一清空配置HUAWEI reset savedconfiguration清楚下次启动时使.docx

1、一清空配置HUAWEI reset savedconfiguration清楚下次启动时使 一、清空配置： reset saved-configuration（清楚下次启动时使用的配置文件信息）然后重启设备，重启设备室提示保存信息，选择“NO”。 reset saved-configurationWarning: The action will delete the saved configuration in the device.The configuration will be erased to reconfigure. Continue? Y/N:yWarning: Now clear

2、ing the configuration in the device.Info: Succeeded in clearing the configuration in the device. rebootInfo: The system is now comparing the configuration, please wait.Warning: The configuration has been modified, and it will be saved to the next startup saved-configuration . Continue? Y/N:n /此处请选择“

3、N”Info: If want to reboot with saving diagnostic information, input N and then execute reboot save diagnostic-information.System will reboot! Continue?Y/N:y 二、通过STelnet/Telnet登录交换机设置新的Console口登录密码# 以登录用户界面的认证方式为密码认证，密码为Huawei123为例，配置如下。 system-viewHUAWEI user-interface console 0HUAWEI-ui-console0 au

4、thentication-mode passwordHUAWEI-ui-console0 set authentication password cipher Huawei123HUAWEI-ui-console0 return save# 以登录用户界面的认证方式为AAA认证，用户名为admin123，密码为Huawei123为例，配置如下。 system-viewHUAWEI user-interface console 0HUAWEI-ui-console0 authentication-mode aaaHUAWEI-ui-console0 quitHUAWEI aaaHUAWEI-aa

5、a local-user admin123 password irreversible-cipher Huawei123HUAWEI-aaa local-user admin123 service-type terminal（本地防务终端用户）HUAWEI-aaa return(返回) save（保存） 三、查看某个接口学习到的MAC地址 display mac-address dynamic gigabitethernet1/0/1MAC Address VLAN/VSI Learned-From Type -0000-0000-0003 300/- GE1/0/1 dynamic 0026

6、-6e5c-feac 3000/- GE1/0/1 dynamic 四、查看某个VLAN学习到的MAC地址 display mac-address dynamic vlan 10MAC Address VLAN/VSI Learned-From Type -0000-0000-0003 10/- GE1/0/1 dynamic 0026-6e5c-feac 10/- GE1/0/2 dynamic 五、查看系统的MAC地址 display interface gigabitethernet1/0/1GigabitEthernet1/0/1 current state : UP Line pro

7、tocol current state : UPDescription: Switch Port, Link-type : access(configured), IP Sending Frames Format is PKTFMT_ETHNT_2, Hardware address is00e0f74b-6d00 六、根据IP获取对应设备的MAC地址 display arp | include 192.168.150.20 配置端口安全# 配置GE1/0/1接口的端口安全功能。 system-viewHUAWEI interface gigabitethernet 1/0/1HUAWEI-G

8、igabitEthernet1/0/1 port-security enable# 配置GE1/0/1接口的MAC地址学习限制数为5，即最多可以学习到5个MAC地址表项。 system-viewHUAWEI interface gigabitethernet 1/0/1HUAWEI-GigabitEthernet1/0/1 port-security enableHUAWEI-GigabitEthernet1/0/1 port-security max-mac-num 5配置永久端口组# 配置接口GE1/0/1至GE1/0/8加入到永久端口组portgroup1（使用port-group命令）

9、 system-viewHUAWEI port-group portgroup1HUAWEI-port-group-portgroup1 group-member gigabitethernet 1/0/1 to gigabitethernet 1/0/8配置接口速率 自协商模式下，手动配置接口速率# 配置以太网接口GE1/0/1在自协商模式下协商速率为100Mbit/s。 system-viewHUAWEI interface gigabitethernet 1/0/1HUAWEI-GigabitEthernet1/0/1 negotiation autoHUAWEI-GigabitEthe

10、rnet1/0/1 auto speed 100配置双工模式 自协商模式下，手动配置双工模式 # 配置以太网电接口GE1/0/1在自协商模式下双工模式为全双工模式。 system-viewHUAWEI interface gigabitethernet 1/0/1HUAWEI-GigabitEthernet1/0/1 negotiation autoHUAWEI-GigabitEthernet1/0/1 auto duplex full配置接口切换到三层模式 接口视图下执行命令undo portswitch，配置接口切换到三层模式。# 将接口GE1/0/1切换为三层模式。 system-vie

11、wHUAWEI interface gigabitethernet 1/0/1HUAWEI-GigabitEthernet1/0/1 undo portswitchHUAWEI-GigabitEthernet1/0/1 ip address 10.10.10.10 255.255.255.0支持二层模式与三层模式切换的款型及版本如下：lS5700EI：V200R005C00&C01lS5700HI：V100R005C01、V100R006C01、V200R001C00、V200R002C00、V200R003C00、V200R005C00&C01lS5710EI：V200R002C00、V20

