1、switch(enable) set system name name-string 2.在基于IOS的交换机上设置登录口令:switch(config)# enable password level 1 password 在基于CLI的交换机上设置登录口令:switch(enable) set password switch(enable) set enalbepass 3.在基于IOS的交换机上设置远程访问:switch(config)# interface vlan 1 switch(config-if)# ip address ip-address netmask switch(con
2、fig-if)# ip default-gateway ip-address 在基于CLI的交换机上设置远程访问:switch(enable) set interface sc0 ip-address netmask broadcast-address switch(enable) set interface sc0 vlan switch(enable) set ip route default gateway 4.在基于IOS的交换机上启用和浏览CDP信息:switch(config-if)# cdp enable switch(config-if)# no cdp enable 为了查看
3、Cisco邻接设备的CDP通告信息:switch# show cdp interface type modle/port switch# show cdp neighbors type module/port detail 在基于CLI的交换机上启用和浏览CDP信息:switch(enable) set cdp enable|disable module/port switch(enable) show cdp neighborsmodule/port vlan|duplex|capabilities|detail 5.基于IOS的交换机的端口描述:switch(config-if)# des
4、cription description-string 基于CLI的交换机的端口描述:switch(enable)set port name module/number description-string 6.在基于IOS的交换机上设置端口速度:switch(config-if)# speed10|100|auto 在基于CLI的交换机上设置端口速度:switch(enable) set port speed moudle/number 10|100|auto switch(enable) set port speed moudle/number 4|16|auto 7.在基于IOS的交换机
5、上设置以太网的链路模式:switch(config-if)# duplex auto|full|half 在基于CLI的交换机上设置以太网的链路模式:switch(enable) set port duplex module/number full|half 8.在基于IOS的交换机上配置静态VLAN:switch# vlan database switch(vlan)# vlan vlan-num name vla switch(vlan)# exit switch# configure teriminal switch(config)# interface interface module
6、/number switch(config-if)# switchport mode access switch(config-if)# switchport access vlan vlan-num switch(config-if)# end 在基于CLI的交换机上配置静态VLAN:switch(enable) set vlan vlan-num name name switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于IOS的交换机上配置VLAN中继线:switch(config)# interface interface mo
7、d/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation isl|dotlq switch(config-if)# switchport trunk allowed vlan remove vlan-list switch(config-if)# switchport trunk allowed vlan add vlan-list 在基于CLI的交换机上配置VLAN中继线:switch(enable) set trunk module/port on|of
8、f|desirable|auto|nonegotiate Vlan-range isl|dotlq|dotl0|lane|negotiate 10.在基于IOS的交换机上配置VTP管理域:switch(vlan)# vtp domain domain-name 在基于CLI的交换机上配置VTP管理域:switch(enable) set vtp domain domain-name 11.在基于IOS的交换机上配置VTP 模式:switch(vlan)# vtp sever|cilent|transparent switch(vlan)# vtp password password 在基于CL
9、I的交换机上配置VTP 模式:mode sever|cilent|transparent password password 12. 在基于IOS的交换机上配置VTP版本:switch(vlan)# vtp v2-mode 在基于CLI的交换机上配置VTP版本:switch(enable) set vtp v2 enable 13. 在基于IOS的交换机上启动VTP剪裁:switch(vlan)# vtp pruning 在基于CL I 的交换机上启动VTP剪裁:switch(enable) set vtp pruning enable 14.在基于IOS的交换机上配置以太信道:switch(
10、config-if)# port group group-number distribution source|destination 在基于CLI的交换机上配置以太信道:switch(enable) set port channel moudle/port-range modeon|off|desirable|auto 15.在基于IOS的交换机上调整根路径成本:switch(config-if)# spanning-tree vlan vlan-list cost cost 在基于CLI的交换机上调整根路径成本:switch(enable) set spantree portcost mo
11、udle/port cost switch(enable) set spantree portvlancost moudle/port cost costvlan-list 16.在基于IOS的交换机上调整端口ID:switch(config-if)# spanning-treevlan vlan-listport-priority port-priority 在基于CLI的交换机上调整端口ID:switch(enable) set spantree portpri mldule/portpriority switch(enable) set spantree portvlanpri modu
12、le/portpriority vlans 17. 在基于IOS的交换机上修改STP时钟:switch(config)# spanning-tree vlan vlan-list hello-time seconds switch(config)# spanning-tree vlan vlan-list forward-time seconds switch(config)# spanning-tree vlan vlan-list max-age seconds 在基于CLI的交换机上修改STP时钟:switch(enable) set spantree hello intervalvla
13、n switch(enable) set spantree fwddelay delay vlan switch(enable) set spantree maxage agingtiamevlan 18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:switch(config-if)#spanning-tree portfast 在基于CLI的交换机端口上启用或禁用Port Fast 特征:switch(enable) set spantree portfast module/portenable|disable 19. 在基于IOS的交换机端口上启用或禁用UplinkFa
14、st 特征:switch(config)# spanning-tree uplinkfast max-update-rate pkts-per-second 在基于CLI的交换机端口上启用或禁用UplinkFast 特征:switch(enable) set spantree uplinkfast enable|disablerate update-rate all-protocols off|on 20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP 地址,然后使用下列命令: switch(config)# cluster enable cluster-name 21
