汽车专业英语词汇1.docx

1、汽车专业英语词汇1 汽车专业英语词汇(1)汽车专业英语词汇(1)汽车专业英语词汇(1)轮椅升降机 wheel chair lift 图例 legend 工位 station 吊运装置 overhead hoist 更衣室 restroom 1号厂房工艺布置方案图 proposal of the plant i layout 合笼 mate 底盘平移台 chassis shuttle 车辆转移台 bus transfer 前围角板 front wall angle cover 后围侧板 rear wall side cover 保险杠 bumper 三类底盘 three type chassis

2、 左侧围应力蒙皮 r/s stretching skin (road side) 中涂 floating coat 拼装台 collector 切割轮口 wheel -arch cutting 内饰 trim 线束 harness 返工 re-doing 轮罩护板 wheel house 发车前准备 pre-delivery 举升 hoist 小批量产品 be pilot 2 套 two kits 配电站 power transformer substation 裙板 skirt 发动机托架 engine holding frame 诊断报警系统 diagnosis and alarming

3、system 互换性 interchangeability 缩微图纸 microfiche files 总装 final assembly 磷化 phosphating 仪表板 dash board 切齐 trimming 结构完整性 structure integrity 自动愈合的防腐材料 self-healing corrosion preventative material 长途客车 inter-city bus 改装厂 refitting factory 遮阳板 sun visor 随车工具 tool box 钢化玻璃 toughened grass 异形钢管 special ste

4、el pipe 全天候空调系统 full range a/c 强制通风 ram-air ventilation 停机时间 downtime 无公害柴油 clean diesel 宽敞悬臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 织物纹里铝合金 textured aluminum extrution 爬坡能力 grade ability 排水阀 drain valve 除湿器 moisture ejector 怠速时 at idle 琴式驱动桥 banjo type drive axle 通风口 duct 恒温控制 thermostatic c

5、ontrol 平衡水箱 surge tank 变光开关 simmer switch 消音器 muffler 防破坏 vandal resistant 聚碳化透镜 poly-carbonate len 镀锌板 galvanized plate 搭接 lap 亮丽的外表 smart apperance 隐藏式固定 concealed fastening 水洼 ponding 发动机中置式客车 bus with under floor engine 组合式客车车身 modular bus body 薄壳式结构 shell construction 衬垫 pad 空气导流板 air deflector

6、 搁梁 shelf beam 腰梁 waist rail 梭梁 stabilizing beam 腰带式安全带 diagonal safety belt 压条 trim strip 嵌条 insertion strip 翼板 fender 斜撑 bracing piece 转向盘回正性试验 test of steering wheel returnability转向盘转角脉冲试验 steering wheel impulse input test转向盘转角阶跃输入试验 steering wheel step input or transient state yaw response test极

7、限侧向加速度试验 limiting lateral acceleration test汽车平顺性随机输入行驶试验 automobile ride random input running test汽车平顺性单脉冲输入行驶试验 automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验 measurement of natural frequency and damping raito of suspension功率突然变化影响试验 test of effect of sudden power change收油门后控制试验

8、 test of control at breakway横风稳定性试验 test of crosswind stability反冲试验 kick-back test轮胎爆破响应时间试验 test of burst response of tyre绕过障碍物试验 obstacle avoidance test移线试验 lane change testj型转弯试验 test of j turn频率响应时间试验 frequency response test瞬态响应时间试验 transient response test阶路响应时间试验 step response test脉冲响应试验 pulse

9、response test静态操舵力试验 static steering effort test悬架举升试验 jack-up test of suspension耐翻倾试验 test of overturning immunity轮辋错动试验 rim slip test风洞试验 wind tunnel test制动稳定性试验 test of braking stability最小转弯直径试验 minimum turning diameter test操舵力试验 steering effort test类型 type发动机 engine内燃机 intenal combusiton engine动

10、力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发动机 compression ignition engine往复式内燃机 reciprocating internal combustion engine化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程

11、发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机 water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多

12、种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 multiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀

13、式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead cams

14、haft enginev形发动机 v-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical enginew形发动机 w-enginei形发动机 i-enginel形发动机 l-enginef形发动机 f-engine性能 performance二冲程循环 two-stroke cycle四冲程循环 four-strok

15、e cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆

16、炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程 expansion-exchange stroke换气压缩行程 exchange-compression stroke止点 dead center上止点 top dead center(upper dead center)下止点 lower dead center(bottom dead center)上止点前 budc(before upper dead center)上止点后 atdc(after top dead cetn

17、er)下止点前 bbdc(before bottom dead center)下止点后 abdc(after bottom dead center)缸径 cylinder bore缸径与行程 bore and stroke空气室 energy chamber气缸余隙容积 cylinder clearance volume燃烧室容积 combustion chamber volume气缸最大容积 maximum cylinder volume压缩室 compression chamber排气量 displacement发动机排量 engine displacement活塞排量 piston sw

18、ept volume气缸容量 cylinder capacity单室容量 single-chamber capacity容积法 volumetry压缩比 compression ratio临界压缩比 critical compression ratio膨胀比 expansion ratio面容比 surface to volume ratio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力 brake mean effective pressure(bmep)空燃比 air fuel ratio燃

