdrivers-Designa

28、tions and nomenclature 7 GB/T 10635-2003 螺钉旋具通用技术条件Screwdrivers-General technical requirements 8 GB/T 10637-1989 一字槽螺钉旋具螺杆Screwdriver blades for slotted head screws 9 GB/T 10638-1989 十字槽螺钉旋具螺杆Screwdriver blades for cross-recessed head screws 10 GB/T 10639-1989 一字槽螺钉旋具Screwdriver for slotted head scr

29、ews 11 GB/T 10640-1989 十字槽螺钉旋具Screwdriver for recessed head screws 12 GB/T 10641-1989 螺旋棘轮螺钉旋具Spiral ratchet screwdriver 13 GB/T 13806.1-1992 精密机械用紧固件 十字槽自攻螺钉 刮削端14 GB/T 13806.2-1992 精密机械用紧固件 十字槽自攻螺钉 刮削端Fasteners for fine mechanics cross recessed tapping screws-Scrape point 15 GB/T 14210-1993 墙板自攻螺钉

30、16 GB/T 15049.7-1996 CAD 标准件图形文件 几何图形和特性规范 螺钉CAD standard parts file-Specification of geometry and parameters-Screws 17 GB/T 15856.1-2002 十字槽盘头自钻自攻螺钉Cross recessed pan head drillig screws with tappiing screw thread 18 GB/T 15856.2-2002 十字槽沉头自钻自攻螺钉Cross recessed countersunk head drilling screws with

31、tapping screw thread 19 GB/T 15856.3-2002 十字槽半沉头自钻自攻螺钉Cross recessed raised countersunk head drilling screws with tapping screw thread 20 GB/T 15856.4-2002 六角法兰面自钻自攻螺钉Hexagon flange head drilling screws with tapping screw thread 21 GB/T 15856.5-2002 六角凸缘自钻自攻螺钉Hexagon washer head drilling screws with tappi