3GPP TS 25143 V900 12.docx

1、3GPP TS 25143 V900 123GPP TS 25.143 V9.0.0 (2009-12)Technical Specification3rd Generation Partnership Project;Technical Specification Group Radio Access Network;UTRA repeater conformance testing(Release 9)The present document has been developed within the 3rd Generation Partnership Project (3GPP TM)

2、 and may be further elaborated for the purposes of 3GPP. The present document has not been subject to any approval process by the 3GPP Organisational Partners and shall not be implemented. This Specification is provided for future development work within 3GPP only. The Organisational Partners accept

3、 no liability for any use of this Specification.Specifications and reports for implementation of the 3GPP TM system should be obtained via the 3GPP Organisational Partners Publications Offices.KeywordsUMTS, radio, repeater3GPPPostal address3GPP support office address650 Route des Lucioles Sophia Ant

4、ipolisValbonne FRANCETel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16Internethttp:/www.3gpp.orgCopyright NotificationNo part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media. 2009, 3GPP Organizational Partners

5、(ARIB, ATIS, CCSA, ETSI, TTA, TTC).All rights reserved.UMTS is a Trade Mark of ETSI registered for the benefit of its members3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational PartnersLTE is a Trade Mark of ETSI currently being registered for the be

6、nefit of its Members and of the 3GPP Organizational PartnersGSM and the GSM logo are registered and owned by the GSM AssociationContents1 Scope 62 References 63 Definitions, symbols and abbreviations 73.1 Definitions 73.2 (void) 73.3 Abbreviations 74 Frequency bands and channel arrangement 84.1 Freq

7、uency bands 84.2 TX RX frequency separation 84.3 Channel arrangement 94.3.1 Channel spacing 94.3.2 Channel raster 94.3.3 Channel number 95 General test conditions and declarations 105.1 Acceptable uncertainty of Test System 105.1.1 Measurements of test environments 115.1.2 Measurements of Repeater 1

8、25.2 Repeater test tolerances (informative) 135.3 Interpretation of measurement results 135.4 Test Environment 145.4.1 Normal test environment 145.4.2 Extreme test environment 145.4.2.1 Extreme temperature 145.4.3 Vibration 155.4.4 Power supply 155.5 Selection of configurations for testing 155.6 Reg

9、ional requirements 165.7 Test Models 175.8 Format and interpretation of tests 175.9 Repeater configurations 185.9.1 Power supply options 185.9.2 Combining of Repeaters 186 Output power 186.1 Maximum output power 186.1.1 Definition and applicability 186.1.2 Minimum Requirements 186.1.3 Test purpose 1

10、96.1.4 Method of test 196.1.4.1 Initial conditions 196.1.4.2 Procedure 196.1.5 Test Requirements 197 Frequency stability 207.1 Definition and applicability 207.2 Minimum Requirement 207.3 Test purpose 207.4 Method of test 207.4.1 Initial conditions 207.4.2 Procedure 217.5 Test requirements 218 Out o

11、f band gain 218.1 Definitions and applicability 218.2 Minimum Requirements 218.3 Test purpose 228.4 Method of test 228.4.1 Initial conditions 228.4.2 Procedure 228.5 Test requirements 229 Unwanted emission 229.1 Out of band emission 239.1.1 Void 239.1.2 Operating band unwanted emissions 239.1.2.1 De

12、finitions and applicability 239.1.2.2 Minimum Requirements 239.1.2.3 Test purpose 269.1.2.4 Method of test 269.1.2.4.1 Initial conditions 269.1.2.4.2 Procedures 269.1.2.5 Test requirements 269.1.3 Protection of BS receiver in the operating band 289.1.3.1 Minimum Requirement 299.1.4 Co-existence with

13、 services in adjacent frequency bands 299.1.4.1 Minimum requirement 299.2 Spurious emissions 299.2.1 Definition and applicability 299.2.2 Minimum Requirements 309.2.2.1 Spurious emission (Category A) 309.2.2.2 Spurious emission (Category B) 309.2.2.3 Void 319.2.2.4 Co-existence with other systems in

14、 the same geographical area 319.2.2.4.1 Minimum Requirements 329.2.2.5 Co-existence with co-located and co-sited base stations 339.2.2.5.1 Minimum Requirements 349.2.2.6 Co-existence with PHS 359.2.2.6.1 Minimum requirement 359.2.2.7 Co-existence with UTRA-TDD 359.2.2.7.1 Operation in the same geogr

