中兴透明通道各命令使用操作指南.docx

1、中兴透明通道各命令使用操作指南 如果不知道不同型号的RRU可以使用那些命令，直接进入之后输入HELP即可,有些命令是不通用的。1、 进入、退出：LI LO 退出的时候务必使用LO，否则会导致第二次进入的时候使用LI命令失败；2、 STA:RRU通道状态查询RRUSTARRU= RRU Status Info = RRUStat: Work! RFCh Stat: On RFCh Man Stat: On 主要查看RFCh Stat:ON为正常，OFF说明被降质R8968i M1920的查询结果为：RRUSTARRU= RRU Status Info = swRruWorkState:WorkF

2、reqBand: 0 LO: 180672. ChnNo #0TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #1TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #2TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #3TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #4TxPhy Sta:ON RxPhy Sta:ON TxM

3、an Sta:ON RxMan Sta:ON ChnNo #5TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #6TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #7TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON FreqBand: 1 LO: 180672. ChnNo #0TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #1TxPhy

4、 Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #2TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #3TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #4TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #5TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #6TxPhy

5、 Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON ChnNo #7TxPhy Sta:ON RxPhy Sta:ON TxMan Sta:ON RxMan Sta:ON The End.主要查看TxPhy Stat、RxPhy Sta、TxMan Sta和RxMan Sta是否为ON，如果是OFF说明被降质，通道有问题。3、 HDS：通道查询RRUHDSRRU= Hardware Status = FPGA Work Mode: normal mode Carrier Enable Status: Ca1-Enable Ca2-Enable Ca3-

6、Enable Ca4-Disable Ca5-Disable Ca6-DisableRFCh Enable Or Disable Status: Ch1-EnableRFCh Power Status: Ch1-Power OnTxIFAttenuate(RegVal):CH1-27hRxIFAttenuate(RegVal):CH1-2dhTx-Rx Switch Point: between ts2 and ts3 Slot PwrOnOff Status: Ts0-OnTs1-OnTs2-OnTs3-OnTs4-OnTs5-OnTs6-OnDwPts-OnGp-OnUpPts-OnPLL

7、 Status: LO PLL: Lock IF PLL: Lock OPTIC PLL: Lock 10M PLL: Lock Clk Status: 100Hz CLK: ok M for more.RRUMRRUIF CLK: ok OPTIC CLK: ok 10MHz CLK: ok IQLINKPORTADOWN_ALM: ok IQLINKPORTBUP_ALM : ok ANT1 DAC PLL: ok ANT1 DUC PLL: ok ANT1 DDC PLL: ok OVRTMP: ok OVRPWR: ok LOWPWR: ok Time Slot Control : T

8、S6:1H,TS5:1H TS4:1H,TS3:1H, TS2:1H, TS1:1H, UpPTS:1H, GP:1H, DwPTS:1H, TS0:1hTime Slot RxTx Mode : TS6:1H,TS5:1H TS4:1H,TS3:1H, TS2:1H, TS1:1H, UpPTS:1H, GP:1H, DwPTS:1H, TS0:1hOpt Up ALARM :LOP-ok LOS-ok LOF-okOpt DOWN ALARM :LOP-alarm LOS-alarm LOF-alarm可以看到Opt DOWN ALARM 存在告警，按照LOP-LOS-LOF的处理顺序，依

9、次处理4、 DPS模块状态查询DDS正常：RRUDDSRRU= DPD Current Status = Stream 0: DPD State Machine operation has been started.Stream 0: CMD_BEGIN was issued.Stream 0: DPD State Machine is currently running.Stream 0: The DPD State Machine is in state: 6*END*异常：RRUDDSRRU= DPD Current Status = Stream 0: DPD State Machin

10、e operation has NOT been started.Stream 0: CMD_BEGIN was NOT issued.Stream 0: DPD State Machine is currently NOT running.Stream 0: The DPD State Machine is in state: 1*END*5、 天线功率查询RRU11用SHOWANTPWR，RRU08i用ANTPWRSHOWANTPWRRRU11（查询接口）RRUSHOWANTPWRRRUReal power detection result: PathNo CarrNo CfgPwr De

11、tectIQPwr AntPwr : 0 2 24.8000 -28.6311 24.8353. 一般情况下，RRU11的CfgPwr和AntPwr在28左右，这个是异常的RRU查询信息。6、 RRU告警查询：DALMRRUDALMRRU= Total Alarm Info = OPTIC_LOP2_DOWN_ALMOPTIC_LOS2_DOWN_ALMOPITC_LOF2_DOWN_ALMThe End.和上面HDS查询到的告警是对应的，LOP,LOS,LOF都存在告警7、 PLL状态查询主要查看CNT状态是否有问题,以及DA值：RRUPLLRRU2011-04-11 17:17:12 72

12、 = PLL Status = LO PLL: Lock IF PLL: Lock OPTIC PLL: Lock 10M PLL: Lock = Clk Status = 100Hz CLK: ok IF CLK: ok OPTIC CLK: ok 10MHz CLK: ok 10M PLL Status Info: （正常情况下DA值一般在0x25000x5500范围内，如果达到或者接近0x7d00（或者达到或接近0x400）还没有锁定，同时没有其他异常，硬件异常的可能性最大，建议更换） Status TIE DA Time LOCKED 0 0x7f3c 3903 Warning : N

13、one M for more.RRUMRRUPLL 10M Code Version Build 080618. 10M PLL History Records: （这个时间是不准的）No Time Status KeepCnt TurnCnt LOST DA_OVER DITHER FREQ_OVER_PPM 1 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 2 2000-1 -1 0 :1 :3 UnLock 1 1 0 0 0 0 3 2000-1 -1 0 :2 :33 Lock 1 2 0 0 0 0 4 0 -0 -0 0 :0 :0 Lock 0 0 0 0

