HP StorageWorks MSL磁带库Word下载.docx

1、MSL2024 Ultrium 920 （SCSI, SAS）MSL2024 Ultrium 960 （FC, SCSI）驱动器技术Ultrium（傲群）1840Ultrium（傲群）1760Ultrium（傲群）448Ultrium（傲群）920Ultrium（傲群）960驱动器数目11 个或 2 个插槽数24性能描述38.4TB4.8 TB 本机9.6 TB 压缩9.6 TB 本机19.2 TB 压缩接口4 Gb 本机光纤通道 Ultra320 LVD SCSI Ultra160 LVD SCSI 3 Gb/sec SASUltra160 LVD/SE SCSIUltra320 LVD/S

2、E SCSI 3Gb/sec SAS4Gb 本机光纤通道；Ultra320 SCSI LVD/SE最大传输速率 （1 个驱动器配置）1.152 TB/hr24 MB/s （86.4Gb/hr） 本机 48 MB/s （172.8 GB/hr） 压缩60 MB/s （216Gb/hr） 本机 120 MB/s （432 GB/hr） 压缩80 MB/s （288Gb/hr） 本机 160 MB/s （576 GB/hr） 压缩可靠性MSBF （平均无故障交换次数）平均无故障时间2,000,000 robot 载入/载出周期100000 小时（基于 1M MSBF）盒调换时间45 秒 （驱动器到插

3、槽，插槽到驱动器）启动时间65 到 80 秒接头（1） 微型 SAS （位于 MSL2024 SAS 机型后部，仅适用于该机型）（2） HD68 （位于 MSL2024 SCSI 机型后部，仅适用于该机型）（2） LC 光纤 （位于 MSL2024 FC 机型后部，仅适用于该机型）（1）RJ-45（位于 MSL2024 后部）（1） 个 USB 端口（仅诊断；位于 MSL2024 背面）库存时间1:20 分钟 （采用标有条形码的盒子）LED 指示灯（前面板）就绪 LED（绿色）： 显示就绪状态信息清洁 LED（黄色）： 显示故障状态信息警示 LED（黄色）：错误 LED（黄色）：保修此产品享有

4、一年、下一工作日现场保修服务。功能描述诊断工具HP StorageWorks Library and Tape Tools （L&TT）操作系统支持如需了解有关最新 OS 兼容性信息，请查阅 EBS 兼容性表。软件支持有关最新操作系统的兼容性信息，请参见 EBS 兼容性矩阵，网址为 有关产品规格信息，请点击这里 。点击此处了解保修信息 。此概述的信息来自于产品的规格概述。 要访问该产品的完整规格概述，请从下面的列表中选择所需的链接：点击此处访问 HP StorageWorks MSL2024 磁带库全球规格概述（html 格式） .点击此处访问 HP StorageWorks MSL2024

5、磁带库全球规格概述（pdf 格式） 。点击此处访问 HP StorageWorks MSL2024 磁带库北美地区规格概述（html 格式） .点击此处访问 HP StorageWorks MSL2024 磁带库北美地区规格概述（pdf 格式） 。点击此处访问规格概述主页，该页提供了对其他地区/国家的规格概述的访问 。hP StorageWorks MSL2024 磁带库 - 液晶屏菜单的操作说明HP StorageWorks MSL2024 磁带库液晶屏菜单的操作说明解决方案HP StorageWorks MSL2024 磁带库液晶屏菜单home-主菜单Unlock Mailslot-开启邮

6、槽oMailslot Unlocked-油槽开启oClose Mailslot- 关闭油槽Status/Information-状态/信息oInventory- 重新扫描磁带oLibrary information- 带库的信息oDrive1 information- 驱动器1的信息oDrive2 information- 驱动器2的信息oComponent status- 结构状态oNetwork information- 网络信息Configuration- 配置oChanging the administrator password- 更改管理员密码oSet Reserved Slot

7、Count- 设置保留的槽位oConfigure Mailslot- 配置油槽oBarcode Format Reporting-条形码版本的报告oChange Drive 1- 更改驱动器1的IDoChange Drive 2- 更改驱动器2的IDoSet Master Drive- 设置主驱动器oLibrary Behavior- 带库的状态oSet Date and Time- 设置时间和日期oConfigure Network Settings- 配置网络状态oRestoring defaults- 恢复工厂默认值Operations- 操作oUnlock Left Magazine-

8、 开启左面的槽位oUnlock Right Magazine- 开启右面的槽位oClean Drive- 清洗驱动器oMove Tape- 移动磁带oPerform Inventory- 重新扫描oReboot Library- 重启带库oEnable Library Password Locks- 启动带库密码锁Support- 支持oPower On/Off Drives- 驱动器电源开启关闭oRun Demo- 运行模式oRun Slot To Slot Test- 槽位到槽位的测试oDrive FW Upgrade- 升级驱动器的固件版本oForce Drive to Eject Ta

9、pe- 强制弹出磁带oLibrary Error Log- 带库错误日志oLibrary Warning Log- 带库警报日志oHP Service Area- HP 服务区HP StorageWorks MSL 磁带库 - 关于 MSL G3 带库自动清洗功能的说明问题本文介绍了MSL G3 带库自动清洗功能。MSL G3 带库自身都支持自动清洗功能，即在带库中有磁带机在需要清洗的时候，带库会自动使用之前放置好的带有CLN barcode开头的清洗带对需要清洗的磁带机进行清洗。清洗带需被放置在已经预留的槽位中。带库会记录每一盘清洗带的使用次数，当有多个清洗带被放置在带库中时，带库首先使用“

