港机重工专业英语.docx

1、港机重工专业英语结构焊接专业英语General 通用美国海湾大桥San Francisco Oakland Bay BridgeAB/F公司American Bridge/FLUOR JV法规，规范code 标准standard暂行标准tentative standard技术规程specification要求requirement细则regulation法律law条款provision总则general provision约定条件stipulation合同规定on the stipulation that合同contract签订合同sign a contract拟订合同draw up a co

2、ntract代理人mandatory条件condition符合conform to (with)遵守comply with确认confirm证书certificate认可approve (v), approval (n.)接收accept (v.), acceptable (adj.)评定qualify (v.) qualification (n.)满足meet许可permit拒收reject 废品rejection鉴别identify提交submit to论证demonstrate公约convention仲裁arbitration业主代表representative of owner业主ow

3、ner委托人client签署sign要求request监理员supervisorsupvaz, surveyor检查鉴定survey检查inspect, check, 验证verify目击，见证witness禁止prohibit建议recommend满意的satisfactory授权authorize文件document审查review监控monitor测定detect参考规范referencing code制造商manufacturer位置纠正和预防措施LocationCorrective And Preventive Action报告report不符合报告Non-conformation

4、Report(NCR)火工校正报告Heat Straightening Report(HSR)美国焊接协会American Welding Society(AWS)生产日报告Daily Production Report焊缝返修报告Welding Repair Report(WR)关键焊缝返修报告Critical Welding Repair Report(CWR)无损检测non destructive test(NDT)探伤申请表Application Form For NDT焊接工艺技术规程Welding Procedure Specification(WPS)钢材试验报告Mill Tes

5、t Report(MTR)工艺评定记录Procedure Qualification Report(PQR)逐个检验individual inspection抽样检验sampling inspection, cross check评价evaluate实验experiment试样specimen可跟踪性traceability预先具有资格prequalify判定，评价judge责任responsibility, obligation, duty官方，管理局authority样本sample保证assure通知单notification通知notify (v.) notice (n.)会议纪要mi

6、nutes数量quantity质量quality质量控制quality control(Q.C)质量保证quality assurance(Q.A)缺陷defect损坏damage易断裂危险的（通译：关键）critical关键焊缝返修critical welding repair停止点hold point(H)交货delivery原始记录original record批注comment开始commence答复reply紧急urgent直线度straightness垂直度perpendicular平整度flatness随机的random不平uneven表面粗糙度surface roughness

7、报验通知单Notification for inspection澄清单Clarify技术澄清单clarification to the specification尺寸dimension 长度length宽度width高度height厚度thickness深度depth跨度span直径diameter半径radius尺寸公差dimension tolerance允许误差admissible error中心线偏斜lack of alignment斜度slope角度angle对角线diagonal平行线parallel中心线center line斜线oblique line切线tangential

8、line轮廓线contour line原点，起点original 指标index方向direction指南guide选定choose选择select挑选pick炉批号heat / plate number炉、批lot or heat图纸drawing工程师engineer签发sign & issue执行performance中标success of bid询价inquiry不相符non-conformance遗漏omission去掉remove修补repair型号model暂时的temporarily测量measure附件attachment修正amend, correct型材bar stoc

9、k湿气Moisture, humidity发出issue填写fill in间距interval承包商contractor分包商subcontractor供货商supplier操作错误operate missing抗拉强度tensile strength屈服强度yield strength游标卡尺Vernier caliper外径千分尺external micrometer内径千分尺internal micrometer红外线测温仪infrared ,nfrrd thermometer油漆测厚仪coating thickness gauge焊角尺welding inspection ruler硬

10、度计Leeb hardness tester超声波测厚仪ultrasonic thickness meter钢卷尺table测量范围Range rend分度值Scale skel探伤test无损检测nondestructive testing (NDT)外观检测Visual testing (VT)超声波探伤ultrasonic testing (UT)射线探伤radiographic testing (RT)磁粉探伤magnetic particle testing (MT)渗透探伤penetrant testing (PT)外观检查visual examination 读数,指示indic

11、ation(UT)侵蚀erosion变形distortion试运行trial operation永久变形permanent deformation超出beyond ，exceed失败，故障failure不合格的不连续性（常意译：缺陷）unacceptable discontinuity（defect）裂缝crack工艺procedure加工process, working工艺单technical note工艺技术technique工艺的technical工位station, position车间shop, workshop工厂mill, factory, manufacturer工地、现场si

12、te外场yard, field侧面side断面section水平基准线horizontal reference line精度accuracy余量allowance包装package焊接 Welding焊件weldment缺陷defect母材base weld填充金属filler metal熔化fusion熔透penetration完全熔合complete fusion完全熔透complete penetration接头完全熔透complete joint penetration(CJP)接头部分熔透partial joint penetration(PJP)对接接头butt joint对接焊b

13、utt welding角焊fillet welding搭接焊lap welding塞焊plug welding平焊down hand welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding平角焊horizontal fillet welding仰角焊fillet welding in the overhead衬垫焊welding with backing 单面焊双面成形one-side welding with back

14、formation定位焊缝tack weld临时焊缝temporary weld堆焊surfacing返修焊rewelding补焊repair welding手工焊manual welding半自动焊Semi-matic welding自动焊automatic welding药皮焊条电弧焊shielded metal arc welding(SMAW)埋弧焊submerged arc welding(SAW)保护气体shielded gas气体保护电弧焊gas metal arc welding(GMAW)CO2气保焊carbon-dioxide arc welding 药芯焊丝电弧焊flux

