角钢钢材检测报告.docx

1、角钢钢材检测报告钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造有限公司 报告编号 B831a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B831a 委托单位 无锡明阗通用设备制造有限公司 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Constructi

2、on unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel section Testing environment: 20OC In

3、spection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论 Test conclusionQ235B0.160.480.290.0400.025该样品经检验，按GB/T706-2008标准评定：化学成分分析合格After the sample inspection, the analysis of chemical composition is acceptable in accordance with GB/T706-

4、2008 Standard.牌号Marks规格Specification（mm）计算重量Calculated weight（t）拉伸弯曲试验Bending Test（180O）代表数量Representative quantity（t）生产厂家Manufacturer质保书编号Warranty number结构部位 Sructural part检测结论Test conclusion屈服点sYield points（MPa）抗拉强度bTensile Strengthb（MPa）伸长率5Elongation5（%）Q235BL50502.52704203227.52.5马鞍山钢铁股份有限公司Maa

5、nshan Iron & Steel Co., LtdZ23060950005烟风道Flue and air duct该样品经检验，按GB/T706-2008标准评定：机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明：1.若对报告有异议，应于收到报告之日期起十五日内，以书面形式向检测单位提出，逾期视为对报告无异议。 2.送样检测，检

6、测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章，报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objections shall be wai

7、ved. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位：无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人： 审核人： 试验人： 单位地址：江苏省无锡

8、市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期： 2012-11-28 Report date: November 28, 2012上岗证号： B0035 B0322 B0377 电 话： 6，传真：6 Telephone: 6 Fax No.：6Certificate No. B0035 B0322 B0377 邮 编： 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位

9、无锡明阗通用设备制造有限公司 报告编号 B832a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B832a 委托单位 无锡明阗通用设备制造有限公司 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 J

10、MR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel section Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table

11、1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.130.550.230.0300.020该样品经检验，按GB/T706-2008标准评定：化学成分分析合格After the sample inspection, the analysis of chemical composition is acceptable in accordance with GB/T706-2008 Standard.牌号Marks规格Specification（mm）计算重量C

12、alculated weight（t）拉伸弯曲试验Bending Test（180O）代表数量Representative quantity（t）生产厂家Manufacturer质保书编号Warranty number结构部位 Sructural part检测结论Test conclusion屈服点sYield points（MPa）抗拉强度bTensile Strengthb（MPa）伸长率5Elongation5（%）Q235BL8083.22854352927.52.5马鞍山钢铁股份有限公司Maanshan Iron & Steel Co., Ltd煤斗Coal hopper该样品经检验

13、，按GB/T706-2008标准评定：机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明：1.若对报告有异议，应于收到报告之日期起十五日内，以书面形式向检测单位提出，逾期视为对报告无异议。 2.送样检测，检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章，报告无效。Notes for test report: 1.

14、In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objections shall be waived. 2. For entrusted tests, the test results presented in this r

15、eport relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位：无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人： 审核人： 试验人： 单位地址：江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jia

16、ngsu Director Reviewer: Tester: 报告日期： 2012-11-28 Report date: November 28, 2012上岗证号： B0035 B0322 B0377 电 话： 6，传真：6 Telephone: 6 Fax No.：6Certificate No. B0035 B0322 B0377 邮 编： 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造有限公司 报告编号 B833a Sample name: Angle steel Construction u

17、nit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B833a 委托单位 无锡明阗通用设备制造有限公司 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fir

18、ed boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel section Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMn

19、SiPS检测结论Test conclusionQ235B0.190.500.290.0400.028该样品经检验，按GB/T706-2008标准评定：化学成分分析合格After the sample inspection, the analysis of chemical composition is acceptable in accordance with GB/T706-2008 Standard.牌号Marks规格Specification（mm）计算重量Calculated weight（t）拉伸弯曲试验Bending Test（180O）代表数量Representative qua

20、ntity（t）生产厂家Manufacturer质保书编号Warranty number结构部位 Sructural part检测结论Test conclusion屈服点sYield points（MPa）抗拉强度bTensile Strengthb（MPa）伸长率5Elongation5（%）Q235BL6361.82553702727.51.8马鞍山钢铁股份有限公司Maanshan Iron & Steel Co., LtdZ33060940301灰库渣库Ash and slag silo该样品经检验，按GB/T706-2008标准评定：机械性能合格After the sample ins

21、pection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明：1.若对报告有异议，应于收到报告之日期起十五日内，以书面形式向检测单位提出，逾期视为对报告无异议。 2.送样检测，检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章，报告无效。Notes for test report: 1. In case of test discrepancy, objections shoul

22、d be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objections shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3

23、. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位：无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人： 审核人： 试验人： 单位地址：江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期： 2012-11

24、-28 Report date: November 28, 2012上岗证号： B0035 B0322 B0377 电 话： 6，传真：6 Telephone: 6 Fax No.：6Certificate No. B0035 B0322 B0377 邮 编： 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造有限公司 报告编号 B834a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufact

25、uring Co., Ltd Report number: B834a 委托单位 无锡明阗通用设备制造有限公司 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample st

26、atus: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel section Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.170.430.210.040

27、0.038该样品经检验，按GB/T706-2008标准评定：化学成分分析合格After the sample inspection, the analysis of chemical composition is acceptable in accordance with GB/T706-2008 Standard.牌号Marks规格Specification（mm）计算重量Calculated weight（t）拉伸弯曲试验Bending Test（180O）代表数量Representative quantity（t）生产厂家Manufacturer质保书编号Warranty number结

28、构部位 Sructural part检测结论Test conclusion屈服点sYield points（MPa）抗拉强度bTensile Strengthb（MPa）伸长率5Elongation5（%）Q235B10a36a3.531044531303.5马鞍山钢铁股份有限公司Maanshan Iron & Steel Co., LtdZ23070951014灰库渣库Ash and slag silo该样品经检验，按GB/T706-2008标准评定：机械性能合格After the sample inspection, mechanical properties are acceptable

29、 in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明：1.若对报告有异议，应于收到报告之日期起十五日内，以书面形式向检测单位提出，逾期视为对报告无异议。 2.送样检测，检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章，报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objections shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered