1、思科模拟器命令1. 计算机命令:PCA login: root ;使用root用户password: linux ;口令是linux# shutdown -h now ;同init 0 关机# logout# login# ifconfig ;显示IP地址# ifconfig eth0 netmask ;设置IP地址# ifconfig eht0 netmask down ; 删除IP地址# route add 0.0.0.0 gw # route del 0.0.0.0 gw # route add default gw ;设置网关# route del default gw ;删除网关#
2、route ;显示网关# ping # telnet 2. 交换机支持的命令:交换机基本状态:switch: ;交换机的ROM状态rommon ;路由器的ROM状态hostname ;用户模式hostname# ;特权模式hostname(config)# ;全局配置模式hostname(config-if)# ;接口状态交换机口令设置:switchenable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname ;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令sw
3、itch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 0 4 ;进入虚拟终端switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;
4、删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlanswitch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain ;设置发vtp域名switch(
5、config)#vtp password ;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address ;设置IP地址switch(config)#ip default-gateway ;设置默认网关switch#dir flash: ;查看闪存交换机显示命令:switch#write ;保存配置信息switch#show
6、 vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息3. 路由器支持的命令:路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动路由器口令设置:routerenable ;进入特权模
7、式router#config terminal ;进入全局配置模式router(config)#hostname ;设置交换机的主机名router(config)#enable secret xxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 0 4 ;进入虚拟终端router(config-line)#login ;要求口令验证router(config-line)#password xx ;设置登录
8、口令xxrouter(config)#(Ctrl+z) ; 返回特权模式router#exit ;返回命令路由器配置:router(config)#int s0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置时钟频率router(config-if)#ip address ;设置IP地址router(config-if)#ip address second ;设置第二个IProuter(config-if)#int f0/0.1 ;进入子接口router(confi
9、g-subif.1)#ip address ;设置子接口IProuter(config-subif.1)#encapsulation dot1q ;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#c
10、opy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config ;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommonconfreg 0x2142 ;跳过配置文件rommonconfreg 0x2102 ;恢复配置文件rommonreset ;重新引导rommoncopy xmodem: flash: ;从console传输文件rommonIP_ADDRESS=10.65.1.2 ;设置路由器IPrommonIP_SUBNET_M
11、ASK=255.255.0.0 ;设置路由器掩码rommonTFTP_SERVER=10.65.1.1 ;指定TFTP服务器IPrommonTFTP_FILE=c2600.bin ;指定下载的文件rommontftpdnld ;从tftp下载rommondir flash: ;查看闪存内容rommonboot ;引导IOS静态路由:ip route ;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例动态路由:ro
12、uter(config)#ip routing ;启动路由转发router(config)#router rip ;启动RIP路由协议。router(config-router)#network ;设置发布路由router(config-router)#negihbor ;点对点帧中继用。帧中继命令:router(config)#frame-relay switching ;使能帧中继交换router(config-s0)#encapsulation frame-relay ;使能帧中继router(config-s0)#fram-relay lmi-type cisco ;设置管理类型rou
13、ter(config-s0)#frame-relay intf-type DCE ;设置为DCErouter(config-s0)#frame-relay dlci 16 ;router(config-s0)#frame-relay local-dlci 20 ;设置虚电路号router(config-s0)#frame-relay interface-dlci 16 ;router(config)#log-adjacency-changes ;记录邻接变化router(config)#int s0/0.1 point-to-point ;设置子接口点对点router#show frame p
14、vc ;显示永久虚电路router#show frame map ;显示映射基本访问控制列表:router(config)#access-list permit|deny router(config)#interface ;default:deny anyrouter(config-if)#ip access-group in|out ;defaultut例1:router(config)#access-list 1 deny host 10.65.1.1router(config)#access-list 1 permit anyrouter(config)#int f0/0router(c
15、onfig-if)#ip access-group 4 in例2:router(config)#access-list 4 permit 10.8.1.1router(config)#access-list 4 deny 10.8.1.0 0.0.0.255router(config)#access-list 4 permit 10.8.0.0 0.0.255.255router(config)#access-list 4 deny 10.0.0.0 0.255.255.255router(config)#access-list 4 permit anyrouter(config)#int f
16、0/1router(config-if)#ip access-group 4 in扩展访问控制列表:access-list permit|deny icmp typeaccess-list permit|deny tcp port例1:router(config)#access-list 101 deny icmp any 10.64.0.2 0.0.0.0 echorouter(config)#access-list 101 permit ip any anyrouter(config)#int s0/0router(config-if)#ip access-group 101 in例2:r
17、outer(config)#access-list 102 deny tcp any 10.65.0.2 0.0.0.0 eq 80router(config)#access-list 102 permit ip any anyrouter(config)#interface s0/1router(config-if)#ip access-group 102 out删除访问控制例表:router(config)#no access-list 102router(config-if)#no ip access-group 101 in路由器的nat配置Router(config-if)#ip n