14、0 0 5 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 6 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 7 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 8 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 9 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 10 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 11 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 12 0 -0 -0 0 :0 :0 Lock 0 0 0 0 0 0 13 0 -0 -0 0

15、:0 :0 Lock 0 0 0 0 0 0 M for more.8、 RRU-BBU链路通畅查询LSTATRRULSTATRRU= Link Info = BBU-RRU: Ok The End.这个命令很奇怪，如果BBU与RRU通信链路断链，基本在透明通道是不能使用的，只能现场接RRU调测才能用。9、 HVI10、 CFGRRUCFGRRU= BBU Configuration Info = OptMode: IN_NORMAL AntGrp: byAntGrpNo WorkMode AntMask 1 WORKMODE_INTELLIGENT ffFiberMeasure OPT 0

16、UL IR: dwTDown: 890 (ns) dwTUp: 890 (ns) dwTBDelayDL: 8 (ns) dwTNext14: 0 (ns) dwTBDelayUL: 52897 (ns) dwTOffsetMwasure: 52905 (ns) TimeAhead: 80000 (ns) wBspTOffset: 158220 (ns) = Cell Info = CellID AntGrp MaxTxPwr(dbm) ParaID Status 15381 1 12032(47.0) 90 UNBLOCK-小区号、最大发射功率、扰码信息以及是否被闭塞M for more.R

17、RUMRRU= Cell Carr Info = CellID AntGrp Carr MainCarr Flag ARFCN TS FrmRatio SpecCfg CarrBW 15381 1 0 * TDS 20208 2:4 - - - 15381 1 1 - TDS 20176 2:4 - - - 15381 1 2 - TDS 20192 2:4 - - -No TDL_TYPE_CARR-小区频点配置以及时隙比The End.11、 HR查询RRU的历史告警信息RRUHRRRU= HR Info = HR Info Number: 51 HR Info: 1 .2013-08-1

18、9 09:21:55 410BBUCMD: RRU Send FiberDelayConfigRsp To BBU,Rst0! 2 .2013-08-19 09:21:55 120BBUCMD: RRU Rev ParaCfg-IQCfg Msg! M for more.12、 RESET:重启RRU13、 DCPU:查询CPU利用率RRUDCPURRU= CPU Usage = CPU use rate : 21 Last 5 CPU use rate data:00 : 2401 : 2302 : 1603 : 2604 : 20Average CPU use rate : 2114、 S

19、TPRBT:让RRU停止工作RRUSTPRBTRRUDisable RRU Reboot when Start without BBU!使用后RRU停止工作即不发射信号和接收信号，如果解蔽就用START.15、 DUB：该命令貌似是查询各类业务占用情况的RRUDUBRRU= UB Info = - UbLog Begin -The follow is about the config of User ub pool!*Show User UB Pool Summary Info now*dIndex Size Total free Reserve HIndex EInex 0 64 500 3

20、62 0 234 96 1 128 100 88 0 31 19 2 256 100 91 0 94 85 3 512 500 496 0 268 264 4 1024 100 97 0 46 43 5 2048 10 5 0 6 1 6 4096 10 7 0 4 1 7 8192 10 9 0 6 5 8 16384 10 9 0 3 2 9 32768 10 10 0 0 0 *Show User UB Pool Static Info now*static info,pool index = 0*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-w

21、CurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 156ptPoolCtlTmp-dwUBAlarmLimit = 450ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 18074234ptPoolCtlTmp-dwRUBNum = 18074096ptPoolCtlTmp-dwLUBNum = 0*static info,

22、pool index = 1*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 15ptPoolCtlTmp-dwUBAlarmLimit = 90ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 259631ptPoolCtlTmp-d

23、wRUBNum = 259619ptPoolCtlTmp-dwLUBNum = 0*static info,pool index = 2*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 11ptPoolCtlTmp-dwUBAlarmLimit = 90ptPoolCtlTmp-IsInUBAlarm

24、Period = 0ptPoolCtlTmp-dwGUBNum = 771294ptPoolCtlTmp-dwRUBNum = 771285ptPoolCtlTmp-dwLUBNum = 0*static info,pool index = 3*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 6ptP

25、oolCtlTmp-dwUBAlarmLimit = 450ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 819768ptPoolCtlTmp-dwRUBNum = 819764ptPoolCtlTmp-dwLUBNum = 0*static info,pool index = 4*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPo

26、olCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 4ptPoolCtlTmp-dwUBAlarmLimit = 90ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 8446ptPoolCtlTmp-dwRUBNum = 8443ptPoolCtlTmp-dwLUBNum = 0*static info,pool index = 5*ptPoolCtlTmp-dwUnsatisfyNum = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-

27、wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 9ptPoolCtlTmp-dwUBAlarmLimit = 9ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 20016ptPoolCtlTmp-dwRUBNum = 20011ptPoolCtlTmp-dwLUBNum = 0*static info,pool index = 6*ptPoolCtlTmp-dwUnsatisfy

28、Num = 0ptPoolCtlTmp-wCurrentCount = 0ptPoolCtlTmp-wHighestCount = 0ptPoolCtlTmp-dwMaxLackUB = 0ptPoolCtlTmp-dwCurLackUB = 0ptPoolCtlTmp-dwMaxUseUB = 6ptPoolCtlTmp-dwUBAlarmLimit = 9ptPoolCtlTmp-IsInUBAlarmPeriod = 0ptPoolCtlTmp-dwGUBNum = 134074ptPoolCtlTmp-dwRUBNum = 134071ptPoolCtlTmp-dwLUBNum = 0*