CCNA路由协议和概念第9单元.docx

1、CCNA路由协议和概念第9单元1窗体顶端Convert the binary number 10111010 into its hexadecimal equivalent. Select the correct answer from the list below. 85 90 BA A1 B3 1C 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 30 points for any other option 2This item references content from the

2、 following areas: CCNA Exploration: Network Fundamentals 9.3.3 Hexadecimal Numbering and Addressing 2窗体顶端Which of the following describe interframe spacing? (Choose two.) the minimum interval, measured in bit-times, that any station must wait before sending another frame the maximum interval, measur

3、ed in bit-times, that any station must wait before sending another frame the 96-bit payload padding inserted into a frame to achieve a legal frame size the 96-bit frame padding transmitted between frames to achieve proper synchronization the time allowed for slow stations to process a frame and prep

4、are for the next frame the maximum interval within which a station must send another frame to avoid being considered unreachable 窗体底端ObservableDescriptionMax Value1correctness of responseOption 1 and Option 5 are correct.1 point for each correct option.0 points if more options are selected than requ

5、ired. 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.4.4 Interframe Spacing and Backoff 3窗体顶端When a collision occurs in a network using CSMA/CD, how do hosts with data to transmit respond after the backoff period has expired? The hosts return to a li

6、sten-before-transmit mode. The hosts creating the collision have priority to send data. The hosts creating the collision retransmit the last 16 frames. The hosts extend their delay period to allow for rapid transmission. 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 1

7、0 points for any other option 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.4.2 CSMA/CD - The Process 4窗体顶端After an Ethernet collision, when the backoff algorithm is invoked, which device has priority to transmit data? the device involved in the col

8、lision with the lowest MAC address the device involved in the collision with the lowest IP address any device in the collision domain whose backoff timer expires first those that began transmitting at the same time 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 30 poin

9、ts for any other option 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.4.4 Interframe Spacing and Backoff 5窗体顶端Which of the following is a drawback of the CSMA/CD access method? Collisions can decrease network performance. It is more complex than non

10、-deterministic protocols. Deterministic media access protocols slow network performance. CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies. 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 10 points for any other option 2This item r

11、eferences content from the following areas: CCNA Exploration: Network Fundamentals 9.6.1 Legacy Ethernet - Using Hubs 6窗体顶端Refer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link? No co

12、llisions will occur on this link. Only one of the devices can transmit at a time. The switch will have priority for transmitting data. The devices will default back to half duplex if excessive collisions occur. 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 10 points f

13、or any other option 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.6.2 Ethernet - Using Switches 7窗体顶端Why do hosts on an Ethernet segment that experience a collision use a random delay before attempting to transmit a frame? A random delay is used to

14、ensure a collision-free link. A random delay value for each device is assigned by the manufacturer. A standard delay value could not be agreed upon among networking device vendors. A random delay helps prevent the stations from experiencing another collision during the transmission. 窗体底端ObservableDe

15、scriptionMax Value1correctness of response2 points for Option 40 points for any other option 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.4.2 CSMA/CD - The Process 8窗体顶端In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet fr

16、ame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do? Host B can transmit immediately since it is connected on its own cable segment. Host B must wait to receive a CSMA transmission from the hub, to signal its turn. Host B must send a request signal to Host A by

17、transmitting an interframe gap. Host B must wait until it is certain that Host A has completed sending its frame. 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 40 points for any other option 2This item references content from the following areas: CCNA Exploration: Net

18、work Fundamentals 9.4.2 CSMA/CD - The Process 9窗体顶端Ethernet operates at which layers of the OSI model? (Choose two.) Network layer Transport layer Physical layer Application layer Session layer Data-link layer 窗体底端ObservableDescriptionMax Value1correctness of responseOption 3 and Option 6 are correc

19、t.1 point for each correct option.0 points if more options are selected than required. 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.1.3 Logical Link Control - Connecting to the Upper Layers 10窗体顶端What does the IEEE 802.2 standard represent in Ether

20、net technologies? MAC sublayer Physical layer Logical Link Control sublayer Network layer 窗体底端ObservableDescriptionMax Value1correctness of response2 points for Option 30 points for any other option 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.1.3

21、Logical Link Control - Connecting to the Upper Layers 11窗体顶端Which statements correctly describe MAC addresses? (Choose three.) dynamically assigned copied into RAM during system startup layer 3 address contains a 3 byte OUI 6 bytes long 32 bits long 窗体底端ObservableDescriptionMax Value1correctness of

22、responseOption 2, Option 4, and Option 5 are correct.1 point for each correct option.0 points if more options are selected than required. 3This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.3.2 The Ethernet MAC Address 12窗体顶端Refer to the exhibit. Host_A i

23、s attempting to contact Server_B. Which statements correctly describe the addressing Host_A will generate in the process? (Choose two.) A packet with the destination IP of Router_B. A frame with the destination MAC address of Switch_A. A packet with the destination IP of Router_A. A frame with the d

24、estination MAC address of Router_A. A packet with the destination IP of Server_B. A frame with the destination MAC address of Server_B. 窗体底端ObservableDescriptionMax Value1correctness of responseOption 4 and Option 5 are correct.1 point for each correct option.0 points if more options are selected th

25、an required. 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.3.4 Another Layer of Addressing 13窗体顶端Host A has an IP address of 172.16.225.93, a mask of 255.255.248.0, and a default gateway of 172.16.224.1. Host A needs to send a packet to a new host w

26、hose IP is 172.16.231.78. Host A performs the ANDing operation on its address and subnet mask. What two things will occur? (Choose two.) Host A will get a result of 172.16.224.0 from the AND process. Host A will send on to the media a broadcast frame that contains the packet. Host A will broadcast a

27、n ARP request for the MAC of the host 172.16.231.78. Host A will change the destination IP of the packet to 172.16.224.1 and forward the packet. Host A will encapsulate the packet in a frame with a destination MAC that is the MAC address associated with 172.16.224.1. 窗体底端ObservableDescriptionMax Val

28、ue1correctness of responseOption 1 and Option 3 are correct.1 point for each correct option.0 points if more options are selected than required. 2This item references content from the following areas: CCNA Exploration: Network Fundamentals 9.7.1 The ARP Process - Mapping IP to MAC Addresses 14窗体顶端Wh

29、ich two features make switches preferable to hubs in Ethernet-based networks? (Choose two.) reduction in cross-talk minimizing of collisions support for UTP cabling division into broadcast domains increase in the throughput of communications 窗体底端ObservableDescriptionMax Value1correctness of responseOption 2 and Option 5 are correct.1 point for each correct option.0 points if more options are selected than required. 2