12、0R003C00、V200R005C00lS5720EI：V200R007C00、V200R008C00、V200R009C00、V200R010C00lS5710HI：V200R003C00、V200R005C00lS5720HI：V200R006C00、V200R007C00、V200R008C00、V200R009C00、V200R010C00lS6700EI：V200R005C00&C01lS6720EI：V200R008C00、V200R009C00、V200R010C00lS6720S-EI：V200R008C00、V200R009C00、V200R010C00lS7700&S97

13、00：V200R001C00&C01、V200R002C00、V200R003C00、V200R005C00、V200R006C00、V200R007C00、V200R008C00、V200R009C00、V200R010C00对于V200R005C00及后续版本，在接口使用命令undo portswitch，将以太网接口从二层模式切换到三层模式后，支持配置IP地址。一键清除接口下的配置 执行命令一键式清除接口下配置后，接口的状态将被置为shutdown状态。# 在系统视图下执行命令clear configuration interface清除GE1/0/1接口下的配置 system-view

14、HUAWEI clear configuration interface gigabitethernet 1/0/1Warning: All configurations of the interface will be cleared, and its state will be shutdown. Continue? Y/N :yInfo: Total 5 command(s) executed, 5 successful, 0 failed.查看设备支持的链路聚合组数目和成员接口数目# 查看设备支持的链路聚合组数目和成员接口数目。 display trunk configuration接

15、口加入VLANl Access接口加入VLAN system-viewHUAWEI interface gigabitethernet0/0/1HUAWEI-GigabitEthernet0/0/1 port link-type access /设置接口的链路类型为AccessHUAWEI-GigabitEthernet0/0/1 port default vlan 10 /把接口GigabitEthernet0/0/1加入VLAN 10Trunk接口加入VLAN system-viewHUAWEI interface gigabitethernet0/0/1HUAWEI-GigabitEth

16、ernet0/0/1 port link-type trunk /设置接口的链路类型为TrunkHUAWEI-GigabitEthernet0/0/1 port trunk allow-pass vlan 10 /把接口GigabitEthernet0/0/1加入VLAN 10Hybrid接口加入VLAN system-viewHUAWEI interface gigabitethernet0/0/1HUAWEI-GigabitEthernet0/0/1 port link-type hybrid /设置接口的链路类型为HybridHUAWEI-GigabitEthernet0/0/1 por

17、t hybrid tagged vlan 10 /接口GigabitEthernet0/0/1以Tagged方式加入VLAN 10HUAWEI-GigabitEthernet0/0/1 port hybrid untagged vlan 20 /接口GigabitEthernet0/0/1以Untagged方式加入VLAN 20批量创建VLAN批量创建10个连续的VLAN：VLAN11到VLAN20。 system-viewHUAWEI vlan batch 11 to 20批量创建10不连续的VLAN：VLAN10、VLAN15到VLAN19、VLAN25、VLAN28到VLAN30。 sy

18、stem-viewHUAWEI vlan batch 10 15 to 19 25 28 to 30接口批量加入VLANaccess接口类型。 system-viewHUAWEI port-group pg1 /创建端口组pg1HUAWEI-port-group-pg1 group-member gigabitethernet1/0/1 to gigabitethernet1/0/5 /把接口gigabitethernet1/0/1到gigabitethernet1/0/5加入端口组HUAWEI-port-group-pg1 port link-type access /批量修改端口gigab

19、itethernet1/0/1 to gigabitethernet1/0/5的链路类型为accessHUAWEI-port-group-pg1 port default vlan 10 /批量把端口gigabitethernet1/0/1 to gigabitethernet1/0/5加入VLAN10trunk接口类型。 system-viewHUAWEI port-group pg1 /创建端口组pg1HUAWEI-port-group-pg1 group-member gigabitethernet1/0/1 to gigabitethernet1/0/5 /把接口gigabitethe

20、rnet1/0/1到gigabitethernet1/0/5加入端口组HUAWEI-port-group-pg1 port link-type trunk /批量修改端口gigabitethernet1/0/1 to gigabitethernet1/0/5的链路类型为trunkHUAWEI-port-group-pg1 port trunk allow-pass vlan 10 20 /批量把端口gigabitethernet1/0/1 to gigabitethernet1/0/5加入VLAN10和VLAN20删除单个VLAN10。 system-viewHUAWEI undo vlan

21、10删除批量VLAN10到VLAN20。 system-viewHUAWEI undo vlan batch 10 to 20将接口类型修改为Access system-viewHUAWEI interface gigabitethernet0/0/1HUAWEI-GigabitEthernet0/0/1 port link-type accessHUAWEI-GigabitEthernet0/0/1 port default vlan 10 /设置接口的PVID为VLAN 10，并同时将VLAN 10加入接口将接口类型修改为Trunk system-viewHUAWEI interface gigabitethernet0/0/1HUAWEI-GigabitEthernet0/0/1 port link-type trunkHUAWEI-GigabitEthernet0/0/1 port trunk pvid vlan 10 /设置接口的PVID为VLAN 10HUAWEI-GigabitEthernet0/0/1 port trunk allow-pass vlan 2 10 20 /将VLAN 2、VLAN 10和VLAN 20加入接口