1、save以上配好就可以当交换机去用了。附图:如果出现的是 15 15 ,则需要再敲一遍该命令。硬件连接方式首先连接电脑与onu,通过配置线连接图为配置线,“网线头”插入onu的CONSOL日,另一端与电脑的串口接。图为onu上对应的CONSOL接口(插入“网线头”即可)电脑端操作首先打开超级终端: 开始一程序一附件-通信一超级终端打开超级中断后出现如下提示点否进入如下界面名称随便写图标选择默认的即可,然后点击确定出现如下界面连接口选择COM或者COM2艮据自己的机器选择,1不行就2,点击确定,然后按照下图设置还原刀眾认说j 确走取洎包用即点击确定然后到文件一属性一设置中按下图方式定要设置ASC
2、II 码按照图中行延迟和字符延迟都设置为 200毫秒,然后点击确定即在超级终端出点击回车即可出现要求输入用户名和密码华为onu登陆用户名root密码 mduadm in登陆后界面如下登陆onu后输入的命令:en able -回车erase flash data - 回车Y -回车reboot system- 回车Y-回车回车后等待片刻onu重启后以前所配置的数据即可全部删除查看光功率e nableMA5626#co nfigMA5626(config)#interface gponnni 0/0/1MA5626(config-if-gponnni-0/0/1)#display port sta
3、teF/S/P0/0/1Laser stateAUTOPort stateUpWave Length(nm)1310IdentifierModule/connector soldered tomotherboardGBIC/SFP function is defined by serial ID onlyConnectorOptical pigtailEncodingNRZBR,Nominal(100Mbps) 13Length(9um)(km)Length(50um)Not supportLength Not supportLength(Copper)Cc_base0xaaCC_EXT0x7
4、bBR,maxUnspecifiedBR,minInvalidOptionsVendor RevVendor PNSFU3424THPCDFIACVendor SNC4L2011876Vendor OUI000000Manufactured12-03-21Vendor nameSOURCEPHOTONICSTX Bias current(mA) Supply Voltage(V) Temperature(C)TX power(dBm)RX power(dBm)8 口实例 |profile-name :Command:vlan service-profile profile-id 1MA5626
5、(config-vlan-srvprof-1)#user-bridging enableInfo: Please use the commit command to make modifications take effectMA5626(config-vlan-srvprof-1)#commit MA5626(config-vlan-srvprof-1)#quitMA5626(config)#vlan bind service-profile 1 profile-id 1 MA5626(config)#multi-service-port vlan 1 port 0/1 1-8 user-v
6、lan untagged rx-cttr 6 tx-cttr 6It will take several minutes, and console maytimeout, please use commandidle-timeout to set time limitAre you sure to create service virtual port(s)? (y/n)n:yThe number of total board in this operation:1The number of total service virtual port in this operation:8Creat
7、ing start.Creating end:The number of total service virtual port which need be created:The number of total service virtual port which have been created: 8MA5626(config)#multi-service-port vlan 1 port 0/1 1-8 user-vlan untagged rx-cttr 6 tx-cttr 6 0MA5626(config)#savePOE功能数字光模块版的光口查询光功率MA5626(config-i
8、f-eth-0/0)#display port ?Command of eth Mode:ddm-info Display ddm information of optical module optic-power-threshold Display TX optical power threshold opticstate Display information of optical module state Display port state statistics Display port statistics traffic Display port traffic MA5626(co
9、nfig-if-eth-0/0)#display port opticstate all|portiddisplay port opticstateA% In complete comma nd, the error locates at A MA5626(config-if-eth-0/0)#display port opticstateall All portsportid Port IDMA5626(config-if-eth-0/0)#display port opticstate allPort bit 9um length 50um length length copper len
10、gth type rate supported supported supported supported (100M/s) (km) (10m) (10m) (m)1 2 21 10 55 M1000BASE_CX1 21 10 55M1000BASE_CX2 55 0MA5626(config-if-eth-0/0)#quitMA5626(config)#display board 00 H822EPUB Active_normal UP2A1 H821EPFA Normal2MA5626(config)#interface eth 0/055MA5626(config-if-eth-0/
11、0)#display port state allPort Port Optic MDI Speed Duplex Flow- Active Link Type Status (Mbps) Ctrl State1 GE normal - auto_1000 auto_full off active onlineactive2 GE absence - auto auto off offlineNote: For a 1000 M, electrical port in the full-duplex mode, setting MDI to any value is invalidMA5626
12、(config-if-eth-0/0)#display port ddm-info all% Parameter error, the error locates at MA5626(config-if-eth-0/0)#display port ddm-info portid display port ddm-infoMA5626(config-if-eth-0/0)#display port ddm-info 1Temperature(C) :Supply voltage(V) :TX bias current(mA) :TX power(dBm) :RX power(dBm) :MA5626(config-if-eth-0/0)#display port ddm-info 2Failure: The optic module of port is absence, can not do such operationMA5626(config-if-eth-0/0)#
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1