15、aphic area 359.2.2.7.2 Co-located Repeaters and UTRA-TDD base stations 369.2.2.8 (Void) 389.2.2.9 Protection of public safety operations 389.2.2.9.1 Minimum Requirement 389.2.3 Test purpose 389.2.4 Method of test 389.2.4.1 Initial conditions 389.2.4.2 Procedures 389.2.5 Test requirements 3910 Modula

16、tion accuracy 3910.1 Error vector magnitude 3910.1.1 Definition and applicability 3910.1.2 Minimum Requirements 3910.1.3 Test purpose 3910.1.4 Method of test 3910.1.4.1 Initial conditions 3910.1.4.2 Procedure 3910.1.4.3 Stimulus EVM effect 3910.1.5 Test requirements 4010.2 Peak code domain error 401

17、0.2.1 Definition and applicability 4010.2.2 Minimum Requirements 4010.2.3 Test purpose 4010.2.4 Method of test 4010.2.4.1 Initial conditions 4010.2.4.2 Procedure 4010.2.5 Test requirements 4011 Input intermodulation 4011.1 Definition and applicability 4111.2 Minimum Requirements 4111.2.1 General req

18、uirement 4111.2.2 Co-location with BS in other systems 4111.2.3 Co-existence with other systems 4311.3 Test purpose 4511.4 Method of test 4511.4.1 Initial conditions 4511.4.2 Procedure 4511.5 Test requirements 4511.5.1 Mandatory requirement 4511.5.2 Co-location with BS in other systems 4611.5.3 Co-e

19、xistence with other systems 4812 Output intermodulation 5012.1 Definition and applicability 5012.2 Minimum requirement 5012.3 Test purpose 5012.4 Method of test 5012.4.1 Initial conditions 5012.4.2 Procedures 5012.5 Test requirements 5113 Adjacent Channel Rejection Ratio (ACRR) 5113.1 Definitions an

20、d applicability 5113.2 Minimum Requirements 5113.3 Test purpose 5113.4 Method of test 5213.4.1 Initial conditions 5213.4.2 Procedure 5213.4.3 Test Requirements 52Annex A (informative): Repeater measurement system set-up 53A.1 Maximum output power 53A.2 Frequency stability 53A.3 Out of band gain 53A.

21、4 Unwanted emission: Spectrum emission mask 53A.5 Unwanted emission: Spurious emission 54A.6 Modulation Accuracy: Error Vector Magnitude 54A.7 Modulation Accuracy: Peak Code Domain Error 54A.8 Input inter modulation 55A.9 Output Intermodulation 55Annex B (informative): Derivation of Test Requirement

22、s 56Annex C (informative): Acceptable uncertainty of Test Equipment 58Annex D (informative): Change History 59ForewordThis Technical Specification has been produced by the 3rd Generation Partnership Project (3GPP).The contents of the present document are subject to continuing work within the TSG and

23、 may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows:Version x.y.zwhere:x the first digit:1 presented to TSG for information;2 p

24、resented to TSG for approval;3 or greater indicates TSG approved document under change control.Y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc.z the third digit is incremented when editorial only changes have been incorporated in

25、 the document.1 ScopeThe present document specifies the Radio Frequency (RF) test methods and Minimum Requirements for UTRA FDD Repeaters. These have been derived from, and are consistent with the UTRA FDD Repeater specifications defined in TS 25.106.This document establishes the minimum RF characte

26、ristics of the UTRA FDD Repeater.2 ReferencesThe following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or nonspecific. For a

27、 specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the pre

28、sent document. 1 3GPP TS 25.104: “UTRA(BS) FDD; Radio transmission and Reception”.2 3GPP TS 25.942: ”RF system scenarios”.3 3GPP TS 25.113: Base station EMC.4 ITU-R recommendation SM.329: “Unwanted emissions in the spurious domain “.5 ITU-T recommendation O.153: “Basic parameters for the measurement

29、 of error performance at bit rates below the primary rate”.6 IEC 60721-3-3 (1994): “Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 3: Stationary use at weather protected locations”.7 IEC 60721-3-4 (1995): “Classifi

30、cation of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 4: Stationary use at non-weather protected locations”.8 IEC 60068-2-1 (1990): “Environmental testing Part 2: Tests. Tests A: Cold”.9 IEC 60068-2-2 (1974): “Environmental testi

31、ng Part 2: Tests. Tests B: Dry heat”.10 IEC 60068-2-6 (1995): “Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal)”.11 3GPP TS 25.141: “Base station conformance testing (FDD)”.12 3GPP TS 25.106: “UTRA Repeater; Radio transmission and reception”.13 3GPP TS 36.143: “Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater conformance testing”3 Definitions, symbols and abbreviations3.1 DefinitionsFor the purposes of the present document, the following terms