15、. 为了从一条中继链路上删除VLAN,可使用下列命令:switch(enable) clear trunk module/port vlan-range 22. 用show vtp domain 显示管理域的VTP参数. 23. 用show vtp statistics显示管理域的VTP参数. 24. 在Catalyst交换机上定义TrBRF的命令如下:switch(enable) set vlan vlan-name name name type trbrf bridge bridge-numstp ieee|ibm 25. 在Catalyst交换机上定义TrCRF的命令如下:switch
16、(enable) set vlan vlan-num name name type trcrf ring hex-ring-num|decring decimal-ring-num parent vlan-num 26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:switch(enable) set vlan vlan-num mod-num/port-num 27. 命令show spantree显示一个交换机端口的STP状态. 28. 配置一个ELAN的LES和BUS,可以使用下列命令:ATM (config)# int
17、erface atm number.subint multioint ATM(config-subif)# lane serber-bus ethernet elan-name 29. 配置LECS:ATM(config)# lane database database-name ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address
18、 ATM(lane-config-databade)# name 30. 创建完数据库后,必须在主接口上启动LECS.命令如下:ATM(config)# interface atm number ATM(config-if)# lane config database database-name ATM(config-if)# lane config auto-config-atm-address 31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:ATM(config)# interface atm number.subint multipoint ATM(config)# lan
19、e client ethernet vlan-num elan-num 32. 用show lane server 显示LES的状态. 33. 用show lane bus显示bus的状态. 34. 用show lane database显示LECS数据库可内容. 35. 用show lane client显示LEC的状态. 36. 用show module显示已安装的模块列表. 37. 用物理接口建立与VLAN的连接:router# configure terminal router(config)# interface media module/port router(config-if)
20、# description description-string router(config-if)# ip address ip-addr subnet-mask router(config-if)# no shutdown 38. 用中继链路来建立与VLAN的连接:router(config)# interface module/port.subinterface router(config-ig)# encapsulationisl|dotlq vlan-number router(config-if)# ip address ip-address subnet-mask 39. 用LA
21、NE 来建立与VLAN的连接:router(config)# interface atm module/port router(config-if)# no ip address router(config-if)# atm pvc 1 0 5 qsaal router(config-if)# atm pvc 2 0 16 ilni router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-mask router(con
22、fig-if)# lane client ethernet elan-num router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-name router(config-if)# lane client ethernet elan-name router(config-if)# 40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行: router(config)# ip routing router
23、(config)# router ip-routing-protocol router(config-router)# network ip-network-number 41. 配置默认路由:42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:router(config)# interface interface number router(config-if)# mls rp vlan-id vlan-id-num 43. 在路由处理器启用MLSP:router(config)# mls rp ip 44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中:
24、router(config)# interface interface number router(config-if)# mls rp vtp-domain domain-name 45. 查看指定的VTP域的信息:router# show mls rp vtp-domain vtp domain name 46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令: router(config-if)#mls rp management-interface 47. 要检验MLS-RP的配置情况:router# show mls rp 48. 检验特定接口上的MLS配置:rout
25、er# show mls rp interface interface number 49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:set mls flow destination|destination-source|full 50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令: router(config)# mls rp ip input-acl 51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:switch(enable) set mls enable 52. 若想改变老化时间的值,可在特权模式下输入以
26、下命令:switch(enable) set mls agingtime agingtime 53. 设置快速老化:switch(enable) set mls agingtime fast fastagingtime pkt_threshold 54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:switch(enable) show mls include 55. 显示MLS高速缓存记录:switch(enable) show mls entry 56. 用命令show in arp显示ARP高速缓存区的内容。57. 要把路由器配置为HSRP备份组
27、的成员,可以在接口配置模式下使用下面的命令:router(config-if)# standby group-number ip ip-address 58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下: router(config-if)# standy group-number preempt 59. 访问时间和保持时间参数是可配置的:router(config-if)# standy group-number timers hellotime holdtime 60. 配置HSRP跟踪:router(config-if)# standy group-number track type-number interface-priority 61. 要显示HSRP路由器的状态:router# show standby type-number group brief 62. 用命令show ip igmp确定当选的查询器。63. 启动IP组播路由选择
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1