10、从未使用”的清洗带以便开始对所有的清洗带作使用记录，如果所有清洗带都已经被记录，那么，开库会使用被使用次数最多的清洗带。自动清洗需要手工开启，此功能在被开启的情况下，如果带库中没有清洗带，带库会有报警信息。启动清洗功能既可以从带库自身实现，也可以从备份软件实现，切忌不能二者同时设置。开启自动清洗功能操作比较简单，可以从远程管理卡的配置界面或者OCP面板上首先设置reserved slot，然后开启Auto Cleaning即可。标题: HP StorageWorks MSL2024 Tape Library - Installing the Tape Library文档代码: emr_na-c

11、01504408-2提交日期: 2008-07-14 05:56:09.0上次修改日期: 2008-07-29 10:15:46.0HP StorageWorks MSL2024 Tape Library - Installing the Tape LibraryOverviewPreparing the hostPlanning the parallel SCSI configurationAbout parallel SCSI bussesOptimizing throughputSCSI addressesPlanning the SAS configurationAbout SASSA

12、S cables and connectorsWorld Wide identifiersPlanning the Fibre Channel configurationDirect connectionSAN connectionChoosing a locationUnpacking the Tape LibraryIdentifying product componentsMounting the Library in a rackInstalling the Tabletop Conversion KitInstalling additional tape drivesChanging

13、 the SCSI address （parallel SCSI drives only）Connecting the parallel SCSI cable （parallel SCSI devices only）Connecting the Fibre Channel cables （Fibre Channel devices only）Connecting the SAS cable （SAS devices only）Powering on the LibraryThis document contains information about the installation proc

14、edures for the HP StorageWorks MSL2024 Tape Library （MSL2024）.NOTE: Use proper procedures to prevent electrostatic discharge. Use wrist-grounding straps and anti-static mats when handling internal components.Follow these general steps:If the host server is connected to a network, check with the syst

15、em administrator before powering off the computer.For parallel SCSI Tape Libraries, install a parallel SCSI host bus adapter （HBA） that supports multiple LUNs. Refer to the manuals for the host computer and the HBA for installation information.For SAS Tape Libraries, install a SAS host bus adapter （

16、HBA） with an external SAS 4x （IB） connector that supports multiple LUNs. Refer to the manuals for the host computer and the HBA for installation information. See Planning the SAS configuration for configuration requirements.For Fibre Channel Tape Libraries, install a FC host bus adapter （HBA） or ver

17、ify that there are sufficient ports available on a compatible Fibre Channel switch. See Planning the Fibre Channel configuration for configuration requirements.Install application software and compatible drivers on the host computer. See the application softwares manuals for installation and configu

18、ration information.For parallel SCSI Tape Libraries, make sure multiple LUN support is enabled on the HBA and operating system.If the host computer will have multiple parallel SCSI devices, you must decide how they will be configured into one or more parallel SCSI busses.A parallel SCSI bus consists

19、 of the host bus adapter （HBA）, the parallel SCSI devices, the parallel SCSI cables, and the terminators. The HBA and devices are connected in a chain, with each device connected to the next. The last device must have a SCSI terminator. Each device in the chain must have a unique SCSI address （SCSI

20、ID）.Complex devices, such as the Library, assign sub-addresses, called logical unit numbers （LUNs）, to different parts of the device. The HBA and operating system must support multiple LUNs, also called LUN scanning, for the application software to operate the Library. HP Smart Array controllers, mo

21、st third-party RAID controllers, and many on-board SCSI controllers do not support multiple LUNs.An HBA might have one or two channels, with each channel supporting one parallel SCSI bus. Check to see how many channels the HBA has and what devices are already connected to the HBA. Some devices, such

22、 as parallel SCSI disk drives, could be inside the server.The devices on a parallel SCSI bus share bandwidth so be careful about which devices you put together on a bus. Also, putting a single-ended （SE） SCSI device on the bus will slow all of the devices on the bus down to SE speed. Check each devi

23、ces interface specifications to see what kind of parallel SCSI interface it has.If possible, put each tape drive on its own parallel SCSI bus. For optimum performance, each LTO-3 or LTO-4 tape drive must be on its own Ultra 320 SCSI bus. Two LTO-2 tape drives can share an Ultra 320 SCSI bus or each

24、tape drive can be on its own Ultra 160 bus. This will give you the best performance and easiest installation.If a tape drive must share a parallel SCSI bus with one or more other devices or the Library has multiple tape drives that must share a bus, follow these guidelines to plan parallel SCSI buss

25、es for the highest performance:Do not put a tape drive on the same parallel SCSI bus as a disk drive because the system and backup performance will be slow when data is written from the hard drive to tape or from tape to the hard drive.Do not put a tape drive on the same parallel SCSI bus as a disk

26、array because the disk and the tape drive performance will be affected, most RAID controllers do not support multiple LUNs, and the data on the disk array could become corrupted.Avoid putting an SE SCSI device on the same bus as a tape drive because the SE device will slow the tape drive to SE speed

27、 and reduce the allowable cable length. The HBA also has a SCSI address, which is typically 7.Verify that each device on the bus has a unique SCSI address.MSL2024: For full-height tape drives the default SCSI address is 4. For half-height drives, the default SCSI address for the bottom drive is 4 an

28、d the default SCSI address for the top drive is 5 as shown in MSL2024 parallel SCSI tape drive default SCSI addresses .Figure 1: MSL2024 parallel SCSI tape drive default SCSI addresses1 - Tape drive with SCSI address 4 2 - Tape drive with SCSI address 5 If these pre-configured addresses will not be unique on a bus, you will need to change the SCSI address of one or more of the tape drives during the installation process. U