19、空比 fuel air ratio燃料当量比 fuel equivalence ratio扭矩 torque单缸功率 power per cylinder升功率 power per liter升扭矩 torque per liter升质量 mass per liter 减额功率 derating power输出马力 shaft horsepower马力小时，马力时 horsepower-hour总马力 gross horse power总功率 gross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consum

20、ption空气消耗率 air consumption机油消耗量 oil consumption有效马力 net horse power额定马力 rated horse power马力重量系数 horsepower-weight factor制动功率 brake horse power制动热效率 brake thermal efficiency 总效率 overall efficiency排烟极限功率 smoke limiting horsepower功率曲线 power curve机械损失 mechanical loss机械效率 mechanical efficiency有效热效率 effec

21、tive thermal efficiency充气系数 volumetric efficiency过量空气系数 coefficient of excess air适应性系数 adaptive coefficient扭矩适应性系数 coefficient of torque adaptibility转速适应性系数 speed adaptive coefficient强化系数 coefficient of intensification校正系数 correction factor换算系数 conversion factor活塞平均速度 mean piston speed发动机转速 engine s

22、peed (rotational frequency)怠速转速 idling speed经济转速 economic speed起动转速 starting speed最低稳定工作转速 lowest continuous speed with load最大扭矩转速 speed at maximum torque最高空转转速 maximum no load governed speed调速 speed governing 超速 overspeed怠速 idling转速波动率 speed fluctuation rate工况 working condition(operating mode)额定工况

23、declared working condition变工况 variable working condition稳定工况 steady working condition空载 no-load全负荷 full load超负荷 overload部分负荷 part load充量（进气）charge旋转方向 direction of rotation顺时针 clockwise逆时针 counter-clockwise左转 left-hand rotation右转 right-hand rotation外径 major diameter中径 pitch diameter内径 minor diameter

24、径向间隙 radial clearance发动机性能 engine performance加载性能 loading performance起动性能 starting performance加速性能 acceleration performance动力性能 power performance排放性能 emission performance空转特性 no load characteristics负荷特性 part throttle characteristics调速特性 governor control characteristics万有特性 mapping characteristics稳定调

25、速率 steady state speed governing rate气缸体和气缸盖 cylinder block and head气缸体 cylinder block整体铸造 cast inblock (cast enblock)发动机罩 engine bonnet气缸体加强筋 engine block stiffening rib气缸 cylinder（转子机）缸体 stator缸径 cylinder bore气缸体机架 cylinder block frame气缸盖 cylinder head配气机构箱 valve mechanism casing气缸体隔片 cylinder spac

26、er气缸盖密封环 cylinder head ring gasket气缸盖垫片 cylinder head gasket气缸套 cylinder liner(cylinder sleeve)干式缸套 dry cylinder liner湿式缸套 wet cylinder liner气缸水套 water jacket膨胀塞 expansion plug防冻塞 freeze plug气缸壁 cylinder wall环脊 ring ridge排气口 exhaust port中间隔板 intermediate bottum导板 guideway创成半径（转子机）generating radius缸体

27、宽度（转子机）operating width机柱 column燃烧室 combustion chamber主燃烧室 main combustion chamber副燃烧室 subsidiary combustion chamber预燃室 prechamber涡流燃烧室 swirl combustion chamber分开式燃烧室 divided combustion chamber涡流式燃烧室 turbulence combustion chamber半球形燃烧室 hemispherical combustion chamber浴盆形燃烧室 bathtub section combustion

28、 chamberl形燃烧室 l-combustion chamber楔形燃烧室 wedge-section combustion chamber开式燃烧室 open combustion chamber封闭喷射室 closed spray chamber活塞顶内燃烧室 piston chamber爆发室 explosion chamber燃烧室容积比 volume ratio of combustion cahmber燃烧室口径比 surface-volume ratio of combustion chamber通道面积比 area ratio of combustion chamber p

29、assage曲轴箱通气口 crankcase breather凸轮轴轴承座 camshaft bearing bush seat定时齿轮室罩 camshaft drive(gear)cover曲轴箱检查孔盖 crankcase door曲轴箱防爆门 crankcase explosion proof door主轴承盖 main bearing cap气缸盖罩 valve mechanism cover飞轮壳 flywheel cover扫气储器 scavenging air receiver活塞 piston裙部开槽活塞 split skirt pistonu形槽活塞 u-slot pisto

30、n滚花修复活塞 knurled piston圆顶活塞 dome head piston平顶活塞 flat head piston凸顶活塞 crown head piston(convex head piston)凹顶活塞 concave head piston阶梯顶活塞 step-head piston筒形活塞 trunk piston椭圆形活塞 oval piston抗热变形活塞 autothermic piston不变间隙活塞 constant clearance piston镶因瓦钢片活塞 invar strut piston直接冷却式活塞 direct-cooled piston间接冷却式活塞 indirect cooled piston滑裙活塞 slipper piston活塞速度 piston speed活塞顶部 piston head活塞裙部 piston skirt整体活塞裙 solid skirt活塞裙扩大衬簧 piston skirt expander滑履式活塞裙 slipper skirt隔热槽 heat dam活塞标记 piston mark活塞销 piston pin活塞销孔 piston pin boss活塞销衬套 pi