18、at inside ;当前接口指定为内部接口Router(config-if)#ip nat outside ;当前接口指定为外部接口Router(config)#ip nat inside source static p portRouter(config)#ip nat inside source static 10.65.1.2 60.1.1.1Router(config)#ip nat inside source static tcp 10.65.1.3 80 60.1.1.1 80Router(config)#ip nat pool p1 60.1.1.1 60.1.1.20 255
19、.255.255.0Router(config)#ip nat inside source list 1 pool p1Router(config)#ip nat inside destination list 2 pool p2Router(config)#ip nat inside source list 2 interface s0/0 overloadRouter(config)#ip nat pool p2 10.65.1.2 10.65.1.4 255.255.255.0 type rotaryRouter#show ip nat translationrotary 参数是轮流的意
20、思,地址池中的IP轮流与NAT分配的地址匹配。overload参数用于PAT 将内部IP映射到一个公网IP不同的端口上。外部网关协议配置routerA(config)#router bgp 100routerA(config-router)#network 19.0.0.0routerA(config-router)#neighbor 8.1.1.2 remote-as 200配置PPP验证:RouterA(config)#username password RouterA(config)#int s0RouterA(config-if)#ppp authentication chap|pap
21、4PIX防火墙命令Pix525(config)#nameif ethernet0 outside security0 ;命名接口和级别Pix525(config)#interface ethernet0 auto ;设置接口方式Pix525(config)#interface ethernet1 100full ;设置接口方式Pix525(config)#interface ethernet1 100full shutdownPix525(config)#ip address inside 192.168.0.1 255.255.255.0Pix525(config)#ip address o
22、utside 133.0.0.1 255.255.255.252Pix525(config)#global (if_name) natid ip-ip ;定义公网IP区间Pix525(config)#global (outside) 1 7.0.0.1-7.0.0.15 ;例句Pix525(config)#global (outside) 1 133.0.0.1 ;例句Pix525(config)#no global (outside) 1 133.0.0.1 ;去掉设置Pix525(config)#nat (if_name) nat_id local_ip netmarkPix525(con
23、fig)#nat (inside) 1 0 0内网所有主机(0代表0.0.0.0)可以访问global 1指定的外网。Pix525(config)#nat (inside) 1 172.16.5.0 255.255.0.0内网172.16.5.0/16网段的主机可以访问global 1指定的外网。Pix525(config)#route if_name 0 0 gateway_ip metric ;命令格式Pix525(config)#route outside 0 0 133.0.0.1 1 ;例句Pix525(config)#route inside 10.1.0.0 255.255.0.
24、0 10.8.0.1 1 ;例句Pix525(config)#static (inside, outside) 133.0.0.1 192.168.0.8表示内部ip地址192.168.0.8,访问外部时被翻译成133.0.0.1全局地址。Pix525(config)#static (dmz, outside) 133.0.0.1 172.16.0.8中间区域ip地址172.16.0.8,访问外部时被翻译成133.0.0.1全局地址。 1. switch配置命令(1)模式转换命令用户模式-特权模式,使用命令enable特权模式-全局配置模式,使用命令config t全局配置模式-接口模式,使用
25、命令interface+接口类型+接口号全局配置模式-线控模式,使用命令line+接口类型+接口号注:用户模式:查看初始化的信息.特权模式:查看所有信息、调试、保存配置信息全局模式:配置所有信息、针对整个路由器或交换机的所有接口接口模式:针对某一个接口的配置线控模式:对路由器进行控制的接口配置(2)配置命令show running config 显示所有的配置show versin 显示版本号和寄存器值shut down 关闭接口no shutdown 打开接口ip add +ip地址 配置IP地址secondary+IP地址 为接口配置第二个IP地址show interface+接口类型+接
26、口号 查看接口管理性show controllers interface 查看接口是否有DCE电缆show history 查看历史记录show terminal 查看终端记录大小hostname+主机名 配置路由器或交换机的标识config memory 修改保存在NVRAM中的启动配置exec timeout 0 0 设置控制台会话超时为0service password-encryptin 手工加密所有密码enable password +密码 配置明文密码ena sec +密码 配置密文密码line vty 0 4/15 进入telnet接口password +密码 配置telnet密
27、码line aux 0 进入AUX接口password +密码 配置密码line con 0 进入CON接口password +密码 配置密码bandwidth+数字 配置带宽no ip address 删除已配置的IP地址show startup config 查看NVRAM中的配置信息copy run-config startup config 保存信息到NVRAMwrite 保存信息到NVRAMerase startup-config 清除NVRAM中的配置信息show ip interface brief 查看接口的谪要信息banner motd # +信息 + # 配置路由器或交换机
28、的描素信息description+信息 配置接口听描素信息vlan database 进入VLAN数据库模式vlan +vlan号+ 名称 创建VLANswitchport access vlan +vlan号 为VLAN为配接口interface vlan +vlan号 进入VLAN接口模式ip add +ip地址 为VLAN配置管理IP地址vtp+service/tracsparent/client 配置SW的VTP工作模式vtp +domain+域名 配置SW的VTP域名vtp +password +密码 配置SW的密码switchport mode trunk 启用中继no vlan
29、+vlan号 删除VLANshow spamming-tree vlan +vlan号 查看VLA怕生成树议2. 路由器配置命令ip route+非直连网段+子网掩码+下一跳地址 配置静态/默认路由show ip route 查看路由表show protocols 显示出所有的被动路由协议和接口上哪些协议被设置show ip protocols 显示了被配置在路由器上的路由选择协议,同时给出了在路由选择协议中使用的定时器 等信息router rip 激活RIP协议network +直连网段 发布直连网段interface lookback 0 激活逻辑接口passive-interface +接口类型+接口号 配置接口为被动模式 debug ip +协议 动态查看路由更新信息undebug all 关闭所有DEBUG信息router eigrp +as号 激活EIGRP路由协议network +网段+子网掩码 发布直连网段show ip eigrp neighbors 查看邻居表show ip eigrp topology 查看拓扑表show ip eigrp traffic 查看发送包数量router ospf +process-ID 激活OSPF协议network+直连网段+area+区域号 发布直连网段show ip ospf 显示OSPF的
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1