华为配置静态LACP模式链路聚合示例之欧阳学文创作Word文档格式.docx

1、图 配置静态LACP模式链路聚合组网图 配置思路采用如下的思路配置静态LACP模式链路聚合：在Switch设备上创建Eth-Trunk，配置Eth-Trunk为静态LACP模式。将成员接口加入Eth-Trunk。配置系统优先级确定主动端。配置活动接口上限阈值。配置接口优先级确定活动链路。数据准备为完成此配置例，需准备如下的数据：两端Switch设备链路聚合组编号。SwitchA系统优先级。活动接口上限阈值。活动接口LACP优先级。操作步骤创建编号为1的Eth-Trunk，配置它的工作模式为静态LACP模式 # 配置SwitchA。 system-viewQuidway sysname Swit

2、chASwitchA interface eth-trunk 1SwitchA-Eth-Trunk1 bpdu enableSwitchA-Eth-Trunk1 mode lacp-staticSwitchA-Eth-Trunk1 quit# 配置SwitchB。Quidway sysname SwitchBSwitchB interface eth-trunk 1SwitchB-Eth-Trunk1 bpdu enableSwitchB-Eth-Trunk1 mode lacp-staticSwitchB-Eth-Trunk1 quit将成员接口加入Eth-Trunk SwitchA int

3、erface ethernet 0/0/1SwitchA-Ethernet0/0/1 eth-trunk 1SwitchA-Ethernet0/0/1 quitSwitchA interface ethernet 0/0/2SwitchA-Ethernet0/0/2 eth-trunk 1SwitchA-Ethernet0/0/2 quitSwitchA interface ethernet 0/0/3SwitchA-Ethernet0/0/3 eth-trunk 1SwitchA-Ethernet0/0/3 quit# 配置SwitchB。SwitchB interface ethernet

4、 0/0/1SwitchB-Ethernet0/0/1 eth-trunk 1SwitchB-Ethernet0/0/1 quitSwitchB interface ethernet 0/0/2SwitchB-Ethernet0/0/2 eth-trunk 1SwitchB-Ethernet0/0/2 quitSwitchB interface ethernet 0/0/3SwitchB-Ethernet0/0/3 eth-trunk 1SwitchB-Ethernet0/0/3 quit在SwitchA上配置系统优先级为100，使其成为LACP主动端 SwitchA lacp priorit

5、y 100在SwitchA上配置活动接口上限阈值为2 SwitchA-Eth-Trunk1 max active-linknumber 2SwitchA-Eth-Trunk1 quit在SwitchA上配置接口优先级确定活动链路 SwitchA-Ethernet0/0/1 lacp priority 100SwitchA-Ethernet0/0/2 lacp priority 100验证配置结果 # 查看各Switch设备的Eth-Trunk信息，查看链路是否协商成功。SwitchA display eth-trunk 1Eth-Trunk1s state information is:Loc

6、al:LAG ID: 1 WorkingMode: STATICPreempt Delay: Disabled Hash arithmetic: According to SA-XOR-DASystem Priority: 100 System ID: 00e0-fca8-0417Least Active-linknumber: 1 Max Active-linknumber: 2Operate status: Up Number Of Up Port In Trunk:-ActorPortName Status PortType PortPri PortNo PortKey PortStat

7、e WeightEthernet0/0/1 Selected 1GE 100 6145 2865 11111100 1Ethernet0/0/2 Selected 1GE 100 6146 2865 11111100 1Ethernet0/0/3 Unselect 1GE 32768 6147 2865 11100000 1Partner:PartnerPortName SysPri SystemID PortPri PortNo PortKey PortStateEthernet0/0/1 32768 00e0-fca6-7f85 32768 6145 2609 11111100Ethern

8、et0/0/2 32768 00e0-fca6-7f85 32768 6146 2609 11111100Ethernet0/0/3 32768 00e0-fca6-7f85 32768 6147 2609 11110000SwitchB display eth-trunk 1 32768 System ID: 00e0-fca6-7f85 8Ethernet0/0/1 Selected 1GE 32768 6145 2609 11111100 1Ethernet0/0/2 Selected 1GE 32768 6146 2609 11111100 1Ethernet0/0/3 Unselec

9、t 1GE 32768 6147 2609 11100000 1Ethernet0/0/1 100 00e0-fca8-0417 100 6145 2865 11111100Ethernet0/0/2 100 00e0-fca8-0417 100 6146 2865 11111100Ethernet0/0/3 100 00e0-fca8-0417 32768 6147 2865 11110000通过以上显示信息可以看到，SwitchA的系统优先级为100，高于SwitchB的系统优先级。Eth-Trunk的成员接口中Ethernet 0/0/1、Ethernet 0/0/2成为活动接口，处于“

10、Selected”状态，接口Ethernet 0/0/3处于“Unselect”状态，同时实现M条链路的负载分担和N条链路的冗余备份功能。配置文件SwitchA的配置文件#sysname SwitchAlacp priority 100interface Eth-Trunk1mode lacp-staticmax active-linknumber 2bpdu enableinterface Ethernet0/0/1eth-trunk 1interface Ethernet0/0/2interface Ethernet0/0/3returnSwitchB的配置文件sysname SwitchBreturn