15、 cored arc welding(FCAW)药芯焊丝电弧焊-气体保护flux cored arc welding-gas shielded (FCAW-G)药芯焊丝电弧焊-自保护flux cored arc welding-self shielded (FCAW-S)单面焊welding by one side双面焊welding by both sides单道焊single pass welding多道焊multi-pass welding单层焊single layer welding多层焊 multi-layer welding连续焊continuous welding断续焊inter

16、mittent welding打底焊backing welding坡口groove坡口面groove face坡口面角度level angle, bevel angle坡口角度groove angle 坡口高度groove depth钝边root face钝边高度thickness of root face根部间隙root gap根部半径root radiusI型坡口square groove焊缝表面weld face焊缝背面back of weld打底焊缝backing weld焊缝尺寸size of weld焊缝厚度throat thickness熔深depth of fusion焊缝成形

17、appearance of weld余高reinforcement背面余高root reinforcement焊脚leg焊根weld root焊趾weld toe保留垫板permanent临时垫板temporary backing垫板backing铜垫板copper backing焊剂垫flux backing引弧板run-on tab end tab引出板run-off tab end tab 引弧arc start, arc burning熄弧arc outage, arc blowout焊接工艺评定welding procedure qualification(WPQ)焊接工艺规程wel

18、ding procedure specification(WPS)焊接工艺参数welding parameter焊接电流welding current交流电流alternating current直流电流direct current电弧电压arc voltage焊接速度weld travel speed预热preheat后热postheat预热温度preheat temperature焊道pass道间温度interpass temperature焊后热处理post weld heat treatment焊接环境welding surroundings焊工考试welder qualificati

19、on test焊工证书welder certification焊接顺序welding sequence清根back gouging清渣slag removal焊缝清理weld cleaning中间焊层intermediate weld layer划线mark 焊接缺陷weld defect裂纹crack咬边undercut焊瘤overlap烧穿burn through熔渣slag 夹渣slag inclusion飞溅spatter气孔pore密集气孔porosity未焊透incomplete penetration未熔合incomplete fusion未焊满Incompletely fill

20、ed weld麻点pock凹坑pit电弧擦伤arc scratch, arc strike层状撕裂lamellar tearing挂渣adhering slag结瘤dross变形distortion , deformation弧坑crater错边dislocation, mismatching, misalignment收缩shrinkage焊缝穿越孔weld access hole热影响区heat-affected zone (HAZ)校正straighten校火Heat straightening焊缝成形差rough weld边缘不平整rough edge剥落peel焊接材料welding

21、 consumables焊条electrode酸性焊条acid electrode碱性焊条basic electrode低氢焊条low hydrogen type electrode焊剂welding flux焊丝welding wire药心焊丝flux-cored wire电弧焊机arc welding machine弧焊电源arc welding power source焊条保温筒thermostat for electrode干燥箱dryer胎架placenta压缩空气compressed air打磨grind (ground)焊钳electrode holder砂轮机grinder钢丝

22、刷wire brush砂纸sand-paper气焊gas welding氧-乙炔焊oxy-acetylene welding 气割gas cutting氧气切割oxygen cutting(OC)电弧切割arc cutting数控切割NC cutting电弧刨槽arc gouging碳弧气刨carbon arc air gouging焊接熔池weld pool冲砂abrasive blasting油脂 grease污染物contaminant内部，外部interior, exterior部件 member构件,部件member, component零件part, element组件assemb

23、ly分装件Sub-assembly装置device机械machinery机械零件mechanical element模型mock-up箱体assembly box面板skin A面板Skin A双层板(A面)Double plate（face A）隔板diaphragm隔板组件Diaphragm Assembly下层隔板组件Bottom Diaphragm Sub-Assembly上层隔板组件Top Diaphragm Sub-Assembly下层横隔板法兰组件Bottom Diaphragm Flange plate Sub-Assembly上层横隔板法兰组件Top Diaphragm Fl

24、ange plate Sub-Assembly下层横隔板Bottom Diaphragm plate上层横隔板Top Diaphragm plate双层隔板Double diaphragm横隔板嵌补板Diaphragm FLG Plate腹板Web plate筋板stiffener斜筋板Diagonal Stiffener纵向筋Longitudinal Stiffener纵向筋连接板Longitudinal stiff splice plate横梁罩壳筋板Strut faade stiffener plate横梁罩壳,支撑罩壳Strut faade plate联系梁，横梁Strut plate

25、横梁罩壳槽钢Strut faade channel槽钢Channel罩壳密封角钢Faade sealing angle座板Riser plate三角板Triangular plate加强圈plange横隔板加强圈Diaphragm edge plate定位板Fit Lug Plate人孔密封板Access opening sealing plate人孔门板Access opening door plate人孔门铰链Access opening door hing转向板Deflector plate盖板Cover plate联系梁支撑Strut plate外连接板exterior splice

26、plate内连接板interior splice plate内连接板垫板Interior splice Shim plate内角连接板Interior corner splice plate十字撑Cross bracing plate十字撑三角板Cross brace gusset plate吊耳lifting lug模型装配图MOCK-UP Erection DiagramU-肋U-rib从动车架Idler Carriage平衡梁Equalizer beam主动车架Driving Carriage上架结构 /下架结构Headblock/down structure顶升支撑架Jack Up S

27、upport伸缩架telescopic beam横梁结构cargo beam滑轮架/箱sheave rack/box联系架link rack底梁主结构main beam箱型梁box-shape beam端梁end beam伸梁extensile beam预投件standard parts固定架fixed supporter回转架rotary supporter吊架rack台车架Bogie上架锚定架Anchoring support吊钩横梁Hook beam转销箱Twistlock box转销结构twistlock beam移动架movable frame组合件subassembly输缆（管）装置cable and hose carrier伸缩平移驱动机构telescopic drive system中间吊点装置